Search NASA⌕ Search

Engineering topics

Zhang, Songwei

Publications and source records attributed to Zhang, Songwei.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Design and Synthesis of Cubic K 3−2 x Ba x SbSe 4 Solid Electrolytes for K–O 2 Batteries

Developing K-ion conducting solid-state electrolytes (SSEs) plays a critical role in the safe implementation of potassium batteries. In this work, a chalcogenide-based potassium ion SSE is reported, K 3 SbSe 4 , which adopts a trigonal structure at room temperature. Single-crystal structural analysis reveals a trigonal-to-cubic phase transition at the low temperature of 50 °C, which is the lowest among similar compounds and thus provides easy access to the cubic phase. The substitution of barium for potassium in K 3 SbSe 4 leads to the creation of potassium vacancies, expansion of lattice parameters, and a transformation from a trigonal phase to a cubic phase. As a result, the maximum conductivity of K 3−2x Ba x SbSe 4 reaches around 0.1 mS cm −1 at 40 °C for K 2.2 Ba 0.4 SbSe 4 , which is over two orders of magnitude higher than that of undoped K 3 SbSe 4 . This novel SSE is successfully employed in a K–O 2 battery operating at room temperature where a polymer-laminated K 2.2 Ba 0.4 SbSe 4 pellet serves as a separator between the oxygen cathode and the potassium metal anode. Effective protection of the K metal anode against corrosion caused by O 2 is demonstrated.

25 ENERGY STORAGE↗
DOE OSTI2022

Phase Transfer‐Mediated Degradation of Ether‐Based Localized High‐Concentration Electrolytes in Alkali Metal Batteries

Abstract Localized high‐concentration electrolytes (LHCEs) have attracted interest in alkali metal batteries due to the advantages of forming stable solid‐electrolyte interphases (SEIs) on anodes and good chemical/electrochemical stability. Herein, a new degradation mechanism is revealed for ether‐based LHCEs that questions their compatibility with alkali metal anodes (Li, Na, and K). Specifically, the ether solvent reacts with alkali metals to generate solvated electrons (e s − ) that attack hydrofluoroether co‐solvents to form a series of byproducts. The ether solvent essentially acts as a phase‐transfer reagent that continuously transfers electrons from solid‐phase metals into the solution phase, thus inhibiting the formation of stable SEI and leading to continuous alkali metal corrosion. Switching to an ester‐based solvating solvent or intercalation anodes such as graphite or molybdenum disulfide has been shown to avoid such a degradation mechanism due to the absence of e s − .

Chen, Xiaojuan↗
DOE OSTI2022

Phase Transfer‐Mediated Degradation of Ether‐Based Localized High‐Concentration Electrolytes in Alkali Metal Batteries

Abstract Localized high‐concentration electrolytes (LHCEs) have attracted interest in alkali metal batteries due to the advantages of forming stable solid‐electrolyte interphases (SEIs) on anodes and good chemical/electrochemical stability. Herein, a new degradation mechanism is revealed for ether‐based LHCEs that questions their compatibility with alkali metal anodes (Li, Na, and K). Specifically, the ether solvent reacts with alkali metals to generate solvated electrons (e s − ) that attack hydrofluoroether co‐solvents to form a series of byproducts. The ether solvent essentially acts as a phase‐transfer reagent that continuously transfers electrons from solid‐phase metals into the solution phase, thus inhibiting the formation of stable SEI and leading to continuous alkali metal corrosion. Switching to an ester‐based solvating solvent or intercalation anodes such as graphite or molybdenum disulfide has been shown to avoid such a degradation mechanism due to the absence of e s − .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

K 3 SbS 4 as a Potassium Superionic Conductor with Low Activation Energy for K–S Batteries

Abstract Solid‐state K‐ion conducting electrolytes are key elements to address the current problems in K secondary batteries. Here, we report a sulfide‐based K‐ion conductor K 3 SbS 4 with a low‐activation energy of 0.27 eV. W‐doped K 3− x Sb 1− x W x S 4 ( x =0.04, 0.06, 0.08, 0.10 and 0.12) compounds were also explored for increasing vacancy concentrations and improving ionic conductivity. Among them, K 2.92 Sb 0.92 W 0.08 S 4 exhibits the highest conductivity of 1.4×10 −4 S cm −1 at 40 °C, which is among the best reported potassium‐ion conductors at ambient temperature. In addition, K 2.92 Sb 0.92 W 0.08 S 4 is electrochemically stable with long‐chained potassium polysulfide of K 2 S x . A room‐temperature solid potassium–sulfur (K−S) battery system has therefore been successfully demonstrated, which is the first K−S battery prototype using non‐commercial inorganic‐based electrolyte to block the polysulfide shuttle.

