Search NASA⌕ Search

Engineering topics

Zhao, Xianhui

Publications and source records attributed to Zhao, Xianhui.

At least 19 records

Electrospun Nanofibers

Electrospun nanofibers have been considered promising separator candidates for lithium–sulfur (Li–S) batteries due to their unique properties, including but not limited to their high surface area, superior surface-to-volume ratio, excellent flexibility, good mechanical performance, etc. This chapter aims to provide an overview of research in electrospun nanofibers with their applications in Li–S batteries. It starts with a brief introduction to Li–S batteries, followed by the principle and advantages of electrospun nanofibers performed in this area. Applications of electrospun separators in Li–S batteries have been further discussed in detail. In the end, a future vision regarding challenges and perspectives is proposed to provide insightful comments in this field. It is believed that this chapter will provide an extensive and comprehensive reference to utilize this advanced technique to generate novel nanofiber separators for next-generation Li–S batteries.

Zhu, Jiadeng↗

Epoxy Coating of Biofiber: An Effective Modifier of Biofiber Physical and Flow Properties for Improved Tensile Behavior of Biofiber-Reinforced Biocomposite

Biocomposites combine renewable, plant-based fibers with degradable polymers and are an attractive option for sustainable, lightweight, and cost-effective materials with a low carbon footprint, especially for large-scale additive manufacturing. One of the major challenges in the widespread adoption of biocomposites is that their mechanical performance is significantly inferior to that of synthetic composites. Surface treatment is a common and effective technique to improve the mechanical properties of the biofibers used in biocomposites. This study aims to investigate the physical and flow properties of surface-treated biofibers, as well as the tensile properties of their PLA-based biocomposite, to gain insights into how surface treatment changes the fiber‘s characteristics and biocomposite‘s mechanical properties. Surface treatment was created using a two-component epoxy system by reacting poly(bisphenol A-co-epichlorohydrin) glycidyl end-capped (PBG) and dicyandiamide (DICY). The treatment was tested on two different biofibers (loblolly pine and corn stover fibers) with three different PBG/DICY molar ratios (0.25, 0.5, and 2). Results showed that surface-treated fibers improved the tensile strength and Young‘s modulus of the biocomposites. Loblolly pine biocomposites from fibers treated with a PBG/DICY ratio of 0.25 exhibited the best tensile properties. The surface treatment resulted in a more loosely dispersed fiber bulk structure, as evidenced by less fiber agglomeration into smaller particle sizes, higher fiber sphericity, and lower loose bulk density. This can enhance stress distribution and the overall mechanical performance of the biocomposites. Additionally, surface-treated fibers exhibited better dynamic flow properties.

36 MATERIALS SCIENCE↗

Exploring biofiber properties and their influence on biocomposite tensile properties

Biofibers serve as effective reinforcements for neat polylactic acid (PLA) in biocomposites, offering an attractive opportunity to decarbonize the manufacturing sector of the United States by displacing fossil-based reinforcement fibers such as carbon fibers. Also, biofiber production can stimulate economic growth in rural economies, fueling sustainable development. PLA resins are commonly compounded with biofibers to create biocomposites suitable for additive manufacturing. PLA-biofiber composites often exhibit better overall material properties than neat (pure) PLA, but the associations between biofiber properties and the material properties of their biocomposites remain largely unexplored. Hence, this research delves into a comprehensive exploration of diverse biofibers, scrutinizing their physical and chemical attributes, including size, shape, ash content and biochemical composition. The study meticulously analyzes the flow properties of each biofiber and elucidates the ultimate tensile strengths and Young's modulus of corresponding biocomposite samples. Noteworthy correlations between biofiber and biocomposite tensile properties are uncovered, shedding light on critical interrelationships. The study introduces an approach employing regression models to predict the ultimate tensile strength and Young's modulus of biocomposites. These models, validated with a cross-validation technique, exhibit remarkable predictive accuracy, particularly in estimating ultimate tensile strength. © 2024 Oak Ridge National Laboratory managed by UT-Battelle, LLC and The Author(s). Polymer International published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

36 MATERIALS SCIENCE↗

A review of antimicrobial implications for improving indoor air quality

The frequent outbreak of infectious respiratory diseases, such as the recent COVID-19 epidemic, raised the importance of indoor air quality. Removing microorganisms from indoor air is critical to improve indoor air quality. Numerous studies in recent years have been published on developing antimicrobial materials and technologies for antibacterial and antiviral applications. Further, this study critically reviews the recent antimicrobial advances for improving indoor air quality. This paper provides a comprehensive analysis of the antimicrobial mechanisms, development of materials, and deployment strategies, as well as a performance evaluation of the antimicrobial implication for indoor air quality. Furthermore, the challenges and opportunities of future research directions are also highlighted.

