Search NASA⌕ Search

Engineering topics

Zhang, Keni

Publications and source records attributed to Zhang, Keni.

Analysis of synergies in converting underground storage sites: Natural gas to hydrogen with co-located CO2 storage

This study examines the untapped potential of synergistically converting underground natural gas storage (UGS) into underground hydrogen storage (UHS) with co-located CO2 storage. Current approaches to subsurface storage technology (SST) development often prioritise single-use scenarios, overlooking the benefits of integrating multiple technologies. We investigate converting UGS assets into UHS through gradual cushion-gas injection over multiple years, rather than injecting all cushion gas in the first year, and include on-site CO2 storage to offset site emissions. Mechanistic modelling shows this gradual transition reduces the Levelised Cost of Storage (LCOS) of H2 by 1.2-13.1% while retaining energy output within 3% of the current status quo. We also show that combined UHS and CO2 storage hubs can reduce the LCOS of CO2 by 45-77% for only a 3-10% increase in hydrogen LCOS relative to the status quo. This analysis framework may help future-proof SST sites and support a resilient, economically beneficial energy transition.

Mouli-Castillo, Julien↗

TOUGH3/EOS7MG (EOS7MG) v1.1

EOS7MG is a new TOUGH3 module for modeling water, brine, and multiple gas mixtures in the subsurface multiphase flow system. The module allows mixture of as more as three gas components selecting from a list of predefined gases (CH4, C2H6, C3H8, H2S, CO2, N2, NO2, H2, and AIR). EOS7MG was developed based on EOS7C and inherited the general modeling capabilities of the TOUGH3 platform. It uses cubic equation of states for gas density, viscosity, and enthalpy calculation. The module provides the selection options for Peng-Robinson, Redlich-Kwong, or Soave-Redlich-Kwong equations of state. The subsurface flow and transport of gas and aqueous phase mixtures over a wide range of pressures and temperatures is modeled with a multiphase Darcy's Law and an accurate chemical equilibrium approach as originally implemented in EOS7C is used for calculation of the solubilities of different mass components. EOS7MG was designed to allow flexible number of components based on the number of gases included in the model. The potential application of this module may include subsurface gas storage, energy storage, CCS, enhanced gas recovery, and more.

Zhang, Keni↗

Advances in Multiphase Flow and Transport in the Subsurface Environment

Multiphase flow and transport processes in the subsurface environment are extremely important in a number of industrial and environmental applications at various spatial and temporal scales. Thus, it is necessary to identify, understand, and predict these processes to improve the production of conventional and unconventional oil and gas, to increase the safety of geological sequestration of carbon dioxide and nuclear waste disposal, and to make remediation of contaminated aquifers more effective.

54 ENVIRONMENTAL SCIENCES↗

Numerical studies of CO 2 and brine leakage into a shallow aquifer through an open wellbore

Industrial-scale geological storage of CO 2 in saline aquifers may cause CO 2 and brine leakage from abandoned wells into shallow fresh aquifers. This leakage problem involves the flow dynamics in both the wellbore and the storage reservoir. T2Well/ECO2N, a coupled wellbore-reservoir flow simulator, was used to analyze CO 2 and brine leakage under different conditions with a hypothetical simulation model in water-CO 2 -brine systems. Parametric studies on CO 2 and brine leakage, including the salinity, excess pore pressure (EPP) and initially dissolved CO 2 mass fraction, are conducted to understand the mechanism of CO 2 migration. The results show that brine leakage rates increase proportionally with EPP and inversely with the salinity when EPP varies from 0.5 to 1.5 MPa; however, there is no CO 2 leakage into the shallow freshwater aquifer if EPP is less than 0.5 MPa. The dissolved CO 2 mass fraction shows an important influence on the CO 2 plume, as part of the dissolved CO 2 becomes a free phase. Scenario simulation shows that the gas lifting effect will significantly increase the brine leakage rate into the shallow freshwater aquifer under the scenario of 3.89% dissolved CO 2 mass fraction. The equivalent porous media (EPM) approach used to model the wellbore flow has been evaluated and results show that the EPM approach could either under- or over-estimate brine leakage rates under most scenarios. The discrepancies become more significant if a free CO 2 phase evolves. Therefore, a model that can correctly describe the complex flow dynamics in the wellbore is necessary for investigating the leakage problems.

58 GEOSCIENCES↗

Numerical modeling study of a man-made low-permeability barrier for the compressed air energy storage in high-permeability aquifers

Compressed air energy storage (CAES) is a grid-scale energy storage technology for intermittent energy, as proven by the decades-long successful operation of two existing compressed air energy storage in cavern (CAESC) power plants. Because of the limited availability of salt domes appropriate for CAESC, the more widely available aquifers (compressed air energy storage in aquifers, CAESA) have recently attracted considerable attention as candidates for CAES. An ideal aquifer for CAESA is highly permeable around the well to facilitate easy injection and withdrawal of air, but the high-permeability region is surrounded by low-permeability zones to minimize the loss of injected air and decrease in energy efficiency. However, such ideal geological structures are not always available in nature. Therefore, the potential of creating man-made low-permeability barrier in high-permeability aquifers is very interesting. In this paper, we investigate the feasibility of man-made low-permeability barriers in high-permeability aquifers using the numerical simulator TOUGH2/Gel to calculate the three-component flow (including a miscible gelling liquid). The simulation results show that an expected low-permeability barrier can be created by injecting grout with certain properties, and the altered aquifer performs well for CAESA. Additional sensitivity studies are also performed to reveal the effects of the various factors on the success of the low-permeability barrier creation, including the critical solidification concentration, the scale factor of the time dependence of the grout viscosity, the relative density of the grout, and the volume of the follow-up water injection. The results indicate that, in a horizontal aquifer, low critical solidification concentrations, and small scale factors are generally preferred and the density of grout should be close to that of the in situ water. For the given volume of the injected grout, there is an optimal follow-up water injection that will create the largest storage space without damaging the barrier. Furthermore, these results may help to extend the candidate sites for CAESA and the prospect of large scale energy storage.

