Engineering topics
Zhang, Pu
Publications and source records attributed to Zhang, Pu.
Solid State Li Ion Batteries Using Si Composite Anodes
Solid Power has teamed with Argonne National Laboratory (ANL) to develop an all solid-state lithium-ion battery (ASSB), enabled by a high-capacity Si anode and a solid state electrolyte (SSE). Replacing liquid electrolytes with solid electrolytes addresses the calendar life challenges that currently limit the widespread adoption of Si anodes. In this project, Si-SSE composite materials have been developed with a specific capacity >1500 mAh/g (at electrode level). A Si anode was coated by using a roll-to-roll process. All-solid-state NMC-Si pouch cells have been assembled and tested. Cycle life of 1100 at 100% DOD has been demonstrated in the solid state Si pouch cell. Excellent calendar life is achieved in the cell via a high temperature storage test.
Distribution and source identification of polycyclic aromatic hydrocarbons (PAHs) with PCA-MLR and PMF methods in the topsoil of Chengdu at SW, China
Not provided.
Electrolytes with moderate lithium polysulfide solubility for high-performance long-calendar-life lithium–sulfur batteries
Lithium–sulfur (Li-S) batteries with high energy density and low cost are promising for next-generation energy storage. However, their cycling stability is plagued by the high solubility of lithium polysulfide (LiPS) intermediates, causing fast capacity decay and severe self-discharge. Exploring electrolytes with low LiPS solubility has shown promising results toward addressing these challenges. However, here, we report that electrolytes with moderate LiPS solubility are more effective for simultaneously limiting the shuttling effect and achieving good Li-S reaction kinetics. We explored a range of solubility from 37 to 1,100 mM (based on S atom, [S]) and found that a moderate solubility from 50 to 200 mM [S] performed the best. Using a series of electrolyte solvents with various degrees of fluorination, we formulated the S ingle- S olvent, S ingle- S alt, S tandard S alt concentration with M oderate L i PSs so l ubility E lectrolytes (termed S 6 MILE ) for Li-S batteries. Among the designed electrolytes, Li-S cells using fluorinated-1,2-diethoxyethane S 6 MILE (F4DEE-S 6 MILE) showed the highest capacity of 1,160 mAh g −1 at 0.05 C at room temperature. At 60 °C, fluorinated-1,4-dimethoxybutane S 6 MILE (F4DMB-S 6 MILE) gave the highest capacity of 1,526 mAh g −1 at 0.05 C and an average CE of 99.89% for 150 cycles at 0.2 C under lean electrolyte conditions. This is a fivefold increase in cycle life compared with other conventional ether-based electrolytes. Moreover, we observed a long calendar aging life, with a capacity increase/recovery of 4.3% after resting for 30 d using F4DMB-S 6 MILE. Furthermore, the correlation between LiPS solubility, degree of fluorination of the electrolyte solvent, and battery performance was systematically investigated.
High-entropy electrolytes for practical lithium metal batteries
Electrolyte engineering is crucial for improving battery performance, particularly for lithium metal batteries. Recent advances in electrolytes have greatly improved cyclability by enhancing electrochemical stability at the electrode interfaces, but concurrently achieving high ionic conductivity has remained challenging. Here we report an electrolyte design strategy for enhanced lithium metal batteries by increasing the molecular diversity in electrolytes, which essentially leads to high entropy electrolytes (HEEs). We find that in weakly solvating electrolytes, the entropy effect reduces ion clustering while preserving the characteristic anion-rich solvation structures, which is characterized by synchrotron-based X-ray scattering and molecular dynamics simulations. Electrolytes with smaller- sized clusters exhibit a 2-fold improvement in ionic conductivity compared to conventional weakly- solvating electrolytes, enabling stable cycling at high current densities up to 2C (6.2 mA cm -2 ) in anode- free LiNi 0.6 Mn 0.2 Co 0.2 (NMC622)||Cu pouch cells. In conclusion, the efficacy of the design strategy is verified by performance improvements in three disparate weakly solvating electrolyte systems.
