Search NASA⌕ Search

Engineering topics

Zhang, Yugang

Publications and source records attributed to Zhang, Yugang.

54 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Extremely Slow Diffusion of Gold Nanoparticles under Confinement in Mesoporous Silica

Here, we report an X-ray photon correlation spectroscopy (XPCS) study of the mobility of colloidal gold nanoparticles with a diameter of approximately 4 nm in glycerol under confinement within the channels of SBA-15 mesoporous silica with pore diameters of approximately 6 and 12 nm. The XPCS correlation functions result from an effective heterodyne signal due to the mixing of the coherent scattering from the nanoparticles and the mesoporous silica. Over the range of wave vectors and hence length scales probed, the nanoparticle dynamics are well described by one-dimensional diffusion. The nanoparticle diffusivity varies with temperature in a manner expected based on the temperature-dependent viscosity of glycerol; however, the magnitudes of the diffusion coefficients are several orders of magnitude smaller than those of the nanoparticles in bulk glycerol. We consider mechanisms that might contribute to this reduction in diffusivity including enhancement in hydrodynamic drag under confinement, effects of nanoparticle adsorption to the pore walls, and slowing structural dynamics in glycerol due to the combination of the nanometer-scale confinement and the presence of the nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dual‐Ion Intercalation and High Volumetric Capacitance in a Two‐Dimensional Non‐Porous Coordination Polymer

Abstract Intercalation is a promising ion‐sorption mechanism for enhancing the energy density of electrochemical capacitors (ECs) because it offers enhanced access to the electrochemical surface area. It requires a rapid transport of ions in and out of a host material, and it must occur without phase transformations. Materials that fulfil these requirements are rare; those that do intercalate almost exclusively cations. Herein, we show that Ni 3 (benzenehexathiol) (Ni 3 BHT), a non‐porous two‐dimensional (2D) layered coordination polymer (CP), intercalates both cations and anions with a variety of charges. Whereas cation intercalation is pseudocapacitive, anions intercalate in a purely capacitive fashion. The excellent EC performance of Ni 3 BHT provides a general basis for investigating similar dual‐ion intercalation mechanisms in the large family of non‐porous 2D CPs.

Banda, Harish↗
DOE OSTI2021

The damping of terahertz acoustic modes in aqueous nanoparticle suspensions

In this work, we investigate the possibility of controlling the acoustic damping in a liquid when nanoparticles are suspended in it. To shed light on this topic, we performed Inelastic X-Ray Scattering (IXS) measurements of the terahertz collective dynamics of aqueous suspensions of nanospheres of various materials, size, and relative concentration, either charged or neutral. A Bayesian analysis of measured spectra indicates that the damping of the two acoustic modes of water increases upon nanoparticle immersion. This effect seems particularly pronounced for the longitudinal acoustic mode, which, whenever visible at all, rapidly damps off when increasing the exchanged wavevector. Results also indicate that the observed effect strongly depends on the material the immersed nanoparticles are made of.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dual-Ion Intercalation and High Volumetric Capacitance in a Two-Dimensional Non-Porous Coordination Polymer

Intercalation is a promising ion-sorption mechanism for enhancing the energy density of electrochemical capacitors (ECs) because it offers enhanced access to the electrochemical surface area. It requires a rapid transport of ions in and out of a host material, and it must occur without phase transformations. Materials that fulfil these requirements are rare; those that do intercalate almost exclusively cations. Herein, we show that Ni3(benzenehexathiol) (Ni 3 BHT), a non-porous two-dimensional (2D) layered coordination polymer (CP), intercalates both cations and anions with a variety of charges. Whereas cation intercalation is pseudocapacitive, anions intercalate in a purely capacitive fashion. The excellent EC performance of Ni3BHT provides a general basis for investigating similar dual-ion intercalation mechanisms in the large family of non-porous 2D CPs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nanoscale dynamics during self-organized ion beam patterning of Si. I. Ar + bombardment

X-ray photon correlation spectroscopy (XPCS) is used to investigate the fluctuation dynamics during self- organized nanopatterning of silicon by Ar + bombardment at 65° polar angle. Rich structure is observed in the development of the correlation dynamics as seen in the evolving correlation time τ(q || ) and fluctuation relaxation exponent n(q || ). Furthermore, on length scales of the ripple structure, local structure becomes ever more long lived as coarsening progresses. In addition, τ (q || ) develops a peak on length scales corresponding to the ripple wavelength. As patterning progresses, correlation times become asymmetric between the positive and negative directions, suggesting the possibility of different dynamics on the slopes facing toward and away from the ion beam. Relaxation exponents show evolution from linear dynamics at early times to compressed exponential relaxation at low wave numbers and stretched exponential relaxation at high wave numbers. Compressed exponential behavior is reminiscent of stress relaxation processes observed in glasses.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Nanoscale dynamics during self-organized ion beam patterning of Si. II. Kr + bombardment