25 ENERGY STORAGE↗

Numerical investigation of a joint approach to thermal energy storage and compressed air energy storage in aquifers

Different from conventional compressed air energy storage (CAES) systems, the advanced adiabatic compressed air energy storage (AA-CAES) system can store the compression heat which can be used to reheat air during the electricity generation stage. Thus, AA-CAES system can achieve a higher energy storage efficiency. Similar to the AA-CAES system, a compressed air energy storage in aquifers (CAESA) system, which is integrated with an aquifer thermal energy storage (ATES) could possibly achieve the same objective. In order to investigate the impact of ATES on the performance of CAESA, different injection air temperature schemes are designed and analyzed by using numerical simulations. Key parameters relative to energy recovery efficiencies of the different injection schemes, such as pressure distribution and temperature variation within the aquifers as well as energy flow rate in the injection well, are also investigated in this study. The simulations show that, although different injection schemes have a similar overall energy recovery efficiency (~97%) as well as a thermal energy recovery efficiency (~79.2%), the higher injection air temperature has a higher energy storage capability. Our results show the total energy storage for the injection air temperature at 80 °C is about 10% greater than the base model scheme at 40 °C. Sensitivity analysis reveal that permeability of the reservoir boundary could have significant impact on the system performance. However, other hydrodynamic and thermodynamic properties, such as the storage reservoir permeability, thermal conductivity, rock grain specific heat and rock grain density, have little impact on storage capability and the energy flow rate. Our study suggests that the combination of ATES and CAESA can help keep the high efficiency of energy storage so as to make CAESA system more efficiency.

25 ENERGY STORAGE↗

Comparison of compressed air energy storage process in aquifers and caverns based on the Huntorf CAES plant

CAESA (compressed air energy storage in aquifers) attracts more and more attention as the increase need of large scale energy storage. The compassion of CAESA and CAESC (compressed air energy storage in caverns) can help on understanding the performance of CAESA, since there is no on running CAESA project. In order to investigate the detail thermodynamic process, integrated wellbore-reservoir (cavern or aquifer) simulations of CAES (compressed air energy storage) are carried out based on parameters of the Huntorf CAES plant. Reasonable matches between monitored data and simulated results are obtained for the Huntorf cavern systems in the wellbore and cavern regions. In this study, the hydrodynamic and thermodynamic behaviors of CAES in cavern and aquifer systems are investigated, such as pressure and temperature distribution and variation in both the wellbore and cavern regions of the CAES systems. Performances of CAESA are investigated with numerical models and compared with the performances of CAESC. The comparisons of CAESC and CAESA indicate that the pressure variation in CAESA shows a wider variation range than that in CAESC, while the temperature shows a smooth variation due to the large grain specific heat of the grains in the porous media. The simulation results confirm that the CAES can be achieved in aquifers, and further that the performance of energy storage in aquifers can be similar to or better than CAESC, if the aquifers have appropriate reservoir properties, which means the gas bubble can be well developed in an aquifer with such properties and the aquifer should have closed or semi-closed boundaries. The impacts of gas-bubble volume, formation permeability, and aquifer boundary permeability on storage efficiency are investigated and the simulation results indicate that the increase of gas bubble volume and permeability can improve the efficiency, but the effect is not significant. The gas bubble boundary permeability has a small effect on the energy efficiency of the sustainable daily cycle but can significantly affect total sustainable cycle times. The analysis of thermodynamic behaviors in CAESA suggests that more attention should be paid to the heat storage, reservoir properties and two-phase flow processes.

25 ENERGY STORAGE↗

User's guide of TOUGH2-EGS-MP: A Massively Parallel Simulator with Coupled Geomechanics for Fluid and Heat Flow in Enhanced Geothermal Systems VERSION 1.0

TOUGH2-EGS-MP is a parallel numerical simulation program coupling geomechanics with fluid and heat flow in fractured and porous media, and is applicable for simulation of enhanced geothermal systems (EGS). TOUGH2-EGS-MP is based on the TOUGH2-MP code, the massively parallel version of TOUGH2. In TOUGH2-EGS-MP, the fully-coupled flow-geomechanics model is developed from linear elastic theory for thermo-poro-elastic systems and is formulated in terms of mean normal stress as well as pore pressure and temperature. Reservoir rock properties such as porosity and permeability depend on rock deformation, and the relationships between these two, obtained from poro-elasticity theories and empirical correlations, are incorporated into the simulation. This report provides the user with detailed information on the TOUGH2-EGS-MP mathematical model and instructions for using it for Thermal-Hydrological-Mechanical (THM) simulations. The mathematical model includes the fluid and heat flow equations, geomechanical equation, and discretization of those equations. In addition, the parallel aspects of the code, such as domain partitioning and communication between processors, are also included. Although TOUGH2-EGS-MP has the capability for simulating fluid and heat flows coupled with geomechanical effects, it is up to the user to select the specific coupling process, such as THM or only TH, in a simulation. There are several example problems illustrating applications of this program. These example problems are described in detail and their input data are presented. Their results demonstrate that this program can be used for field-scale geothermal reservoir simulation in porous and fractured media with fluid and heat flow coupled with geomechanical effects.

15 GEOTHERMAL ENERGY↗