Ni Anchored to Hydrogen-Substituted Graphdiyne for Lithium Sulfide Cathodes in Lithium–Sulfur Batteries
Lithium–sulfur (Li–S) batteries are promising candidates for next-generation energy storage systems due to their high theoretical energy density and the low cost of sulfur. However, slow conversion kinetics between the insulating S and lithium sulfide (Li 2 S) remains as a technical challenge. In this work, we report a catalyst featuring nickel (Ni) single atoms and clusters anchored to a porous hydrogen-substituted graphdiyne support (termed Ni@HGDY), which is incorporated in Li 2 S cathodes. The rapidly synthesized catalyst was found to enhance ionic and electronic conductivity, decrease the reaction overpotential, and promote more complete conversion between Li 2 S and sulfur. The addition of Ni@HGDY to commercial Li 2 S powder enabled a capacity of over 516 mAh g Li 2 S –1 at 1 C for over 125 cycles, whereas the control Li 2 S cathode managed to maintain just over 200 mAh g Li 2 S –1 . In conclusion, these findings highlight the efficacy of Ni as a metal catalyst and demonstrate the promise of HGDY in energy storage devices.
Ultrahigh-Loading Manganese-Based Electrodes for Aqueous Batteries via Polymorph Tuning
Manganese-based aqueous batteries utilizing Mn 2+ /MnO 2 redox reactions are promising choices for grid-scale energy storage due to their high theoretical specific capacity, high power capability, low-cost, and intrinsic safety with water-based electrolytes. However, the application of such systems is hindered by the insulating nature of deposited MnO 2 , resulting in low normalized areal loading (0.005–0.05 mAh cm -2 ) during the charge/discharge cycle. Here, in this work, the electrochemical performance of various MnO 2 polymorphs in Mn 2+ /MnO 2 redox reactions is investigated, and ε-MnO 2 with low conductivity is determined to be the primary electrochemically deposited phase in normal acidic aqueous electrolyte. It is found that increasing the temperature can change the deposited phase from ε-MnO 2 with low conductivity to γ-MnO 2 with two order of magnitude increase in conductivity. It is demonstrated that the highly conductive γ-MnO 2 can be effectively exploited for ultrahigh areal loading electrode, and a normalized areal loading of 33 mAh cm -2 is achieved. At a mild temperature of 50 °C, cells are cycled with an ultrahigh areal loading of 20 mAh cm -2 (1–2 orders of magnitude higher than previous studies) for over 200 cycles with only 13% capacity loss.
All Solid State Batteries Enabled by Multifunctional Electrolyte Materials
Solid Power has teamed with University of California San Diego to develop a high energy, long life, low cost, and safe all-solid-state-battery (ASSB). The battery is enabled by a multifunctional solid state electrolyte (SSE). The project enables scalable production of large format solid state batteries required by the vehicle market and building domestic battery manufacturers as leaders in the global vehicle ASSB production. In the project, the multifunctional SSE materials have been developed and optimized with ionic conductivity ≥ 5 mS/cm and electrochemical stability 0 – 4.5V. SSE separator films have been coated by using a roll-to-roll process with thickness ≤ 40 µm. All-solid-state NMC-Li pouch cells containing the developed SSE have been assembled. A cycle life of > 750 at 100% DOD and 45 °C has been demonstrated in a full pouch cell.
