Engineering topics
Publications and source records attributed to Zhao, Fu.
The study presents a scalable and sustainable extraction method for rare earth, featuring a green, scalable synthesis of diglycolamides that reduces greenhouse gas emissions by 67% and a liquid-liquid extraction workflow.
Aluminum hydroxide, an abundant mineral found in nature, exists in four polymorphs: gibbsite, bayerite, nordstrandite, and doyleite. Among these polymorphs gibbsite, bayerite, and commercially synthesized amorphous aluminum hydroxide have been investigated as sorbent materials for lithium extraction from sulfate solutions. The amorphous form of Al(OH) 3 exhibits a reactivity higher than that of the naturally occurring crystalline polymorphs in terms of extracting Li + ions. This study employed high-temperature oxide melt solution calorimetry to explore the energetics of the sorbent polymorphs. The enthalpic stability order was measured to be gibbsite > bayerite > amorphous Al(OH) 3 . The least stable form, amorphous Al(OH) 3 , undergoes a spontaneous reaction with lithium, resulting in the formation of a stable layered double hydroxide phase. Consequently, amorphous Al(OH) 3 shows promise as a sorbent material for selectively extracting lithium from clay mineral leachate solutions. Further, this research demonstrates the selective direct extraction of Li + ions using amorphous aluminum hydroxide through a liquid–solid lithiation reaction, followed by acid-free delithiation and relithiation processes, achieving an extraction efficiency of 86%, and the maximum capacity was 37.86 mg·g –1 in a single step during lithiation. With high selectivity during lithiation and nearly complete recoverability of the sorbent material during delithiation, this method presents a circular economy model. Furthermore, a life cycle analysis was conducted to illustrate the environmental advantages of replacing the conventional soda ash-based precipitation process with this method, along with a simple operational cost analysis to evaluate reagent and fuel expenses.
With the increasing concern due to climate change caused by a higher atmospheric concentration of CO 2 and other greenhouse gases, reducing environmental impact is becoming more important for every part of society. Manufacturing is responsible for a significant amount of energy/material consumption and environmental burden and, therefore, has a great opportunity to reduce its impact through green manufacturing. Green manufacturing presents opportunities across the manufacturing enterprise to increase the efficient usage of energy and material resources. These opportunities include designing products to consume fewer materials and energy during manufacturing and use, incorporating more efficient manufacturing processes, streamlining and optimizing manufacturing schedules and plans, and circularizing products. The goal of this paper will be to provide a perspective from the authors on the opportunities that exist within green manufacturing for discrete products through a review of pertinent topics and future directions. The paper will focus on processes, manufacturing equipment, manufacturing systems, recovering value at a product’s end-of-life, and additional thoughts that include metrics and indicators, techno-economic assessment, and a discussion of efficiency and effectiveness. Key findings from this review include a need for social indicators and renewable energy considerations in scheduling and process planning, integrating Industry 4.0 into circular economy along with social and institutional dimensions, consistency in the ability to measure and conceptualize metrics and indicators, a detailed evaluation of the life cycle impacts and cost of Addit Manuf, and more human and environment-oriented considerations for smart manufacturing.
Permanent magnets are expected to play a crucial role in the realization of the clean economy. In particular, the neodymium-iron-boron (Nd2Fe14B or NdFeB) magnets, which have the highest energy density among rare earth permanent magnets, are needed for building more efficient windmill generators, electric vehicle motors, etc. Currently, near-net shape magnets can be either made through sintering and compression molding with extensive post machining or directly through injection molding. However, injection molding has a loading volume fraction limitation of 0.65 for nylon binders. A novel method of manufacturing bonded permanent magnets with loading fraction greater than 0.65 has been demonstrated using Big Area Additive Manufacturing (BAAM) printers. As energy density is directly proportional to the square of the magnet loading fraction, magnets produced using BAAM printers require less volume and magnetic material compared to that of injection molded magnets on average. A comparative LCA shows that this difference in magnetic powder consumption nearly constitutes the difference in the environmental impact categories. Even after assuming recycled magnetic input, the BAAM magnets perform better environmentally than injection molded magnets, especially in the ozone depletion category. Since BAAM printers can accommodate even higher loading fractions, at scale, BAAM printers possibly can bring about a significant decrease in rare earth mineral consumption and environmental emissions. So furthermore, single screw extrusion enables BAAM printers to have high print speeds and allow them to be economically competitive against injection molding. Therefore, BAAM printed magnets show promise in transitioning towards the clean economy.
