Search NASA⌕ Search

Engineering topics

Zhang, Yubin

Publications and source records attributed to Zhang, Yubin.

At least 19 records

A Modified Sand’s Time Incorporating Li-Ion Transport Across the SEI: Basis for Understanding Li Dendrite Formation and Li-Metal Battery Electrolyte Selection

Abstract Understanding the initiation of lithium dendrites remains elusive, largely due to the intricate role of the solid electrolyte interphase (SEI) which forms on the Li surface during electrodeposition. Many studies have utilized the classical Sand’s equation to estimate the onset time when lithium dendrites begin to form. The Sand’s equation provides the time when the cation (Li+) concentration at the electrode-electrolyte interface approaches zero under diffusion-limited conditions in galvanostatic Li electrodeposition. However, recent experimental studies have revealed that the observed lithium dendrite onset time deviates considerably from the Sand’s time. Here, we show that this deviation from classical theory is likely due to the transport of Li+ ions through the SEI - a transport limitation that is much more dominant in controlling dendrite formation. We develop a ‘modified’ Sand's equation, incorporating the SEI layer and the diffusional transport across it to predict Li dendrite onset times. To validate this approach, we conducted Li electrodeposition experiments at various current densities using two distinct organic electrolytes. Analysis of the results demonstrates that the modified Sand's equation provides a more accurate prediction of dendrite onset times, highlighting the importance of incorporating SEI into transport models of Li plating in next-generation rechargeable Li-metal batteries.

Ma, Yuanman (ORCID:0000000200444811)↗

On the length scale and rate-dependent mechanical behavior of monolithic (oxy)sulfidic glassy solid-state electrolytes

In the controlled atmosphere of a dedicated glove box, nanoindentation performed with a diamond Berkovich indenter tip has been used to examine the mechanical behavior of three (oxy)sulfide solid-state electrolytes (SSEs), 70Li 2 S·(30–x)P 2 S 5 ·xP 2 O 5 (x = 0, 2, and 5). At a drive frequency of 120 Hz, the elastic modulus is found to be predominantly depth independent over the range of 100 nm to 1 μm and generally insensitive to the varying mol fraction of oxygen (0, 2, and 5%) as well as the imposed strain rates of 0.025, 0.05, and 0.1 1/s. All three SSEs exhibit significant room-temperature creep. Strain burst activity observed during loading (potentially representative of pore collapse or cracking) is attenuated with the addition of oxygen. The hardness is found to be insensitive to the imposed strain rates but varying with depth and oxygen content. Furthermore, the highest oxygen concentration yields the lowest hardness and strongest depth dependence.

36 MATERIALS SCIENCE↗

Improved Stability of Oxysulfide Solid-State Electrolytes in Li(G3)TFSI Solvate Ionic Liquid Electrolyte

The performance of all solid-state batteries is limited by poor interfacial contact between active material and solid-state electrolyte (SSE) particles. Semi-solid batteries utilize a secondary electrolyte phase to wet the SSE/AM interface to improve cell performance. Solvate ionic liquids (SILs) are one class of liquid electrolytes under consideration for use in semi-solid batteries. This paper focuses on the Li(G3)TFSI SIL consisting of the bis(trifluoromethanesulfonyl)imide (TFSI − ) anion coupled to a [Li(G3)] + solvate cation. Sulfide SSEs are normally subject to nucleophilic attack by trigylme (G3), however, strong coordination of Li + to G3 in the [Li(G3)] + solvate cation prevents this reaction from taking place. Consequently, the stability of sulfide SSE depends on the ideal 1:1 molar ratio of G3 to TFSI, which may be difficult to maintain. We studied the chemical stability of 70Li 2 S·(30-x)P 2 S 5 ·xP 2 O 5 (x = 0, 2, 5, 10) (oxy)sulfide solid-state electrolyte in Li(G3)TFSI SIL. By physical measurement, UV–vis spectroscopy, electrochemical evaluation, X-ray photoelectron spectroscopy, and first principles calculation it is shown that increased oxygen content improves the stability of SSE in various Li(G3) x TFSI (x = 1, 2, 3, 4) liquid electrolytes. The results suggest that an oxysulfide SSE + SIL semi-solid electrolyte is a good choice for future semi-solid battery designs.

