Search NASA⌕ Search

Engineering topics

Zhang, Xiaoxiao

Publications and source records attributed to Zhang, Xiaoxiao.

At least 19 records

In-situ electrochemical optical techniques in the investigation of lithium interfacial phenomena with a liquid and a solid-state electrolyte

An in-situ electrochemical optical diagnosis is the key to the investigation of electrode interface during a redox reaction. Because the morphology changes particularly, dendrite formation, dendrite shapes, solid electrolyte interface formation and gas generation can be revealed visually. The challenge of ensuring uniform current density on a flat Li anode in a liquid electrolyte was addressed and uniform Li plating was demonstrated. The dendrite shape change under different reduction current density was discussed. Here the Li dendrite shape change and the performance of Li anodes with a surface lamination of graphite and red phosphate were used as examples to demonstrate the capability of the in-situ optical cell. An in-situ electrochemical optical cell used in the investigation of the increasingly popular solid-state Li batteries has its own challenges. Due to the untransparent nature of a solid-state electrolyte, an optical investigation on a solid-state electrolyte Li battery needs to be done by exposing the cross-section of the cell. In addition, it is very difficult to assemble an optical cell with a brittle and fragile solid-state electrolyte in a glove box. A set of formation and transfer dies, and an optical cell were introduced. The Li dendrite growth at the interface can be observed in a solid-state Li cell.

25 ENERGY STORAGE↗

High-performance all-solid-state Li–S batteries enabled by an all-electrochem-active prelithiated Si anode

The development of all-solid-state Li–S batteries has been greatly impeded by dendrite growth and dendrite penetration, which are both related to the Li metal anode. As a compromised alternative, we report lithium silicide (Li x Si) as a dendrite-free and high-capacity anode with Li source. Here, the as-synthesized Li x Si is relatively soft, highly electronically conductive, and with a high Li diffusivity. These distinctive properties make Li x Si anode viable as an “all-electrochem-active” electrode (consisted of 100 wt.% Li x Si). Compared with the typical composite electrode, the all-electrochem-active electrode not merely maximizes the electrode-level energy density but also minimizes the electrolyte-related interfacial degradation. Li x Si symmetric cell demonstrates a reversible cycling at 4 mA cm –2 for over 320 h. Stress change and morphological evolution of the Li x Si electrode are investigated upon dealloying/alloying. When paired with a S cathode (active mass loading of 3 mg cm –2 ), Li x Si–S full cell shows a good cycling behavior over 500 cycles and rate performance (69% capacity retained at 1.2C) even at 25 °C.

25 ENERGY STORAGE↗

Practically Accessible All-Solid-State Batteries Enabled by Organosulfide Cathodes and Sulfide Electrolytes

The combination of organic electrode materials and sulfide electrolytes is expected to enable the development of all-solid-state organic batteries featuring high energy density and long-term sustainability. In this work, thiuram hexasulfide is reported as a low-cost and high-capacity organic cathode for solid-state batteries based on sulfide electrolytes, delivering a capacity of ~600 mAh g -1 and retaining 80.8 % capacity after 500 cycles. An electrochemically reversible change of the cathode interface was revealed upon cycling. Full cell displays an oscillating stress change up to 0.6 MPa during cycling, predominated by the anode side. The energy density is 1140 Wh kg -1 at the material level and 376 Wh kg -1 at the electrode level, which are among the best-reported organic cathodes to date. A high areal capacity of 10.4 mAh cm -2 is reached with a high mass loading cathode. A dry-film approach is further explored to manufacture sheet-type cells. Free-standing electrolyte film is merely ~48 μm thick and demonstrates an ultralow areal resistance of 3.9 Ω cm 2 , significantly boosts the cell-level energy density and reduces the cell internal resistance.

25 ENERGY STORAGE↗

Polyimide as a durable cathode for all-solid-state Li(Na)–organic batteries with boosted cell-level energy density

The integration of organic electrode materials (OEMs) with solid-state electrolytes (SSEs) is expected to build an all-solid-state battery (ASSB) with long-term sustainability, high safety, and high energy density. Despite this great promise, the cell-level energy density is still far from practically applicable, which stems from the ultrathick SSE layer and thin cathode layer used in a pellet-type ASSB design. Here, a cost-effective polyimide (PI) material was first exploited as an organic cathode for sulfide-based ASSBs. A capacity of ~190 mAh g -1 was delivered with almost no capacity decay over 300 cycles. Moreover, for the first time, a dry-film approach was introduced to manufacture a sheet-type Li–organic ASSB with an ultrathin SSE layer and a high-areal-loading PI cathode. Notably, PI is a perfect candidate for dry-film technology due to its high thermal stability and extraordinary chemical inertness toward sulfide SSEs. Remarkably, the free-standing SSE membrane was merely 46 μm thick, and an ultralow areal resistance of 3.3 Ω cm 2 was achieved, more than tenfold lower than that of reported SSE pellets. One order of magnitude boost in the cell-level energy density was achieved. This work presents a significant leap in transferring organic ASSB technology from laboratory research to factory manufacturing.