59 BASIC BIOLOGICAL SCIENCES↗

Promoting electrochemical rates by concurrent ionic-electronic conductivity enhancement in high mass loading cathode electrode

Enhancing the fast charging capacity of thick electrodes with high mass loading is imperative in expediting the widespread adoption of electric vehicles. Nonetheless, the insufficient charge transfer kinetics of thick electrodes hinder the movement of effective electrons and ions, hence diminishing capacity at high current rates. In this work, we applied sustainable and biodegradable cellulose nanocrystals (CNCs) as electrode additives. It is the first time to simultaneously improve the electronic conductivity by optimizing the carbon dispersion and establishing electron transfer networks, as well as boosting the ionic conductivity of electrodes by shortening the ion transfer pathway. Specifically, the LiNi 0.6 Mn 0.2 Co 0.2 O 2 electrodes incorporating 1% dual functional CNCs additive exhibit improved effective electrical conductivity from 0.11 to 0.16 S/m and risen effective ionic conductivity from 0.36 to 0.62 S/m, in comparison to counterpart electrodes without CNCs. Therefore, the 1% CNC electrode with a high mass loading of 27.0 mg/cm 2 delivers a discharge capacity of 128 mAh/g at 1 C, which is superior to that of the CNC-free electrodes (95 mAh/g). In short, this study presents a novel environmentally friendly, economically viable, and dual-functional electrode additive that enhances both electronic and ionic conductivities with the aim of facilitating the widespread adoption of fast-charging high mass loading electrodes.

25 ENERGY STORAGE↗

Biochar-compost-based controlled-release nitrogen fertilizer intended for an active microbial community

Nitrogen (N) fertilizers in agriculture suffer losses by volatilization of N to the air, surface runoff and leaching into the soil, resulting in low N use efficiency (NUE) (< 50%) and raising severe environmental pollutions. Controlled- release nitrogen fertilizers (CRNFs) can control the release of N nutrients to NUE in crop production. Different methods were used to develop new CRNFs. However, different CRNF technologies are still underdeveloped due to inadequate controlling on N releasing time and/or unsustainable diffusion. The study on the influences of CRNF processing parameters on microbial conditions are lacking when the CRNFs composed of various bio-ingredients such as biochar, composts, and biowaste. The complexity of processing methods, material biodegradability, and other physical properties make current CRNFs of questionable value in agricultural production. This research aims to develop a novel biochar-compost-based controlled-release urea fertilizer (BCRUF) to preserve microbial properties carried by the compost. The BCRUF was synthesized by pelletizing the 50:50 (dry, wt/wt) mixture of biochar and compost. BCRUF was loaded with urea and then spray-coated with polylactic acid (PLA). The releasing time of two types of BCRUFs, coated and uncoated with PLA, for 80% of N release in water was up to 6 h at three different temperatures (4, 23, and 40 °C), compared to conventional urea fertilizer and commercial environmentally smart N (ESN) fertilizer. The releasing time of coated BCRUF for 80% N release in soil was up to 192 h (8 days). Fourier-transform infrared spectroscopy (FTIR) analysis revealed that no new functional groups were found in the release solution, indicating no new chemical hazards generated. The differential scanning calorimetry (DSC) tests also verified that its thermal stability could be up to 160 °C. The microbe populations in the BCRUF pellets were reduced after the pelleting and drying processes in BCRUF fabrication, but a few bacteria can endure in the air-drying process. BCRUF pellets soaked in water for 4 days retained some bacteria. The BCRUF showed very promising characteristics to improve NUE and sustainability in agricultural production.

58 GEOSCIENCES↗

Improving the Recyclability of Polymer Composites With Cellulose Nanofibrils

Cellulose nanofibers (CNFs) have been widely studied for their reinforcing potential in high-performance composites. While there are numerous publications on CNF-reinforced composites in a variety of polymer matrices, few have considered the recyclability of such thermoplastic composites and whether the incorporation of CNFs deteriorates or improves their performance upon reprocessing. In this study, two thermoplastic resins, poly(lactic acid) (PLA), and glycol-modified polyethylene terephthalate (PETg), were prepared with CNF reinforcement and thermomechanically recycled to investigate the effect of CNF inclusion on the composite properties after reprocessing as well as their effect on the composites’ number of useful life cycles. Additionally, changes in mechanical, thermal, rheological, molecular, and microstructural properties of the composites and/or base resins were monitored as a function of cycle numbers. As is typical, the polymers’ molecular weight and mechanical performance deteriorated with continued processing. However, the addition of spray dried CNF was found to better maintain the mechanical performance of both polymers throughout multiple recycling steps as compared to neat samples. For example, the tensile strength of PETg with 20 wt% CNF after 6 processing cycles was found to exceed that of virgin neat PETg, and higher loadings of CNF were found to preserve a higher yield strength during multiple rounds of reprocessing compared to PETg composites with lower CNF loadings. Ultimately this study indicates that the addition of CNF to some thermoplastic materials can increase both their sustainability by offsetting the use of high-embodied energy resins and their circularity by enabling performance retention over more use cycles.

