Exploring irradiated granular flows with rapid heating for concentrated solar thermal energy collection and storage
Not Available
Jeong, Shin Young (ORCID:0000000347897129)↗
Engineering topics
Zhang, Zhuomin M.
Publications and source records attributed to Zhang, Zhuomin M..
A numerical study of the spectral radiative properties of packed bed with mixed bauxite and silica spheres
Bauxite and silica particles have gained increasing attention for applications in the field of concentrated solar power. In this work, a Monte Carlo ray-tracing simulation is performed to predict the radiative properties (absorptance, reflectance, and transmittance) of packed beds with mixed bauxite and silica spherical particles at wavelengths of 0.5, 2.6, 9.0, and 9.35 µm. These wavelengths are representative for the visible, near-infrared, and the mid-infrared regions that are important for solar and thermal radiation, respectively. A repeating unit-column approach is used to mathematically represent the particle bed. The effects of particle mixing ratio, volume fraction, and wavelength on the predicted radiative properties are examined. The obtained radiative properties are inputted to an inverse method to retrieve the effective absorption and scattering coefficients as well as the scattering albedo, which may be later used in a continuous-scale radiative heat transfer analysis. Furthermore, the independent scattering model is used to obtain the absorption coefficient and scattering albedo based on the absorption and scattering cross sections predicted by a Monte Carlo algorithm for a single particle. It is shown that the independent scattering model underpredicts the scattering coefficient for opaque particles but overpredicts the scattering coefficient for semitransparent particles for sufficiently high particle volume fractions. Here, the radiative properties calculated from the independent scattering model are compared to the full Monte Carlo simulation of the particle bed to examine the influence of particle mixing on dependent scattering.
42 ENGINEERING↗
Thermoradiative devices enabled by hyperbolic phonon polaritons at nanoscales
Not Available
Feng, Dudong↗
Experimental characterization of extreme temperature granular flows for solar thermal energy transport and storage
High-temperature, dense granular flows along an inclined plane were considered for solar thermal energy transport and storage with sintered bauxite particles. A series of experiments was performed for particle inlet temperatures of ~ 200, 400, 600, and 800 °C to understand the mechanisms of granular flows at extreme temperatures. Mass flow rates were measured using a load cell and free-surface velocities were measured and computed using particle image velocimetry. Surface temperatures were measured using infrared cameras. A significant decrease in steady-state particle mass flow rate was observed with increasing temperature due to changing flow properties. A decrease in bulk particle free-surface velocities was observed at higher temperatures. Free-surface velocity measurement error between experiments were within 20% of the average. The particle surface temperatures decreased from inlet to outlet with larger gradients at higher temperatures observed due to increasing convection and radiative heat losses. Here, a decrease in temperature was observed along the side walls due to a decrease in particle velocities.
14 SOLAR ENERGY↗
Geometric and doping effects on radiative recombination in thin-film near-field energy converters
Modeling radiative recombination is crucial to the analysis of radiative energy converters. In this work, a local radiative recombination coefficient is defined and derived based on fluctuational electrodynamics that is applicable to thin-film cells in both the near field and far field. The predicted radiative recombination coefficient of an InAs cell deviates from the van Roosbroeck–Shockley relation when the thickness is less than 10 µm, and the difference exceeds fourfold with a 10 nm film. The local radiative recombination coefficient is orders of magnitude higher when an InAs cell is configured in the near field. The local radiative recombination coefficient reduces as the doping level approaches that of a degenerate semiconductor. The maximum output power and efficiency of a thermoradiative cell would be apparently overpredicted if the electroluminescence coefficient defined in this paper were taken as unity for heavily doped semiconductors.