Understanding the self-organized ion beam nanopatterning of elemental semiconductors, particularly silicon, is of intrinsic scientific and technological interest. This is the second component of a two-part coherent x-ray scattering and x-ray photon correlation spectroscopy (XPCS) investigation of the kinetics and fluctuation dynamics of nanoscale ripple development on silicon during 1 keV Ar + (part I) and Kr + bombardment at 65° polar angle. Here it is found that the ion-enhanced viscous flow relaxation is essentially equal for Kr + -induced patterning as previously found for Ar + patterning despite the difference in ion masses. However, the magnitude of the surface curvature-dependent roughening rate in the early-stage kinetics is larger for Kr + than for Ar + , consistent with expectations that the heavier ion gives an increased mass redistributive contribution to the initial surface instability. As with the Ar + case, fluctuation dynamics in the late stage show a peak in correlation times at the length scale corresponding to the dominant structural feature on the surface—the ripples. Finally, it is shown that speckle motion during the surface evolution can be analyzed to determine spatial inhomogeneities in erosion rate and ripple velocity. This allows the direction and speed of ripple motion to be measured in a real time experiment. In the present case, ripple motion is found to be into the projected direction of the ion source, in contrast to expectations from an existing sputter erosion driven model with parameters derived from binary collision approximation simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2021

XPCS Microrheology and Rheology of Sterically Stabilized Nanoparticle Dispersions in Aprotic Solvents

In this study, X-ray photon correlation spectroscopy (XPCS) microrheology and conventional bulk rheology were performed on silica nanoparticle dispersions associated with battery electrolyte applications to probe the properties of these specific complex materials and to explore the utility of XPCS microrheology in characterizing nanoparticle dispersions. Sterically stabilized shear-thickening electrolytes were synthesized by grafting poly(methyl methacrylate) chains onto silica nanoparticles. Coated silica dispersions containing 5–30 wt % nanoparticles dispersed in propylene carbonate were studied. In general, both XPCS microrheology and conventional rheology showed that coated silica dispersions were more viscous at higher concentrations, as expected. The complex viscosity of coated silica dispersions showed shear-thinning behavior over the frequency range probed by XPCS measurements. However, measurements using conventional mechanical rheometry yielded a shear viscosity with weak shear-thickening behavior for dispersions with the highest concentration of 30% particles. Our results indicate that there is a critical concentration needed for shear-thickening behavior, as well as appropriate particle size and surface polymer chain length, for this class of nanoparticle-based electrolytes. The results of this study can provide insights for comparing XPCS microrheology and bulk rheology for related complex fluids and whether XPCS microrheology can capture expected macroscopic rheological properties by probing small-scale particle dynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

de Gennes Narrowing and Relationship between Structure and Dynamics in Self-Organized Ion-Beam Nanopatterning

Investigating the relationship between structure and dynamical processes is a central goal in condensed matter physics. Perhaps the most noted relationship between the two is the phenomenon of de Gennes narrowing, in which relaxation times in liquids are proportional to the scattering structure factor. Here, a similar relationship is discovered during the self-organized ion-beam nanopatterning of silicon using coherent x-ray scattering. However, in contrast to the exponential relaxation of fluctuations in classic de Gennes narrowing, the dynamic surface exhibits a wide range of behaviors as a function of the length scale, with a compressed exponential relaxation at lengths corresponding to the dominant structural motif—self-organized nanoscale ripples. These behaviors are reproduced in simulations of a nonlinear model describing the surface evolution. Our team suggests that the compressed exponential behavior observed here is due to the morphological persistence of the self-organized surface ripple patterns which form and evolve during ion-beam nanopatterning.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Techniques to characterize dynamics in biomaterials microenvironments: XPCS and microrheology of alginate/PEO–PPO–PEO hydrogels

Many recent studies have highlighted the timescale for stress relaxation of biomaterials on the microscale as an important factor in regulating a number of cell-material interactions, including cell spreading, proliferation, and differentiation. Relevant timescales on the order of 0.1–100 s have been suggested by several studies. While such timescales are accessible through conventional mechanical rheology, several biomaterials have heterogeneous structures, and stress relaxation mechanisms of the bulk material may not correspond to that experienced in the cellular microenvironment. Here we employ X-ray photon correlation spectroscopy (XPCS) to explore the temperature-dependent dynamics, relaxation time, and microrheology of multicomponent hydrogels comprising of commercial poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) (PEO–PPO–PEO) triblock copolymer F127 and alginate. Previous studies on this system have shown thermoreversible behavior in the bulk oscillatory shear rheology. At physiological temperatures, bulk rheology of these samples shows behavior characteristic of a soft solid, with G' > G" and no crossover between G' and G" over the measurable frequency range, indicating a relaxation time >125 s. By contrast, XPCS-based microrheology shows viscoelastic behavior at low frequencies, and XPCS-derived correlation functions show relaxation times ranging from 10–45 s on smaller length scales. Finally, we are able to use XPCS to effectively probe the viscoelasticity and relaxation behavior within the material microenvironments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic clay microstructures emerge via ion complexation waves