Batteries (2021 Annual Progress Report)
This document summarizes the progress of VTO battery R&D projects supported during the fiscal year 2021 (FY 2021). In FY 2021, the DOE VTO battery R&D funding was approximately $\$$115 million. Its R&D focus was on the development of high-energy batteries for EVs as well as very high-power devices for hybrid vehicles. The electrochemical energy storage roadmap (which can be found at the EERE Roadmap web page2) describes ongoing and planned efforts to develop electrochemical storage technologies for EVs. To advance battery technology, which can in turn improve market penetration of PEVs, the program investigates various battery chemistries to overcome specific technical barriers, e.g., battery cost, performance, life (both the calendar life and the cycle life), its tolerance to abusive conditions, and its recyclability/sustainability. VTO R&D has had considerable success, lowering the cost of EV battery packs to $\$$185/kWh in 2019 (representing more than 80% reduction since 2008) yet even further cost reduction is necessary for EVs to achieve head-to-head cost competitiveness with ICEs (without Federal subsidies). In addition, today’s batteries also need improvements in such areas as their ability to accept charging at a high rate, referred to as extreme fast charging (XFC) (15 minute charge) – to provide a “refueling” convenience similar to ICEs, and the ability to operate adequately at low temperatures. Research into “next-gen lithium-ion” batteries which would provide such functionalities is one of the R&D focus areas. VTO is funding research on both “next gen” chemistries (which employ an alloy anode and/or a high voltage cathode) and beyond lithium-ion (BLI) chemistries (which can, for example, employ a lithium metal anode).
All-Solid-State Lithium–Sulfur Batteries Enhanced by Redox Mediators
We report redox mediators (RMs) play a vital role in some liquid electrolyte-based electrochemical energy storage systems. However, the concept of redox mediator in solid-state batteries remains unexplored. Here, we selected a group of RM candidates and investigated their behaviors and roles in all-solid-state lithium-sulfur batteries (ASSLSBs). The soluble-type quinone-based RM (AQT) shows the most favorable redox potential and the best redox reversibility that functions well for lithium sulfide (Li 2 S) oxidation in solid polymer electrolytes. Accordingly, Li 2 S cathodes with AQT RMs present a significantly reduced energy barrier (average oxidation potential of 2.4 V) during initial charging at 0.1 C at 60 °C and the following discharge capacity of 1133 mAh g s -1 . Using operando sulfur K-edge X-ray absorption spectroscopy, we directly tracked the sulfur speciation in ASSLSBs and proved that the solid-polysulfide-solid reaction of Li 2 S cathodes with RMs facilitated Li 2 S oxidation. In contrast, for bare Li 2 S cathodes, the solid-solid Li 2 S-sulfur direct conversion in the first charge cycle results in a high energy barrier for activation (charge to ~4 V) and low sulfur utilization. The Li 2 S@AQT cell demonstrates superior cycling stability (average Coulombic efficiency 98.9% for 150 cycles) and rate capability owing to the effective AQT-enhanced Li-S reaction kinetics. This work reveals the evolution of sulfur species in ASSLSBs and realizes the fast Li-S reaction kinetics by designing an effective sulfur speciation pathway
Changing chemistry of particulate manganese in the near- and far-field hydrothermal plumes from 15°S East Pacific Rise and its influence on metal scavenging
Dissolved Mn(II) in the hydrothermal plume is known to be microbially oxidized to form Mn(III/IV) oxides, and the Mn oxides scavenge other trace elements in seawater. In the GEOTRACES GP16 cruise, dissolved Mn (dMn) and particulate Mn (pMn) were found to be transported over 4000 km westwards from the Southern Eastern Pacific Rise. Previous studies in this plume showed different removal rates of dMn and pMn as well as pMn size distribution between the near-field (<80 km from the ridge axis) and far-field (>80 km) plumes. In order to understand Mn cycling in these plumes, spatial distribution, oxidation states, and mineral structures of Mn in small size fraction (SSF; 0.8–51 μm) and large size fraction (LSF; >51 μm) particles from the near-field and far-field plumes were examined using micro X-ray fluorescence spectrometry (μ-XRF), X-ray absorption near-edge structure spectroscopy (XANES), chemical species mapping, and extended X-ray absorption fine-structure spectroscopy (EXAFS). In the near-field plume, pMn in the SSF is dominated by oxidized Mn with Mn(III) fractions of ~30%. They are a mixture of δ-MnO 2 and triclinic birnessites that is known to be formed as a result of autocatalytic Mn(II) oxidation at the surface of freshly-formed δ-MnO2, suggesting that both microbial and autocatalytic Mn oxidation occur in the