Feng, Dudong↗
Temperature-dependent spectral emittance of bauxite and silica particle beds
Bauxite and silica particles are candidate materials for solar thermal energy storage at high temperatures. The temperature-dependent emittance of packed beds with bauxite and silica particles was measured using a newly upgraded emissometer at wavelengths 2 μm ≤ λ ≤ 16 μm and temperatures up to ~730 K. The room-temperature emittance was obtained from the measured directional-hemispherical reflectance. A fused silica disc was used to test the emissometer by comparing the measured spectral emittance with the calculated emittance from a fitted Lorentz oscillator model. For the polycrystalline silica particles and the fused silica disc, the measured emittance increases with temperature in the mid-infrared region. The underlying mechanism is interpreted as the temperature-dependent damping coefficient in the Lorentz oscillator model. Two types of bauxite particles with different compositions and sizes were investigated. For λ > 10 μm, the measured emittance at elevated temperatures is higher than that at room temperature. In the region 2 μm < λ < 6 μm, the temperature dependence varies for different types of particles. The total emittance of bauxite particle beds was calculated by spectral integration using Planck’s distribution at the prescribed temperature. As a result, the calculated total emittance is between 0.89 and 0.96, but it does not change monotonically with temperature.
42 ENGINEERING↗
Spectral Radiative Properties of Polydispersed SiO 2 Particle Beds
The focus of this work is on the measurement and analysis of the radiative properties of polycrystalline SiO 2 particle beds with various layer thicknesses. The particles are polydispersed with average diameters of 222, 150, and 40 μm . The spectral, directional–hemispherical reflectance and transmittance of the particle bed are measured at wavelengths from 0.4 to 1.8 μm using a monochromator, and the reflectance measurement is extended to 15 μm using a Fourier-transform infrared spectrometer. Particles are closely packed between two transparent windows for measuring the radiative properties. In the visible and near-infrared region up to 1.8 μm, the inverse adding–doubling method yields the effective absorption and scattering coefficients. The results suggest that short wavelength absorption needs to be included in modeling the behavior of particle beds due to multiple scattering. A discrete-scale Monte Carlo ray-tracing method is developed to model the radiative properties by assuming monodispersed spherical particles, and the simulated results compare well with measurements. The effective absorption and scattering coefficients of the particle beds obtained from the independent scattering theory are compared to those from the inverse method. As a result, the impact of dependent scattering on the packed beds is observed for smaller-sized particles.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
Improved performance of a near-field thermophotovoltaic device by a back gapped reflector
Various spectral control techniques can be applied to improve the performance of a thermophotovoltaic (TPV) device. For example, a back surface reflector (BSR) is a common structure to improve the performance of TPV devices. A conventional metal BSR structure enhances the photogeneration rate by increasing the absorption probability of photons via back surface reflections, affording a second chance for absorption. However, the effects of surface passivation and external luminescence introduced by BSR structures have been previously ignored, which potentially decreases the performance of TPV devices. Recently, a back gapped reflector (BGR) structure was proposed to greatly improve the performance of far-field TPV devices by reducing imperfect reflections at the semiconductor-metal interface. In the present work, the performance improvement on a thin-film, near-field InAs TPV device with a BGR is investigated, comparing its performance to that with a conventional metal BSR. Surface passivation conditions are also investigated to further improve the performance of TPV devices with back reflectors. Further, the output power and efficiency are calculated using an iterative model combining fluctuational electrodynamics and the full drift diffusion model. For the well-passivated condition, when the BSR is replaced by the BGR, the calculated conversion efficiency of the near-field TPV was improved from 16.4% to 21% and the output power was increased by 10%. Finally, the absorption of the back reflectors and external luminescence loss are analyzed to explain the performance improvement.
external luminescence↗
Near-field photonic thermal diode based on hBN and InSb films
A thermal diode is a two-terminal device that allows heat to transfer more easily in one direction (forward bias) than in the opposite direction (reverse bias). A photonic thermal diode operates in a contactless mode and may afford a large operating temperature range. Here, a near-field photonic thermal diode based on hexagonal boron nitride (hBN) and indium antimonide (InSb) films is theoretically demonstrated. In this work, the temperature dependence of the interband absorption of InSb is used to couple (or decouple) with the hyperbolic phonon polaritons in hBN. The numerical analysis predicts a rectification ratio greater than 17 for a 10 nm vacuum gap, when operating at an average temperature of 300 K and a temperature difference of 200 K. The calculated rectification ratio exceeds 35 at higher average temperatures with larger temperature differences.