Clays control carbon, water and nutrient transport in the lithosphere, promote cloud formation5 and lubricate fault slip through interactions among hydrated mineral interfaces. Clay mineral properties are difficult to model because their structures are disordered, curved and dynamic. Consequently, interactions at the clay mineral-aqueous interface have been approximated using electric double layer models based on single crystals of mica and atomistic simulations. We discover that waves of complexation dipoles at dynamically curving interfaces create an emergent long-range force that drives exfoliation and restacking over time- and length-scales that are not captured in existing models. Curvature delocalizes electrostatic interactions in ways that fundamentally differ from planar surfaces, altering the ratio of ions bound to the convex and concave sides of a layer. Multiple-scattering reconstruction of low-dose energy-filtered cryo electron tomography enabled direct imaging of ion complexes and electrolyte distributions at hydrated and curved mineral interfaces with {\aa}ngstrom resolution over micron length scales. Layers exfoliate and restack abruptly and repeatedly over timescales that depend strongly on the counterion identity, demonstrating that the strong coupling between elastic, electrostatic and hydration forces in clays promote collective reorganization previously thought to be a feature only of active matter.

Whittaker, Michael L↗
DOE OSTI2020

Measurement of Ehrlich-Schwoebel barrier contribution to the self-organized formation of ordered surface patterns on Ge(001)

Normal-incidence 1-keV Ar + ion bombardment leads to amorphization and ultrasmoothing of Ge at room temperature, but at elevated temperatures the Ge surface remains crystalline and is unstable to the formation of self-organized nanoscale patterns of ordered pyramid-shaped pits. The physical phenomenon distinguishing the high-temperature patterning from room-temperature ultrasmoothing is believed to be a surface instability due to the Ehrlich-Schwoebel barrier for diffusing vacancies and adatoms, which is not present on the amorphous material. This real-time grazing-incidence small-angle x-ray scattering study compares smoothing of a prepatterned Ge sample at room temperature with patterning of an initially flat Ge sample at an elevated temperature. In both experiments, when the nanoscale structures are relatively small in height, the average kinetics can be explained by a linear theory. Furthermore, the linear theory coefficients, indicating surface stability or instability, were extracted for both experiments. A comparison between the two measurements allows estimation of the contribution of the Ehrlich-Schwoebel barrier to the self-organized formation of ordered nanoscale patterns on crystalline Ge surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Domain fluctuations in a ferroelectric low-strain BaTiO 3 thin film

In this work, a ferroelectric BaTiO 3 thin film grown on a NdScO 3 substrate was studied using x-ray photon correlation spectroscopy (XPCS) to characterize thermal fluctuations near the a/b to a/c domain structure transformation present in this low-strain material, which is absent in the bulk. XPCS studies provide a direct comparison of the role of domain fluctuations in first- and second-order phase transformations. The a/b to a/c domain transformation is accompanied by a decrease in fluctuation timescales, and an increase in intensity and correlation length. Surprisingly, domain fluctuations are observed up to 25 °C above the transformation, concomitant with the growth of a/c domains and coexistence of both domain types. After a small window of stability, as the Curie temperature is approached, a/c domain fluctuations are observed, albeit slower, potentially due to the structural transformation associated with the ferroelectric to paraelectric transformation. The observed time evolution and reconfiguration of domain patterns highlight the role played by phase coexistence and elastic boundary conditions in altering fluctuation timescales in ferroelectric thin films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

99 TcO 4 - removal from legacy defense nuclear waste by an alkaline-stable 2D cationic metal organic framework

Removal of 99 TcO 4 - from legacy defense nuclear tank waste at Savannah River Site is highly desirable for the purpose of nuclear safety and environmental protection, but currently not achievable given the extreme conditions including high alkalinity, high ionic strength, and strong radiation field. Herein, we present a potential solution to this long-term issue by developing a two-dimensional cationic metal organic framework SCU-103, showing ultrahigh stability in alkaline aqueous media and great resistance to both β and γ radiation. More importantly, it is very effective for 99 TcO 4 - separation from aqueous media as demonstrated by fast exchange kinetics, high sorption capacity, and superior selectivity, leading to the successful removal of 99 TcO 4 - from actual Savannah River Site high level tank waste for the first time, to the best of our knowledge. In addition, the uptake mechanism is comprehensively elucidated by molecular dynamics simulation and density functional theory calculation, showing a unique chemical recognition of anions with low charge density.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2020

