Search NASA⌕ Search

Engineering topics

Zhao, Xianhui [ORNL] (ORCID:0000000202825810)

Publications and source records attributed to Zhao, Xianhui [ORNL] (ORCID:0000000202825810).

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

A synergistic approach to improve the cellulose nanofibril dispersion in poly(lactic acid) composites as feedstocks for extrusion-based additive manufacturing

Hybrid fiber-reinforced polymer composites (HFRPs) are multifunctional materials that bear more than one characteristic benefit. In this study, hybrid cellulose fibers, e.g., pulp fiber (PF) and cellulose nanofibril (CNF), were used for reinforcing poly(lactic acid) (PLA). A synergistic approach was applied to disperse CNF. The low-surface-tension solvent (ethanol), together with PF templating, assisted the dispersion of CNF in PLA. The HFRP achieved a higher tensile strength (∼70 MPa, 29% increase from PLA) and modulus (∼7 GPa, 46% increase from PLA), as well as a higher heat deflection temperature (∼60℃, 6℃ increase compared to neat PLA), compared to single-reinforcement FRPs. Additionally, the formulation was demonstrated to be potentially suitable for large-scale additive manufacturing.

Bista, Bivek [University of Maine]↗
DOE OSTI2026

Thermokinetic mixing compounding for polymer composites – a comprehensive review

High-speed thermokinetic mixers (K-mixers) represent an advanced compounding technology that employs intense shear and friction to convert kinetic energy directly into thermal energy. This mechanism enables rapid mixing cycles, often under one minute, facilitating exceptional filler dispersion while minimizing the material’s thermal history. This is particularly effective for compounding challenging materials, including heat-sensitive biopolymers, wet filler feedstocks, and nanofillers prone to agglomeration. As the first comprehensive review of this technology, this article synthesizes the fundamental principles of thermokinetic mixing (K-mixing) and surveys recent advances in polymer composite fabrication. We contrast the working principles of K-mixers with conventional twin-screw extrusion, highlighting distinct advantages in dispersing nanoscale fillers, exfoliating layered materials, and processing wet cellulosic feedstocks and ultra-high filler loadings (e.g., 85 wt%). Furthermore, strategies to optimize filler–matrix interfacial bonding under rapid-processing constraints, such as the kinetic selection of compatibilizers and fiber surface treatments, are evaluated. Finally, we analyze key structure-processing-property relationships and outline future directions in scaling up, reactive processing, and hybrid material development.

Zhang, Xuefeng [University of Maine]↗
DOE OSTI2026

Controlled lithium stripping enables a stable interface for long-cycling anode-free solid-state batteries

Anode-free solid-state batteries (AFSSBs) are a promising route toward achieving high energy density. In these cells, the anode contains no pre-stored lithium (Li). Instead, the entire Li inventory originates from the cathode and is freshly deposited onto a bare current collector during charging. However, achieving uniform and defect-free Li plating on this bare current collector remains a major challenge, often resulting in low Li plating/stripping efficiency and rapid capacity decay. Here, for the first time, operando neutron imaging is employed to visualize Li plating/stripping behavior in an anode-free full cell with LiNi0.82Mn0.07Co0.11O2 (NMC) as the cathode. Operando measurements reveal that complete stripping of Li leaves isolated Li residues on the current collector, which degrades the interfacial contact between the current collector and the solid-state electrolyte. To mitigate this interfacial issue and promote more uniform Li deposition, we implement a discharge-cutoff-voltage strategy that intentionally retains a thin residual Li layer after stripping. This preserved Li-containing interfacial reservoir not only improves interfacial contact but also serves as an in situ formed seed layer that enables more homogeneous subsequent Li plating. As a result, the optimized anode-free cell with limited stripping depth exhibits excellent long-term cycling stability, maintaining a discharge capacity of 112.1 mAh g−1 with a capacity retention of 80.6% and an average coulombic efficiency of approximately 99.9% after 500 cycles at 0.25 C. In contrast, the cell with a conventional discharge cutoff voltage of 2.8 V exhibits rapid capacity decay, retaining only 59.7 mAh g−1 after 50 cycles with a capacity retention of 40.7%. This work demonstrates that limiting deep stripping to preserve a thin Li-containing interfacial layer can effectively improve the cycling stability of sulfide-based AFSSBs.

Wang, Jiwei [Northeastern University, Boston]↗
DOE OSTI2026

Biochar–polymer composites for 3D printing: a review

Biochar, a bio-based co-product of biofuel production via thermochemical conversion, holds potential as a filler for polymer composites to reduce costs, improve thermomechanical properties, and aid in environmental remediation. 3D-printed biochar composites have received growing interest over the past few years but have experienced difficulties such as poor layer adhesion and nozzle clogging. Currently, no literature review examines 3D-printed biochar composites and related biochar properties in-depth. This work summarizes and discusses recent studies on 3D-printed polymer and biochar composites and examines their mechanical, thermal, and additional properties that result from each study. Technical challenges in printability, such as nozzle clogging from particle size and biochar aggregation, are also discussed. Furthermore, this work discusses the variability of biochar properties resulting from the pyrolysis conditions and feedstock choice in relation to potential 3D printing outcomes. In particular, several studies reported that high lignin feedstocks could be candidates for 3D printing. The post-processing approaches of the biochar via physical and chemical methods are also introduced. Ball milling appears to hold the most promise for physical treatments due to its tunability of particle size, surface area, and functional groups, while chemical treatments with acids or alkalis are used to tailor biochar porosity and wettability. Overall, it was determined that future research needs to be done relating biochar production and post-processing methods to resulting 3D printing parameters as the number of studies is limited.

Day, Rachel [Auburn University, Auburn, AL]↗