near-field plume. The LSF pMn in the near-field plume is also oxidized and often found in large aggregates several hundreds of μm in size. These aggregates settle out in the near-field and during transport, and are not found in the far-field plume. In the far-field plume where Mn oxides are not newly formed, pMn in the SSF is oxidized, but their Mn(III) fractions are smaller than in the near-field pMn. Unlike the SSF, the far-field plume LSF pMn is dominated by reduced Mn, implying very slow aggregation of pMn in the far-field plume. The different characteristics of pMn between the near-field and far-field plumes affect its scavenging of other trace elements. In the near-field plume, Co, Mo, 231 Pa are associated with pMn, but not in the far-field plume. 231 Pa is adsorbed to pFe rather than pMn in the far-field plume, and Pb is adsorbed to pFe in the entire plume. The result shows that freshly-formed Mn oxides in the near-field plume have higher scavenging capacity than the far-field plume pMn. Our findings suggest that the mineralogical age of Mn oxides may be an important parameter that controls the scavenging of many other trace elements and isotopes.
Promoting H2O2 production via 2-electron oxygen reduction by coordinating partially oxidized Pd with defect carbon
Explore the source record for details and available documents.
Incorporating the Nanoscale Encapsulation Concept from Liquid Electrolytes into Solid-State Lithium–Sulfur Batteries
Solid-state Li–S batteries are attractive due to their high energy density and safety. However, it is unclear whether the concepts from liquid electrolytes are applicable in the solid state to improve battery performance. Here, we demonstrate that the nanoscale encapsulation concept based on Li 2 S@TiS 2 core–shell particles, originally developed in liquid electrolytes, is effective in solid polymer electrolytes. Using in situ optical cell and sulfur K-edge X-ray absorption, we find that polysulfides form and are well-trapped inside individual particles by the nanoscale TiS 2 encapsulation. We see that this TiS 2 encapsulation layer also functions to catalyze the oxidation reaction of Li 2 S to sulfur, even in solid-state electrolytes, proven by both experiments and density functional theory calculations. A high cell-level specific energy of 427 W·h·kg –1 is achieved by integrating the Li 2 S@TiS 2 cathode with a poly(ethylene oxide)-based electrolyte and a lithium metal anode. This study points to the fruitful direction of borrowing concepts from liquid electrolytes into solid-state batteries.
Apparatus and method for processing battery electrodes
An apparatus for processing battery electrodes includes: a microwave applicator cavity with slots on opposite ends to allow a continuous sheet to move through the cavity in a first direction; a processing chamber constructed of microwave-transparent material, disposed within the applicator cavity and surrounding the continuous sheet, the processing chamber having slots to allow the continuous sheet to pass through it; a microwave power supply to deliver power to the applicator cavity; a source of heated gas providing a controlled gas flow through the processing chamber in a direction opposite the first direction; and, at least one non-contacting temperature measuring device positioned to measure a surface temperature at a selected location on the continuous sheet as it passes through the processing chamber. The apparatus is particularly suited for removing polar solvents from porous electrode coatings. A related method is also disclosed.
A Nonparametric Bayesian Framework for Short-Term Wind Power Probabilistic Forecast
To improve the energy system resilience and economic efficiency, the wind power as a renewable energy starts to be deeply integrated into smart power grids. However, the wind power forecast uncertainty brings operational challenges. In order to provide a reliable guidance on operational decisions, in this paper, we propose a short-term wind power probabilistic forecast. Specifically, to model the rich dynamic behaviors of underlying physical wind power stochastic process occurring in various meteorological conditions, we first introduce an infinite Markov switching autoregressive model. This nonparametric time series model can capture the important properties in the real world data to improve the prediction accuracy. Then, given finite historical data, the posterior distribution of flexible forecast model can correctly quantify the model estimation uncertainty. Built on it, we develop the posterior predictive distribution to rigorously quantify the overall forecasting uncertainty accounting for both inherent stochastic uncertainty and model estimation error. Furthermore, the proposed approach can provide accurate and reliable short-term wind power probabilistic forecast, which can be used to support smart power grids real-time risk management.