25 ENERGY STORAGE↗

A high-performance organic cathode customized for sulfide-based all-solid-state batteries

All-solid-state batteries (ASSBs) have become increasingly attractive recently due to their better safety and prospective long-term stability compared with conventional liquid batteries. However, obtaining a sustainable cathode candidate to match the solid electrolyte with regards to operating potential, chemical compatibility, and mechanical property is still an open challenge. In this work, the chemical incompatibility of quinone-based active materials and sulfide-based electrolyte were unveiled for the first time through a heteroconjugate addition reaction mechanism. To develop a quinone cathode customized for sulfide-based ASSBs, poly-(anthraquinonyl sulfide)-graphene (PAQS-G) nanocomposite was reported. The stable polymer framework of PAQS can protect the quinone redox center by preventing nucleophilic attack from sulfide-based solid electrolytes. The graphene additives can ameliorate redox kinetics and improve active material utilization. The PAQS-G cathode exhibited a specific capacity of ~178 mAh g -1 and a high material utilization of ~79%. Excellent cycling stability was achieved with 94 % capacity after 200 cycles in lithium batteries and 95.5 % capacity after 300 cycles in sodium batteries at 0.1C rate, respectively. A promising potential for energy storage applications was demonstrated.

25 ENERGY STORAGE↗

A redox-active organic cation for safer metallic lithium-based batteries

Safety concerns have severely impeded the practical application of high-energy-density lithium-based batteries. Dendrite growth and overcharging can lead to particularly catastrophic thermal failure. Here we report an organic cation, trisaminocyclopropenium (TAC), as a bi-functional electrolyte additive to suppress dendrite growth and offer reversible overcharge protection for metallic lithium-based batteries. During the Li plating process, TAC cations with aliphatic chains can form a positively charged electrostatic shield around Li protrusions, repelling the approaching Li + and thereby attaining a more uniform plating. A two times longer cycle life of 300 h at 1 mA cm -2 is achieved in a Li|Li symmetric cell in comparison with the control. During the overcharging process, the redox-active TAC can repeatedly shuttle between two electrodes, maintaining the cell voltage within a safe value. A solid protection of 117 cycles (~1640 h) at 0.2 C with a 100% overcharge is achieved in a LiFePO 4 /Li 4 Ti 5 O 12 cell. This study sheds fresh light on the ability of organic cations to build safer batteries.

25 ENERGY STORAGE↗

A redox-active organic cation for safer high energy density Li-ion batteries

Ni-rich layered cathode materials are at the forefront to be deployed in high energy density Li-ion batteries for the automotive market. However, the intrinsic poor structural and interfacial stability during overcharging could trigger violent thermal failure, which severely limits their wide application. To protect the Ni-rich cathode from overcharging, we firstly report a redox-active cation, thioether-substituted diaminocyclopropenium, as an electrolyte additive to limit the cell voltage within the safe value during overcharging. The organic cation demonstrates a record-breaking electrochemical reversibility at ~4.55 V versus Li + /Li and solubility (0.5 M) in carbonate-based electrolyte. The protection capability of the additive was explored in two cell chemistries: a LiNi 0.8 Co 0.15 Al 0.05 O 2 /graphite cell and a LiNi 0.8 Co 0.15 Al 0.05 O 2 /silicon–graphene cell with areal capacities of ~2.2 mA h cm -2 and ~3 mA h cm -2 , respectively. With 0.2 M addition, the LiNi 0.8 Co 0.15 Al 0.05 O 2 /graphite cell survived 54 cycles at 0.2C with 100% overcharge. Moreover, the cell can carry an utmost 4.4 mA cm -2 (2C) with 100% overcharge and a maximum capacity of 7540% SOC at 0.2C.