42 ENGINEERING↗

3D printing synthesis of catalysts

The catalyst industry generates approximately $20 billion every year globally and plays a major role in the energy production sector. Traditional industrial catalysts (e.g., pellets) typically have mass and heat transfer limitations, and cause a pressure drop in continuous-flow reactors, lowering the efficiency of the catalytic processes. 3D printing technology has evolved rapidly over the past decade, and the 3D printing of catalysts with desired geometries can address many of the above-stated challenges with traditional catalysts. However, challenges remain to be addressed and opportunities remain to be explored before the full potential in the design and 3D printing of novel catalysts can be realized. Herein this article reviews the recent development in the 3D printing of catalysts. It summarizes the 3D printing design, dimension, property, and performance of 3D printed catalysts. The applications of 3D printed catalysts, such as reforming, wastewater treatment, and CO 2 capture and removal, are discussed, with a techno-economic analysis and life cycle analysis. Future research directions and opportunities for 3D printing of catalysts are also highlighted.

25 ENERGY STORAGE↗

Insights into activators on biomass-derived carbon-based composites for electrochemical energy storage

Biomass-derived carbon materials are now an essential source of carbon electrodes for high-performance supercapacitors due to their cost-effectiveness and abundant heteroatom self-doping properties. When preparing porous carbon materials from biomass for supercapacitor use, the use of activators can significantly increase the specific surface area of carbon materials, enhance pore structures, introduce more heteroatoms, promote the generation of various functional groups, and play a crucial role in the capacitance performance of biomass-derived carbon materials. However, the role of activators during the activation process has been overlooked in previous work focused on improving supercapacitor capacitance performance. In addition, there is a lack of comprehensive reviews summarizing the role of activators. Therefore, this work classifies the types of activators, discusses their activation mechanisms, operability, economy, and environmental friendliness, and proposes future development directions for activators. The main mixing methods of activators and carbon materials are also demonstrated, highlighting the advantages and disadvantages of each method. In conclusion, this work could provide valuable insights for the development of activators for high-performance supercapacitors.

25 ENERGY STORAGE↗

Biomass-derived carbon dots as emerging visual platforms for fluorescent sensing

Biomass-derived carbon dots (CDs) are non-toxic and fluorescently stable, making them suitable for extensive application in fluorescence sensing. The use of cheap and renewable materials not only improves the utilization rate of waste resources, but it is also drawing increasing attention to and interest in the production of biomass-derived CDs. Visual fluorescence detection based on CDs is the focus of current research. This method offers high sensitivity and accuracy and can be used for rapid and accurate determination under complex conditions. Here, this paper describes the biomass precursors of CDs, including plants, animal remains and microorganisms. The factors affecting the use of CDs as fluorescent probes are also discussed, and a brief overview of enhancements made to the preparation process of CDs is provided. In addition, the application prospects and challenges related to biomass-derived CDs are demonstrated.

54 ENVIRONMENTAL SCIENCES↗

Structure-property relationship between lignin structures and properties of 3D-printed lignin composites

Lignin is a low-cost and renewable bioresource with a huge annual production promising to prepare sustainable materials. However, the poor interfacial adhesion between many lignin-polymer pairs deteriorates the mechanical performance of the composites, which seriously limits the application of lignin in 3D printing via fused depositional modeling. This work examined lignin-polyamide 12 (PA 12) intermolecular interactions (e.g., hydrogen bonding) to address the interface challenge. To realize this goal, the phenolic hydroxyl content was increased for a kraft softwood lignin using a LiBr/HBr demethylation procedure, increasing phenoxy content by 61.7%. Increased hydrogen bonding interactions between modified lignin (Pine-Lig-OH) and PA 12 demonstrated a significantly improved molten dynamic modulus by rheological analysis. Regarding mechanical properties, by adding 20 wt% of Pine-Lig-OH, the tensile strength and Young's modulus reached 46.6 MPa and 1.62 GPa, 30.2% and 33.9% higher than PA 12, respectively. Further morphological analysis proved the interfacial interactions are enhanced by showing the difference in the phase gaps. The dynamic mechanical analysis (DMA) supported the conclusion that Pine-Lig-OH could interact with polymer chains, alternating segmental movements due to the strong interaction. Here, this study presents a method to enhance lignin composite properties by promoting interactions with the polymer matrix through modified functional groups, guiding future lignin composite research.