Circularizing end of life products such as electronic waste can open a new source for rare earth elements (REEs) that will decrease the demand pressure on conventional virgin production. The last step to produce REEs consists of a refining process to convert rare earth oxide (REO) to REE metal. One promising technology is processing REO via a room temperature ionic liquid, which is characterized by low energy requirements in contrast to existing REEs extraction processes. In this work, life cycle and techno-economic assessments are performed and compared against molten salt electrolysis. Here, the results show that both processes have advantages and disadvantages in terms of environmental performance, and that they are similarly competitive in terms of economic performance. A breakeven analysis suggests that future research should focus on coupling the production of REOs with the refining processes to attempt to lower REO cost and make them economically feasible in the U.S.
Lithium-ion batteries (LIBs) are expected to play a crucial role in meeting many of the clean energy-related goals. Due to its electrical properties such as good conductance, chemical inertness, and corrosion resistance, graphite is a very popular anode for LIBs. Traditional methods of producing battery-grade graphite (high purity >99%) include processing naturally mined graphite or manufacturing synthetic graphite via the Acheson process, which converts soft amorphous carbons such as petroleum coke into graphite by subjecting it to high temperature (up to 3000 °C) for prolonged periods of times (3–5 days). However, due to a lack of abundant high purity natural graphite sources, synthetic graphite is the preferred choice for many LIBs. A new synthetic electrochemical graphitization method that subjects the amorphous carbon precursor submerged in a molten salt mixture to a constant cathodic polarization (against a graphitic anode) has been discovered that has significantly lower graphitization temperatures (~800 °C) and reduced graphitization time (3–6 h). Furthermore, the method can accept a higher variety of carbon precursors compared to the Acheson process. A prospective life cycle assessment (LCA) is conducted on this new method and compared against the traditional processes. The laboratory-scale demonstration of the method is used to build an inventory, which through various assumptions is scaled up to a commercial scale. An additional scenario is also considered with a biomass-derived carbon precursor for the graphite. The results from the LCA show that while the laboratory scale process is similar to the Acheson process and natural flake graphite in terms of impact, the scaled-up process is drastically better than the Acheson process in all environmental categories. Using a coconut shell-derived biomass precursor has a higher impact due to its manufacturing in Indonesia, as the Indonesian energy grid is highly fossil fuel dependent. Therefore, the biomass carbon may have a higher impact than petroleum coke dependent on the location of production of biomass-derived carbon black. The LCA has identified the molten salt—CaCl 2 —as a potential hotspot and suggests other salts should be considered. Accordingly, the new method shows promise in this early stage LCA in improving the environmental performance of graphite (and by relation LIBs) and therefore needs to be explored more in terms of its commercial viability.
The growing demand of electric vehicles and rapid consumption of rechargeable lithium-ion batteries (LIBs) require recycling of spent cathode active materials (CAMs) to reduce hazardous wastes and supply raw materials to LIB production. To separate CAMs from the cathode, direct calcination of polyvinylidene fluoride (PVDF) binder is widely applied, which leads to high energy consumption and release of toxic hydrogen fluoride. It is desirable to have an environmentally friendly and effective alternative to traditional direct calcination. In this study, five lithium salts, LiOAc (lithium acetate), LiNO 3 , LiCl, Li 2 CO 3 , and Li 2 SO 4 , were deployed and compared for their performance in recycling CAMs. A peel-off efficiency of up to 98.5% was achieved at a LiOAc to LiNO 3 molar ratio of 3:2, salt to cathode mass ratio of 10:1, and temperature of 300 °C at a holding time of 30 min. This system avoids corrosive chemicals and minimizes particle agglomeration of recycled products. Compared with sodium salt systems (NaOAc-NaNO 3 ) or direct calcination, the LiOAc-LiNO 3 system prevented high reaction temperature or further lithium loss and minimized crystal structure and morphological changes. In conclusion, a decomposition mechanism of PVDF through adsorption of HF and fluorine substitution was proposed.