25 ENERGY STORAGE↗

A facile recovery process for cathodes from spent lithium iron phosphate batteries by using oxalic acid

A simplistic and novel leaching process is developed to dispose spent lithium iron phosphate (LiFePO 4 ) batteries. In this paper, oxalic acid is selected as a leaching reagent to recover lithium as a resource and remove phosphorus from LiFePO 4 batteries, benefiting from its low natural effects. The physical properties of spent cathode materials (before leaching) and residues (after leaching) are identified by X-ray diffraction (XRD) and scanning electronic microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS). The total amounts of Li and Fe are analyzed by inductively coupled plasma-atomic emission spectroscopy (ICP-AES). The process occurs under conditions of a 0.3 mol·L -1 oxalic acid concentration, a temperature of 80°C, a reaction time of 60 min and a solid/liquid ratio of 60 g· L -1 . It can effectively precipitate ~92% ferrum in terms of FeC 2 O 4 ·2H 2 O from LiFePO 4 , with the leaching efficiency of Li achieving up to 98%. This method demonstrates a new strategy for dealing with spent lithium iron phosphate batteries with a low cost and low environmental impact.

25 ENERGY STORAGE↗

Cloud transitions: comparison of temporal variation in the southeastern Pacific with the spatial variation in the northeastern Pacific at low latitudes

ABSTRACT The seasonal variation of clouds in the southeastern equatorial Pacific ( SEP ) is analysed and compared with the spatial variation of clouds in the northeastern Pacific along the Global Energy and Water Cycle Experiment Cloud System Study/Working Group on Numerical Experimentation ( GCSS / WGNE ) Pacific Cross‐Section Intercomparison ( GPCI ) transect. A ‘seasonal cloud transition’ – from stratocumulus to shallow cumulus and eventually to deep convection – is found in the SEP from September to April, which is similar to the spatial cloud transition along the GPCI transect from the California coast to the equator. It is shown that this seasonal cloud transition in the SEP is associated with increasing sea surface temperature ( SST ), decreasing lower tropospheric stability and large‐scale subsidence, which are all similar to the spatial variation of these fields along the GPCI transect. Difference is found that the SEP cloud transition is associated with decreasing surface wind speed and surface latent heat flux, weaker larger‐scale upward motion and convective instability, which lead to less deepening of the low clouds and less frequent deep convection than those in the GPCI transect. The seasonal cloud transition in the SEP provides a test for climate models to simulate the relationships between clouds and large‐scale atmospheric fields in a region that features a spurious double inter‐tropical convergence zone ( ITCZ ) in most models.

54 ENVIRONMENTAL SCIENCES↗

Design of surface protective layer of LiF/FeF 3 nanoparticles in Li-rich cathode for high-capacity Li-ion batteries

Advanced lithium-ion batteries for renewable energy storage applications have become a major research interest in recent years. Much better performance can be realized by improvements in the material surface design, especially for the cathode materials. Here, we present a new design for a surface protective layer formed via a facile aqueous solution process in which a nano-architectured layer of LiF/FeF 3 is epitaxially grown on bulk hierarchical Li-rich cathode Li[Li 0.2 Ni 0.2 Mn 0.6 ]O 2 . Coin cell tests of this material in the voltage range of 2–4.8 V indicated a high reversible capacity (260.1 mA h g -1 at 0.1 C), superior rate performance (129.9 mA h g -1 at 20 C), and excellent capacity retention. Differential scanning calorimetry showed good thermal stability. The enhanced capacity and cycling stability are attributed to the suppression of interfacial side reactions as well as the conversion reaction resulting from the introduction of LiF/FeF 3 as a surface protective layer.

Iron fluoride↗

Succinic acid-based leaching system: A sustainable process for recovery of valuable metals from spent Li-ion batteries

A hydrometallurgical method involving natural organic acid leaching has been developed for recovery of lithium and cobalt from the cathode active materials in spent lithium-ion batteries. Succinic acid is employed as leaching agent and H2O2 as reductant. The cobalt and lithium contents from the succinic acid-based treatment of spent batteries are determined by inductively coupled plasma-optical emission spectroscopy to calculate the leaching efficiency. The spent LiCoO2 samples after calcination and the residues after leaching are characterized by X-ray diffraction and scanning electron microscopy. The results show that nearly 100% of cobalt and more than 96% of lithium are leached under optimal conditions: succinic acid concentration of 1.5 mol L-1, H2O2 content of 4 vol.%, solid-to-liquid ratio of 15 g L-1, temperature of 70 °C, and reaction time of 40 min. Results are also given for fitting of the experimental data to acid leaching kinetic models.

25 ENERGY STORAGE↗