Shao, Jieren↗
DOE OSTI2022

K 3 SbS 4 as a Potassium Superionic Conductor with Low Activation Energy for K–S Batteries

Abstract Solid‐state K‐ion conducting electrolytes are key elements to address the current problems in K secondary batteries. Here, we report a sulfide‐based K‐ion conductor K 3 SbS 4 with a low‐activation energy of 0.27 eV. W‐doped K 3− x Sb 1− x W x S 4 ( x =0.04, 0.06, 0.08, 0.10 and 0.12) compounds were also explored for increasing vacancy concentrations and improving ionic conductivity. Among them, K 2.92 Sb 0.92 W 0.08 S 4 exhibits the highest conductivity of 1.4×10 −4 S cm −1 at 40 °C, which is among the best reported potassium‐ion conductors at ambient temperature. In addition, K 2.92 Sb 0.92 W 0.08 S 4 is electrochemically stable with long‐chained potassium polysulfide of K 2 S x . A room‐temperature solid potassium–sulfur (K−S) battery system has therefore been successfully demonstrated, which is the first K−S battery prototype using non‐commercial inorganic‐based electrolyte to block the polysulfide shuttle.

25 ENERGY STORAGE↗
DOE OSTI2020

Ambient Pressure XPS Investigation of Thermally Stable Halide Perovskite Solar Cells via Post-Treatment

Long-term thermal stability is one limiting factor that impedes the commercialization of perovskite solar cell. Inspired by our prior results from machine learning, we discover that coating a thin layer of 4,4’-dibromotriphenylamine (DBTPA) on top of a CH 3 NH 3 PbI 3 (MAPbI 3 ) thin film can improve the stability of the resultant perovskite solar cells. The passivated perovskite solar cells retained more than 96% of their initial power conversion efficiency over 1000 h at 85 °C in N2 atmosphere without encapsulation. Near-ambient pressure x-ray photoelectron spectroscopy (NAP-XPS) was employed to investigate the evolution of composition and evaluate thermal and moisture stability by in-situ studies. A comparison between pristine MAPbI 3 films and DBTPA-treated films shows the DBTPA treatment suppresses the escape of iodide and methylamine up to 150 °C under 5 mbar humidity. Furthermore, we have used ATR-FTIR and XPS to probe the interactions between DBTPA and MAPbI3 surface. The results prove that DBTPA coordinate with perovskite by Lewis acid-base and cation-π interaction. Compared with the 19.9% efficiency of pristine sample, the champion efficiency of passivated sample reaches 20.6%. Finally, our results reveal DBTPA as a new post-treating molecule that not only leads to the improvement of photovoltaic efficiency but also thermal and moisture stability.

14 SOLAR ENERGY↗
DOE OSTI2020

Pursuing graphite-based K-ion O 2 batteries: a lesson from Li-ion batteries

The replacement of lithium metal by lithium intercalated graphite was crucial for developing safe lithium-ion batteries. Superoxide-based potassium–oxygen batteries represent an exciting metal–oxygen battery with the highest energy efficiencies. However, using potassium metal is a more serious safety threat than lithium. Herein, we explore the possibility of graphite-intercalation anodes for potassium-ion oxygen batteries (PIOBs) with enhanced safety. This work demonstrates for the first time that establishing an artificial potassium salt-rich solid electrolyte interphase (SEI) enables a reversible graphite-intercalation anode (249.6 mA h g -1 after 600 cycles) in a potassium bis(trifluoromethanesulfonyl)imide (KTFSI)-based localized high-concentration electrolyte. Such an electrolyte is stable with the superoxide cathode. The PIOB delivers energy efficiencies above 90% at a depth of discharge (DOD) of 25% for 80 cycles. A three-electrode measurement shows that its overpotential mainly comes from the anode. The lifespan is limited to the gradual degradation of the artificial SEI caused by oxygen crossover. This work represents a step towards achieving holistic anode–electrolyte–cathode compatibility in a PIOB and its realistic evaluation under a controlled DOD.

25 ENERGY STORAGE↗
DOE OSTI2020

From K‐O 2 to K‐Air Batteries: Realizing Superoxide Batteries on the Basis of Dry Ambient Air

Abstract Although using an air cathode is the goal for superoxide‐based potassium‐oxygen (K‐O 2 ) batteries, prior studies were limited to pure oxygen. Now, the first K‐air (dry) battery based on reversible superoxide electrochemistry is presented. Spectroscopic and gas chromatography analyses are applied to evaluate the reactivity of KO 2 in ambient air. Although KO 2 reacts with water vapor and CO 2 to form KHCO 3 , it is highly stable in dry air. With this knowledge, rechargeable K‐air (dry) batteries were successfully demonstrated by employing dry air cathode. The reduced partial pressure of oxygen plays a critical role in boosting battery lifespan. With a more stable environment for the K anode, a K‐air (dry) battery delivers over 100 cycles (>500 h) with low round‐trip overpotentials and high coulombic efficiencies as opposed to traditional K‐O 2 battery that fails early. This work sheds light on the benefits and restrictions of employing the air cathode in superoxide‐based batteries.

Qin, Lei↗