77 NANOSCIENCE AND NANOTECHNOLOGY↗
Measurements of scattering and absorption properties of submillimeter bauxite and silica particles
Submillimeter solid particles have been considered as thermal storage media for concentrated solar power applications. Knowledge of the scattering and absorption properties of individual particles is crucial for modeling the radiative heat transfer of the particle bed. In this work, a laser scatterometer is used to measure the single-particle scattering properties at a wavelength of 635 nm by using two configurations: (1) a falling particle curtain and (2) a taped particle layer. Because a one-particle nominal thickness is formed with area fractions of 5-55% depending on the configuration, multiple scattering is minimized and hence the single scattering phase function, averaged over all illuminated particles, is directly measured. Bauxite-based ceramic particles that are strongly absorbing in the solar spectrum and silica particles that are nonabsorbing in the visible and near-infrared are investigated. The directional-hemispherical reflectance and transmittance of the taped particles are also measured to deduce the forward and backward scattering efficiency factors and the absorption efficiency factors. Only weak wavelength dependence is observed in the measured region from 380 nm to 1020 nm. Furthermore, the scattering phase functions of all bauxite-based particles with varying sizes and compositions are very similar and can be fitted to a Henyey-Greenstein phase function with an asymmetry factor g = -0.20. For the silica particles, forward scattering dominates and g = 0.45 yields the best fit. A Monte Carlo method is developed to model the particle scattering characteristics, and reasonable agreements between the modeling and experimental results are observed by introducing a specularity parameter.
42 ENGINEERING↗
Spatial profiles of photon chemical potential in near-field thermophotovoltaic cells
Emitted photons stemming from the radiative recombination of electron–hole pairs carry chemical potential in radiative energy converters. This luminescent effect can substantially alter the local net photogeneration in near-field thermophotovoltaic cells. Several assumptions involving the luminescent effect are commonly made in modeling photovoltaic devices; in particular, the photon chemical potential is assumed to be zero or a constant prescribed by the bias voltage. The significance of photon chemical potential depends upon the emitter temperature, the semiconductor properties, and the injection level. Hence, these assumptions are questionable in near-field thermophotovoltaic devices with nanoscale separation distances between the emitter and the cell. In the present work, an iterative solver that combines fluctuational electrodynamics with the drift-diffusion model is developed to tackle the coupled photon and charge transport problem, enabling the determination of the spatial profile of photon chemical potential beyond the detailed balance approach. Here, the difference between the results obtained by allowing the photon chemical potential to vary spatially and by assuming a constant value demonstrates the limitations of the conventional approaches. This study is critically important for performance evaluation of near-field thermophotovoltaic systems with nanoscale vacuum gaps.
30 DIRECT ENERGY CONVERSION↗
Coupled Charge and Radiation Transport Processes in Thermophotovoltaic and Thermoradiative Cells
Accurate modeling of charge transport and both thermal and luminescent radiation is crucial to the understanding and design of radiative thermal energy converters. Charge-carrier dynamics in semiconductors are well-described by the Poisson-drift-diffusion equations, and thermal radiation in emitter-absorber structures can be computed using multilayer fluctuational electrodynamics. These two types of energy flows interact through radiation absorption or luminescence and charge-carrier generation or recombination. However, past research has typically only assumed limited interaction, with thermal radiation absorption as an input for charge-carrier models to predict device performance. To examine this assumption, we develop a fully coupled iterative model of charge and radiation transport in semiconductor devices, and we use our model to analyze near-field and far-field GaSb thermophotovoltaic and thermoradiative systems. By comparing our results with past methods that do not consider cross-influences between charge and radiation transport, we find that a fully coupled approach is necessary to accurately model photon recycling and near-field enhancement of external luminescence. As these effects can substantially alter device performance, our modeling approach can aid in the design of efficient thermophotovoltaic and thermoradiative systems.