In-Operando Study of Shape Retention and Microstructure Development in a Hydrolyzing Sol–Gel Ink during 3D-Printing

3D printing of amorphous and crystalline ceramics is of paramount importance for the fabrication of a wide range of devices with applications across different technology fields. Printed ceramics are remarkably enabled by the sol-gel synthesis method in conjunction with continuous filament direct ink writing. During printing, multiple processes contribute to the evolution of inks including shape retention, chemical conversion, solidification, and microstructure formation. Traditionally, depending on the ink composition and printing environment, several mechanisms have been associated with the shape retention and solidification of 3D printed structures: gelation, rapid solvent evaporation, energy-driven phase transformation, and chemical-driven phase transformation. Understanding the fundamental differences between these mechanisms becomes key since they strongly influence the spatiotemporal evolution of the materials, as the out-of-equilibrium processes inherent to the extrusion, relaxation, and solidification of printed materials have significant effects on the materials properties. Herein, we investigate the shape retention mechanism and the hydrolysis-induced material conversion and microstructure formation during the 3D printing of a water reactive sol-gel ink that transforms into titanium dioxide-based ceramic. This study aims at identifying characteristic mechanisms associated with the material transformation, establishing connections between the microstructure development and the timescales associated with solidification under operando 3D-printing conditions. The investigation of this material's out-of-equilibrium pathways under processing conditions is enabled by time-resolved coherent X-ray scattering, providing simultaneous access to temporospatially resolved microstructural and dynamics information. Furthermore, we explore X-ray speckle tracking as a tool to resolve deformations of the microstructure in a printed filament associated with the deposition of consecutive filaments. Through this work, we aim at providing a fundamental understanding of the relationships behind these transformative processes in 3D printing and their timescales as the basis for achieving unprecedented control over printed materials microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamics at the crystal-melt interface in a supercooled chalcogenide liquid near the glass transition

Direct quantitative measurements of nanoscale dynamical processes associated with structural relaxation and crystallization near the glass transition are a major experimental challenge. These type of processes have been primarily treated as macroscopic phenomena within the framework of phenomenological models and bulk experiments. Here, we report x-ray photon correlation spectroscopy measurements of dynamics at the crystal-melt interface during the radiation induced formation of Se nano-crystallites in pure Se and in binary AsSe 4 glass-forming liquids near their glass transition temperature. We observe a heterogeneous dynamical behaviour where the intensity correlation functions g 2 (q, t) exhibits either a compressed or a stretched exponential decay, depending on the size of the Se nano-crystallites. The corresponding relaxation timescale for the AsSe 4 liquid increases as the temperature is raised, which can be attributed to changes in the chemical composition of the melt at the crystal-melt interface with the growth of the Se nano-crystallites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ultrastructures and Mechanics of Annealed Nephila clavipes Major Ampullate Silk

The semicrystalline protein structure and impressive mechanical properties of major ampullate (MA) spider silk make it a promising natural alternative to polyacrylonitrile (PAN) fibers for carbon fiber manufacture. However, when annealed using a similar procedure to carbon fiber production, the tensile strength and Young’s modulus of MA silk decrease. Despite this, MA silk fibers annealed at 600 °C remain stronger and tougher than similarly annealed PAN but have a lower Young’s modulus. Although MA silk and PAN graphitize to similar extents, annealing disrupts the hydrogen bonding that controls crystal alignment within MA silk. Consequently, unaligned graphite crystals form in annealed MA silk, causing it to weaken, while graphite crystals in PAN maintain alignment along the fiber axis, strengthening the fibers. Finally, these shortcomings of spider silk when annealed provide insights into the selection and design of future alternative carbon fiber precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Nanoscale viscosity of confined polyethylene oxide

Complex fluids near interfaces or confined within nanoscale volumes can exhibit substantial shifts in physical properties compared to bulk, including glass transition temperature, phase separation, and crystallization. Because studies of these effects typically use thin film samples with one dimension of confinement, it is generally unclear how more extreme spatial confinement may influence these properties. In this work, we used x-ray photon correlation spectroscopy and gold nanoprobes to characterize polyethylene oxide confined by nanostructured gratings (<100nm width) and measured the viscosity in this nanoconfinement regime to be ~500 times the bulk viscosity. Here, this enhanced viscosity occurs even when the scale of confinement is several times the polymer's radius of gyration, consistent with previous reports of polymer viscosity near flat interfaces.

36 MATERIALS SCIENCE↗