Electrochemistry↗

Improved Thermal Stability of Oxysulfide Glassy Solid-State Electrolytes

In this study, the crystallization kinetics of (oxy)sulfide 70Li 2 S·(30-x)P 2 S 5 ·xP 2 O 5 (x = 0, 2, 5) solid-state electrolytes are reported. It was found that 5 mol% P 2 O 5 glass co-former slowed the crystallization rate of the Li 7 P 3 S 11−x/4 O x/4 ceramic phase by a factor of 10. After 10 min at 230 °C, a 70Li 2 S·30P 2 S 5 sulfide glass was 92% devitrified whereas a 70Li 2 S·25P 2 S 5 ·5P 2 O 5 oxysulfide glass was only 8% devitrified. The improved thermal stability of oxysulfide glasses was then utilized to demonstrate the fabrication of a standalone, reinforced SSE separator by hot pressing. More importantly, it was recognized that the microstructure of 70Li 2 S·25P 2 S 5 ·5P 2 O 5 oxysulfide SSE separators could be modified by hot pressing without changing ionic conductivity. This result was achieved because the precipitation of a superionically conductive Li 7 P 3 S 11−x/4 O x/4 ceramic phase was limited. A study was then conducted to determine what effect microstructure has on the susceptibility of SSE separators to shorting by lithium metal penetration. Hot-pressed separators were found to be more susceptible to shorting than cold-pressed separators. X-ray Computer Tomography (XCT) of post-mortem samples showed that hot-pressed samples failed by transverse microcrack pathways, which underscores the importance of low defect density in dense SSE separators.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

3D mapping of residual stresses in growing grains of partially recrystallized Gum Metal

The crystallographic orientations and residual stresses within recrystallizing grains in partially recrystallized beta titanium-Gum Metal-were examined non-destructively in 3D using synchrotron Differential Aperture X-ray Microscopy. Contrary to common assumptions, significant local stresses and stress variations are observed within the recrystallizing grains. The results reveal that the development of these local residual stresses depends on the plastic deformation mode and material's elastic constants, rather than grain properties such as size and orientation, or even the material's yield stress. This work provides insights valuable for the design of advanced materials with heterogeneous microstructures.

36 MATERIALS SCIENCE↗

Quantification of room temperature strengthening of laser shock peened Ni-based superalloy using synchrotron microdiffraction

Laser shock peening (LSP), a surface modification technique, is promising to enhance the strength and wear resistance for Ni-based superalloys. To understand the strengthening mechanism in a laser shock peened Ni-based superalloy DZ417G, we utilize synchrotron poly- and monochromatic X-ray microdiffraction, as well as electron microscopy and microhardness to quantify the local microstructures and mechanical properties at various depths. In the 1.2-mm-deep hardened layer, the microhardness increases monotonically by ~50% from the unaffected interior to the surface. Quantitative microdiffraction analysis shows that large amounts of dislocations are introduced by LSP. High densities of 7.1 × 10 15 m -2 and 11.8 × 10 15 m -2 are seen close to the peened surface for the γ- and γ'-phases, respectively, which are 5 and 20 times of those in the unaffected region. Different gradients of dislocation density are observed for the two phases from interior to surface, and their combined effect accounts well for the hardness increment. Due to the unaltered γ'-precipitates and chemical composition in the LSP affected zone, the large density of dislocations dominates the observed strengthening. Combined poly- and monochromatic X-ray microdiffraction allows quantifying the local microstructures of plastic deformation over a large sampling scale that can hardly be achieved using other materials characterization techniques.

36 MATERIALS SCIENCE↗

Local residual stresses and microstructure within recrystallizing grains in iron

The intragranular strains and the microstructure within recrystallizing grains in single phase pure iron have been systematically studied in 3D using synchrotron micro-diffraction. In contradiction to common knowledge we observe that residual elastic strains of up to 1–2 × 10 –3 are present in the recrystallizing grains. The local strain variations within individual grains can be similar in magnitude to those between different grains. The effects of processing parameters, including rolling reduction, recrystallized volume fraction, and cooling rate, as well as microstructural parameters, including grain size, orientation and internal misorientation, on the development of local residual elastic strains and microstructure have been quantified. It is suggested that the difference in local defect density between recrystallized grains and the surrounding deformed matrix, as well as the redistribution of medium to long-range residual stresses in the deformed grains, are the main reasons for the development of such strains in the recrystallized grains. The local residual stress levels are calculated and their possible impact on the mechanical properties and recrystallization processes are discussed.