30 DIRECT ENERGY CONVERSION↗
Numerical analyses of high temperature dense, granular flows coupled to high temperature flow property measurements for solar thermal energy storage
High temperature particle flow properties necessary to predict granular flow behavior for solar thermal energy storage applications were measured and calculated for Carbobead CP 30/60 up to 800 °C. Here, the measured properties included elastic and shear moduli, particle-particle coefficients of static sliding and rolling friction, and particle-particle coefficients of restitution. Poisson’s ratio was calculated with elastic and shear moduli. The flow properties were used as inputs for a numerical model using the discrete element method to examine granular flows along an inclined plane at high temperature. The flow behavior was strongly influenced by the coefficients of static friction, which impacted the particle residence time, shear effects from the side walls, and particle flow mass flux. An 8.7%, 15.6%, and 8.5% increase and 37.9% decrease in steady state mass flow rate was observed for 200 °C, 400 °C, 600 °C, and 800 °C, respectively, when compared to room temperature simulations. A 52%, 59%, and 33% decrease in the time to reach steady state was observed for 200 °C, 400 °C, and 600 °C, respectively, while a 53% increase in time was observed for 800 °C. A significant delay in the flow development at 800 °C was observed due to significantly higher frictional forces.
14 SOLAR ENERGY↗
Spectral Radiative Properties of Ceramic Particles for Concentrated Solar Thermal Energy Storage Applications
This work investigates the spectral radiative properties of ceramic particles using a monochromator and a Fourier-transform infrared spectrometer (FTIR) with integrating spheres at wavelengths from 0.38 μm to 15 μm. Particles are encased between two transparent windows to obtain the directional-hemispherical reflectance of the particle bed. Two types of commercially available particles with three different sizes are examined. Integration over the solar spectrum reveals that the solar absorptance of the particle beds is between 0.940 and 0.957. The total emittance at 1000 K is also estimated by assuming the spectral emittance is independent of temperature. The optical constants of particles are modeled with effective medium approaches, considering the optical properties of individual constituent materials. The absorptance of the particle is estimated using the effective optical constants and compared with that of the particle bed from the measurement. Finally, this work facilitates the characterization of radiative properties of particles with a windowed method and provides a modeling scheme for approximating the radiative properties of composite ceramic materials.
14 SOLAR ENERGY↗
Spectral emittance measurements of micro/nanostructures in energy conversion: a review
Micro/nanostructures play a key role in tuning the radiative properties of materials and have been applied to the high-temperature energy conversion systems for improved performance. Among the various radiative properties, spectral emittance is of integral importance for the design and analysis of materials that function as radiative absorbers or emitters. This article presents an overview of the spectral emittance measurement techniques using both the direct and indirect methods. Several micro/nanostructures are also introduced, and a special emphasis is placed on the emissometers developed for characterizing engineered micro/nanostructures in high-temperature applications (e.g., solar energy conversion and thermophotovoltaic devices). Both experimental facilities and measured results for different materials are summarized. Future prospects in developing instrumentation and micro/nanostructured surfaces for practical applications are also outlined. This study provides a comprehensive source of information for the application of micro/nanostructures in high-temperature energy conversion engineering.
14 SOLAR ENERGY↗
Near-Field Radiative Heat Transfer Between Two α-MoO3 Biaxial Crystals
The near-field radiative heat transfer (NFRHT) between two semi-infinite α-MoO3 biaxial crystals is investigated numerically based on the fluctuation–dissipation theorem combined with the modified 4 × 4 transfer matrix method in this paper. In the calculations, the near-field radiative heat flux (NFRHF) along each of the crystalline directions of α-MoO3 is obtained by controlling the orientation of the biaxial crystals. The results show that much larger heat flux than that between two semi-infinite hexagonal boron nitride can be achieved in the near-field regime, and the maximum heat flux is along the [001] crystalline direction. The mechanisms for the large radiative heat flux are explained as due to existence of hyperbolic phonon polaritons (HPPs) inside α-MoO3 and excitation of hyperbolic surface phonon polaritons (HSPhPs) at the vacuum/α-MoO3 interfaces. The effect of relative rotation between the emitter and the receiver on the heat flux is also investigated. It is found that the heat flux varies significantly with the relative rotation angle. The modulation contrast can be as large as two when the heat flux is along the [010] direction. We attribute the large modulation contrast mainly to the misalignment of HSPhPs and HPPs between the emitter and the receiver. Hence, the results obtained in this work may provide a promising way for manipulating near-field radiative heat transfer between anisotropic materials.
Engineering↗