Androgen-responsive circular RNA circSMARCA5 is up-regulated and promotes cell proliferation in prostate cancer
Prostate cancer (PCa) is one of the most commonly diagnosed cancers in males worldwide. Circular RNA (circRNA) is a unique class of RNA transcribed by RNA polymerase II characterized by jointing 3′ and 5′ ends together via exon or intron circularization. However, the molecular functions of circRNAs in prostate cancer have rarely been explored. In present study, we found circ-SMARCA5 was up-regulated in prostate cancer samples compared to match normal tissues. We also observed circ-SMARCA5 expression was significantly induced after DHT treatment. Functional experiments showed circ-SMARCA5 acted as an oncogene in prostate cancer by promoting cell cycle and inhibiting cell apoptosis. We thought this study provided useful information for exploring circRNAs as potential therapeutic and prognostic targets for prostate cancer. - Highlights: • To our knowledge, this is the first study to explore the molecular functions of circRNA in prostate cancer. • Our study showed that circ-SMARCA5 promoted cell proliferation and inhibited cell apoptosis in prostate cancer. • circ-SMARCA5 was for the first time reported as an androgen-responsive circRNA. • circ-SMARCA5 was for the first time reported to be up-regulated in prostate cancer.
Advanced Drying Process for Lower Manufacturing Cost of Electrodes
For this Vehicle Technologies Incubator/Energy Storage R&D topic, Lambda Technologies teamed with Navitas Systems and proposed a new advanced drying process that promised a 5X reduction in electrode drying time and significant reduction in the cost of large format lithium batteries used in PEV's. The operating principle of the proposed process was to use penetrating radiant energy source Variable Frequency Microwaves (VFM), that are selectively absorbed by the polar water or solvent molecules instantly in the entire volume of the electrode. The solvent molecules are thus driven out of the electrode thickness making the process more efficient and much faster than convective drying method. To evaluate the Advanced Drying Process (ADP) a hybrid prototype system utilizing VFM and hot air flow was designed and fabricated. While VFM drives the solvent out of the electrode thickness, the hot air flow exhausts the solvent vapors out of the chamber. The drying results from this prototype were very encouraging. For water based anodes there is a 5X drying advantage (time & length of oven) in using ADP over standard drying system and for the NMP based cathodes the reduction in drying time has 3X benefit. For energy savings the power consumption measurements were performed to ADP prototype and compared with the convection standard drying oven. The data collected demonstrated over 40% saving in power consumption with ADP as compared to the convection drying systems. The energy savings are one of the operational cost benefits possible with ADP. To further speed up the drying process, the ADP prototype was explored as a booster module before the convection oven and for the electrode material being evaluated it was possible to increase the drying speed by a factor of 4, which could not be accomplished with the standard dryer without surface defects and cracks. The instantaneous penetration of microwave in the entire slurry thickness showed a major advantage in rapid drying of the electrode materials. For the existing electrode materials, the material analysis and cell characterization data from ADP dried electrodes showed equivalent (or slightly better) performance. However, for high loading and thicker electrode materials (for high energy densities) the ADP advantages are more prominent. There was less binder migration, the resistance was lower hence the current capacities and retention of the battery cells were higher. The success of the project has enabled credible communications with commercial end users as well as battery coating line integrators. Goal is to scale ADP up for high volume manufacturing of Li-ion battery electrodes. The implementation of ADP in high volume manufacturing will reduce a high cost production step to bring the overall price of Li-ion batteries down. This will ultimately have a positive impact on the public by making electric and hybrid vehicles more affordable.