36 MATERIALS SCIENCE↗

Moisture Stability of Sulfide Solid-State Electrolytes

In this report we detail a comprehensive study on the moisture stability of sulfide solid-state electrolytes in dry room environments. Although sulfide SSEs have many favorable attributes, this class of materials suffers from poor stability with water. Sulfide SSEs react with water to form gaseous H 2 S and a variety of solid byproducts like Li 3 PO 4 and LiOH, which go on to increase the interfacial impedance of solid-state batteries. Lab-scale research typically utilizes gloveboxes with <1 ppm water, however, the large-scale manufacturing of Li-ion batteries occurs in –40°C dewpoint dry rooms with around 126 ppm water. Consequently, the moisture stability of sulfide SSEs must be addressed if the manufacture of solid-state batteries based on sulfide SSEs is to be scaled up. Here, we are the first to characterize the moisture stability of sulfide SSEs according to both H 2 S and the degradation of ionic conductivity at different moisture setpoints ranging from –76°C to –40°C dewpoint. A variety of different SSE compositions are studied; namely, (Li 2 S) 75 (P 2 S 5 ) 25 , (Li 2 S) 70 (P 2 S 5 ) 30 , (Li 2 O) 7 (Li 2 S) 68 (P 2 S 5 ) 25 , (Li 2 O) 7 (Li 2 S) 63 (P 2 S 5 ) 30 , and (Li 2 S) 75 (P 2 S 5 ) 25 + 20 mol% LiI. We find that moisture stability improves with 75 mol% Li2S modifier content and the introduction of a Li 2 O co-modifier. After a 30 min exposure in a –40°C dewpoint dry room environment we found that (Li 2 S) 75 (P 2 S 5 ) 25 + 20 mol% LiI powder generated 0.1 cc/g H 2 S and its ionic conductivity decreased by over 50%. However, when SSE powder was exposed as a slurry in a dodecane carrier the same SSE composition generated 0 cc/g H 2 S and its ionic conductivity only dropped by 14%. Our results show that sulfide SSEs have acceptable moisture stability when appropriately processed in a dry room environment.

25 ENERGY STORAGE↗

Self-Stabilized LiNi 0.8 Mn 0.1 Co 0.1 O 2 in thiophosphate-based all-solid-state batteries through extra LiOH

Nickle-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC 811) cathode material exhibits engaging properties in high energy density and low cost, making it great potential for the next generation high-energy all-solid-state lithium batteries (ASSLBs). However, NMC 811 suffers from severe surface electrochemical, chemical, and voltage incompatibility towards solid-state electrolytes (SSE), especially thiophosphate-based electrolytes like Li 6 PS 5 Cl. Although diverse coating methods have been made to overcome this issue, they are typically cumbersome and expensive. A coating strategy that satisfied all the requirements of cost-efficiency, stability, uniformity, scalability, and easy-achieving is still challenging. Here, we developed a LiOH-based surface stabilization strategy that provides a ~10 nm stable permeable layer on NMC 811. After one-step sintering of NMC 811 precursor mixed with LiOH, which is commonly used for NMC 811 lithiation process, excessive LiOH simultaneously distributes on NMC 811 particles. Unlike other reported methods, this coating method can be easily controlled and fabricated without additional complicated processes. By simply controlling the thickness of LiOH layer, which protects the Li 6 PS 5 Cl solid electrolyte materials from being oxidized, optimized cycling stability can be obtained for 600 cycles with capacity of 130 mAh g – 1 on average at a wide electrochemical window of 2.50–4.20 V (vs. Li-In).

25 ENERGY STORAGE↗

In Situ Synchrotron X-ray Micro-Diffraction Investigation of Elastic Strains in Laminated Ti-Al Composites

Spatially resolved elastic strains in the bulk interior of a laminated Ti-Al metal composite were studied during in situ tensile loading at strains up to 1.66% by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM). For both Al and Ti grains, deviatoric elastic strains were estimated based on polychromatic X-ray microbeam diffraction, while lattice strains along the normal direction of the tensile sample were directly measured using monochromatic X-ray microbeam diffraction. The estimated deviatoric strains show large spatial variations, and the mean values are consistent with the external loading conditions, i.e., increasing tensile strain along the tensile direction and increasing compressive strain along the sample normal with increasing loading. The directly measured lattice strains also show large spatial variations, although the magnitude of this variation is smaller than that for the estimated deviatoric strain. The directly measured lattice strains in Ti grains are largely consistent with the external loading, whereas those in Al grains are in contradiction with the external loading. The causes of the experimental results are discussed and related to both the laminated microstructure of the composite material and the limitations of the techniques.