Not provided.
The installed data storage capacity in the U.S. will reach 2.2 Zettabytes by 2025, generating about 50 million units of end-of-life (EOL) hard-disk drives (HDDs) per year. Due to data security concerns, most EOL HDDs are currently shredded (even when still functioning), representing an economic loss. Moreover, raw material extraction linked to the increased demand for storage causes environmental impacts. Besides mitigating the threat posed by sudden restrictions of raw materials, the circular economy (CE) offers to maximize value retention in the economy and reduce the environmental impacts of human activities. Common CE strategies are reusing and recycling products. However, the reuse of hard disk drives is currently burdened by the lack of trust HDD end-users have toward other non-physical means of data removal than shredding. Here, an agent-based modeling (ABM) approach is proposed to explore how techno-economic and social factors affect end-users' decisions to adopt EOL management practices other than shredding. The proposed method also accounts for data uncertainty by applying a semi-quantitative approach. Results demonstrate how increased green procurement and more robust standards could spur end-users' trust toward data-wiping technologies. Even when accounting for uncertainty, HDDs' reuse brings better environmental and economic benefits than HDD shredding followed by material recovery. The semi-quantitative approach proposed in this study could be more universally applied in future ABM, especially given the often-stochastic nature of such models. The developed ABM is also the first to represent several HDD industry stakeholders and demonstrate how the HDD shredding lock-in situation could be resolved.
By 2025, it is estimated that installed data storage in the US will be 2.2 Zettabytes, generating about 50 million units of end-of-life hard-disk drives (HDDs) per year. The circular economy tackles waste issues by maximizing value retention in the economy, for instance, through reuse and recycling. However, the reuse of hard disk drives is hindered by the lack of trust organizations have toward other means of data removal than physically destroying HDDs. Here, an agent-based approach explores how organizations’ decisions to adopt other data removal means affect HDDs circularity. The model applies the theory of planned behaviour to model the decisions of HDDs end-users. Results demonstrate that the attitude (which is affected by trust) of end-users toward data-wiping technologies acts as a barrier to reuse. Moreover, social pressure can play a significant role as organizations that adopt CE behaviours can set an example for others.
By 2025, it is estimated that installed data storage in the U.S. will be 2.2 Zettabytes, generating about 50 million units of end-of-life hard-disk drives (HDDs) per year. The circular economy (CE) tackles waste issues by maximizing value retention in the economy, for instance, through reuse and recycling. However, the reuse of hard disk drives is hindered by the lack of trust organizations have toward other means of data removal than physically destroying HDDs. Here, an agent-based approach explores how organizations' decisions to adopt other data removal means affect HDDs' circularity. The model applies the theory of planned behavior to model the decisions of HDDs end-users. Results demonstrate that the attitude (which is affected by trust) of end-users toward data-wiping technologies acts as a barrier to reuse. Moreover, social pressure can play a significant role as organizations that adopt CE behaviors can set an example for others.
Lithium-ion batteries (LIB) play an essential role in the electrification of the transportation sector, and battery demand for lithium compounds will see a significant increase in the coming decades. This has raised concerns on the supply of lithium, and as a result, technologies are being developed to process unconventional lithium sources. One promising technology is to extract lithium from geothermal brine using lithium-aluminum-layered double hydroxide chloride (LDH) sorbent and forward osmosis. A combined life cycle assessment (LCA) and techno-economic assessment (TEA) is conducted to evaluate the environmental and economic performance of this technology. It is assumed that the lithium extraction unit is an add-on to a 50 MW geothermal power plant located in California. The analysis is based on lab-scale experimental data and stoichiometry while considering the economy of scale for an industrial system. LCA results suggest that, compared with conventional LiOH and Li 2 CO 3 production pathways, the new technology achieves 1–95% reduction in environmental impacts. Even higher reduction can be achieved for LiOH produced via electrolysis. This add-on unit for lithium extraction could achieve a payback period of less than 1 year and reach net present values of $454M and $315M and internal rates of return of 792 and 1130% for LiOH and Li 2 CO 3 production pathways, respectively. The favorable environmental and economic performance suggests that LDH sorption coupled with forward osmosis has great potential to enable the domestic production of battery lithium compounds and that further development should be carried out.