36 MATERIALS SCIENCE↗

Nondestructively Visualizing and Understanding the Mechano-Electro-chemical Origins of “Soft Short” and “Creeping” in All-Solid-State Batteries

All-solid-state Li-metal batteries (ASLMBs) represent a significant breakthrough in the quest to overcome limitations associated with traditional Li-ion batteries, particularly in energy density and safety aspects. However, widespread implementation is stymied due to a lack of profound understanding of the complex mechano-electro-chemical behavior of Li metal in the ASLMBs. Herein, operando neutron imaging and X-ray computed tomography (XCT) are leveraged to nondestructively visualize Li behaviors within ASLMBs. This approach offers real-time observations of Li evolutions, both pre- and post- occurrence of a “soft short”. The coordination of 2D neutron radiography and 3D neutron tomography enables charting of the terrain of Li metal deformation operando. Concurrently, XCT offers a 3D insight into the internal structure of the battery following a “soft short”. Despite the manifestation of a “soft short”, the persistence of Faradaic processes is observed. To study the elusive “soft short”, phase field modeling is coupled with electrochemistry and solid mechanics theory. The research unravels how external pressure curbs dendrite growth, potentially leading to dendrite fractures and thus uncovering the origins of both “soft” and “hard” shorts in ASLMBs. Furthermore, by harnessing finite element modeling, it dive deeper into the mechanical deformation and the fluidity of Li metal.

25 ENERGY STORAGE↗

Life cycle cost, energy, and carbon emissions of molds for precast concrete: Exploring the impacts of material choices and additive manufacturing

Molds for precast concrete are commonly used to create simple- to complex-shaped concrete products away from construction sites. These molds are often handmade from wood; however, additively manufacturing (AM, or 3D printing) fiber-reinforced polymer composites is an advantageous alternative, producing significantly more durable, highly complex molds faster, but likely at a higher cost. Here, this study explores the impact of material and production variables on the cost, energy, and carbon emissions of employing composite AM molds over the full lifecycle. The case study employed techno-economic and life cycle assessments to show that using wood flour–poly(lactic acid) or recycled carbon fiber–acrylonitrile butadiene styrene for AM molds can be less expensive than conventional wood molds, especially when considering use phase costs. While wood molds have the least environmental impacts due to wood's higher biogenic carbon sequestration and minimal processing, optimizing AM designs could reduce energy demand, carbon emissions, and cost.

36 MATERIALS SCIENCE↗

Bioinspired design toward nanocellulose-based materials

Nature provides lots of inspiration for material and structural design for various applications. Deriving design principles from the investigation of nature can provide a rich source of inspiration for the development of multifunctional materials. The bioinspired design templates mainly include mussels, nacre, and various plant species. As a sustainable and renewable feedstock, nanocellulose can be used to fabricate advanced materials with multifunctional properties through bioinspired designs. However, challenges and opportunities remain for realizing the full potential in the design of novel materials. Here, this article reviewed recent development in the bioinspired nanocellulose based materials and their application. This article summarizes the functions (e.g., surface wetting) and applications (e.g., composite) of bioinspired nanocellulose-based materials. The bioinspired design templates are discussed along with strategies, advantages, and challenges to the development of synthetic mimics. Additionally, mechanisms and processes (e.g., chemical modification, self-assembly) leading to biomimetic design are discussed. Finally, future research directions and opportunities of bioinspired nanocellulose-based materials are highlighted.

36 MATERIALS SCIENCE↗

Towards the applications of mechanophore incorporated feedstocks for additive manufacturing

The ability to additively-manufacture mechanically responsive molecules, known as mechanophores (MPs), that are incorporated into polymer feedstocks provides opportunities for self-healing, real-time damage detection, and improvements in quality assurance and control capabilities to several industries (wind energy technology, building and construction, etc.) who are adopting additive manufacturing (AM). However, before the applications are realized and industrially adopted, further research and development regarding MP-incorporated AM feedstock availability, production scale-up, and processability and printability is needed. Here, the goal of this review is to bridge the gap between the bench top and real world applications of AM of MPs by identifying high impact application spaces and highlighting the challenges that need to be overcome for widespread adoption. The state-of-the-art of AM of MP-incorporated feedstocks is reviewed, followed by a discussion of potential future applications, current challenges, and research areas that work toward commercialization of AM of MP-incorporated feedstocks.

36 MATERIALS SCIENCE↗

Active metal catalyst

A method of forming a catalyst is provided herein. The method comprises combining a binder, a support, and an active metal to form a slurry composition. The method further comprises applying the slurry composition using an additive manufacturing process to form a green part. The method further comprises exposing the green part to heat at a temperature of from about 10° C. to about 150° C. to form the hardened part. The method further comprises applying a ceramic-based coating material to the hardened part to form the catalyst.

Zhao, Xianhui↗