36 MATERIALS SCIENCE↗

Residual strain-stress in manganese steel railway crossing determined by synchrotron and laboratory X-rays

The residual stress within the nose of a worn manganese steel railway crossing was investigated. The macroscopic residual stress at the running surface was determined in areas with and without visual faults by laboratory X-rays. To get information about the penetration depth of the residual stress, synchrotron X-ray diffraction was used to map the distribution of local (within grain) residual strains below the running surface. The laboratory X-ray measurements revealed significant compressive stress on the rail running surface. The synchrotron measurements documented that local strains exist through the entire depth investigated. Relations between residual stress, plastic deformation, and crack formation are analysed, leading to a discussion on potentials/limitations of the two experimental methods for investigations of residual stress in large engineering components.

differentia aperture synchrotron diffraction↗

In-situ synchrotron X-ray micro-diffraction investigation of ultra-low-strain deformation microstructure in laminated Ti-Al composites

An ultra-low-strain deformation microstructure was revealed for the first time non-destructively in the bulk interior of an annealed laminated Ti-Al composite-in the "fully recrystallized" Al layer-by a synchrotron-based micro-diffraction technique, namely differential aperture X-ray microscopy (DAXM), through real space mapping with a very high angular resolution (0.01 degrees). This ultra-low-strain deformation microstructure was found to result from the thermal stress, induced during cooling after annealing, due to the different coefficients of thermal expansion for the Ti and Al layers. The annealed sample was further tensile deformed to a strain of 1.66% and followed by in situ DAXM and analyzed by various misorientation mapping methods. The results pointed to the important effects of the initial microstructure and the interface constraint, as well as the grain size and crystal orientation, on the plastic deformation. A gradient in dislocation density from the layer interface to the center was found in the Al layer of the annealed sample, and this gradient increased slightly during tensile deformation. The variation of the dislocation density was further discussed based on the activation and interaction of dislocations in grains of different sizes and orientations during plastic deformation. The findings of this study provided valuable insights in understanding the constraint effect of the laminated metal composite and the design of novel composite materials. (c) 2020 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Crystallographic orientation↗

Polymer–Ceramic Composite Electrolytes for Lithium Batteries: A Comparison between the Single-Ion-Conducting Polymer Matrix and Its Counterpart

Single-ion-conducting polymer electrolytes are attractive to use in lithium batteries as the transference number of the lithium cation approaches unity. This helps prevent concentration gradients across the electrolyte, which can result in dendrite formation. The addition of ceramic particles to polymer electrolytes at high loadings can increase the mechanical strength of the polymer, which can also help suppress dendrite formation. Here, a single-ion-conducting polymer electrolyte is blended with lithium-conducting oxide ceramic particles to make a composite electrolyte. This electrolyte is studied in comparison to a composite electrolyte containing freely dissolved lithium salt. It is found that the addition of ceramic particles to the single-ion-conducting polymer can result in increased cation dissociation and consequent increased ionic conductivity. The electrolytes are cycled in lithium symmetrical cells, and it is found that the ceramic-containing electrolytes show increased interfacial stability with the lithium metal compared to the pristine polymer electrolytes. Our findings shed light on how to optimize the polymer host chemistry to form composite electrolytes that can meet the challenging requirements to stabilize the lithium metal anode.

25 ENERGY STORAGE↗

Alignment of sample position and rotation during in situ synchrotron X-ray micro-diffraction experiments using a Laue cross-correlation approach

Laue micro-diffraction has proven to be able to reveal material properties at the sub-grain scale for many polycrystalline materials and is now routinely available at several synchrotron facilities, providing an approach for nondestructive three-dimensional probing of the microstructures and mechanical states of materials. However, for in situ experiments, maintaining the positioning of the sample throughout the experiment, to achieve a good alignment of the characterized volumes, is a challenging issue. The aim of the present work is to address this problem by developing an approach based on digital image correlation of focused-beam Laue diffraction patterns. The method uses small changes in the diffraction signal as a focused X-ray beam is scanned over a surface region to allow corrections to be made for both sample lateral movement and rotation. The method is demonstrated using a tensile deformation experiment on an Al sample with 2.5 µm average grain size. The results demonstrate an accuracy of 0.5 µm for sample position registration and a precision in sample rotation of ~0.01°. Finally, the proposed method is fast to implement and does not require the use of additional surface markers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