Search NASA⌕ Search

Engineering topics

Zheng, Dong

Publications and source records attributed to Zheng, Dong.

At least 19 records

In-situ electrochemical optical techniques in the investigation of lithium interfacial phenomena with a liquid and a solid-state electrolyte

An in-situ electrochemical optical diagnosis is the key to the investigation of electrode interface during a redox reaction. Because the morphology changes particularly, dendrite formation, dendrite shapes, solid electrolyte interface formation and gas generation can be revealed visually. The challenge of ensuring uniform current density on a flat Li anode in a liquid electrolyte was addressed and uniform Li plating was demonstrated. The dendrite shape change under different reduction current density was discussed. Here the Li dendrite shape change and the performance of Li anodes with a surface lamination of graphite and red phosphate were used as examples to demonstrate the capability of the in-situ optical cell. An in-situ electrochemical optical cell used in the investigation of the increasingly popular solid-state Li batteries has its own challenges. Due to the untransparent nature of a solid-state electrolyte, an optical investigation on a solid-state electrolyte Li battery needs to be done by exposing the cross-section of the cell. In addition, it is very difficult to assemble an optical cell with a brittle and fragile solid-state electrolyte in a glove box. A set of formation and transfer dies, and an optical cell were introduced. The Li dendrite growth at the interface can be observed in a solid-state Li cell.

25 ENERGY STORAGE↗

High-performance all-solid-state Li–S batteries enabled by an all-electrochem-active prelithiated Si anode

The development of all-solid-state Li–S batteries has been greatly impeded by dendrite growth and dendrite penetration, which are both related to the Li metal anode. As a compromised alternative, we report lithium silicide (Li x Si) as a dendrite-free and high-capacity anode with Li source. Here, the as-synthesized Li x Si is relatively soft, highly electronically conductive, and with a high Li diffusivity. These distinctive properties make Li x Si anode viable as an “all-electrochem-active” electrode (consisted of 100 wt.% Li x Si). Compared with the typical composite electrode, the all-electrochem-active electrode not merely maximizes the electrode-level energy density but also minimizes the electrolyte-related interfacial degradation. Li x Si symmetric cell demonstrates a reversible cycling at 4 mA cm –2 for over 320 h. Stress change and morphological evolution of the Li x Si electrode are investigated upon dealloying/alloying. When paired with a S cathode (active mass loading of 3 mg cm –2 ), Li x Si–S full cell shows a good cycling behavior over 500 cycles and rate performance (69% capacity retained at 1.2C) even at 25 °C.

25 ENERGY STORAGE↗

Practically Accessible All-Solid-State Batteries Enabled by Organosulfide Cathodes and Sulfide Electrolytes

The combination of organic electrode materials and sulfide electrolytes is expected to enable the development of all-solid-state organic batteries featuring high energy density and long-term sustainability. In this work, thiuram hexasulfide is reported as a low-cost and high-capacity organic cathode for solid-state batteries based on sulfide electrolytes, delivering a capacity of ~600 mAh g -1 and retaining 80.8 % capacity after 500 cycles. An electrochemically reversible change of the cathode interface was revealed upon cycling. Full cell displays an oscillating stress change up to 0.6 MPa during cycling, predominated by the anode side. The energy density is 1140 Wh kg -1 at the material level and 376 Wh kg -1 at the electrode level, which are among the best-reported organic cathodes to date. A high areal capacity of 10.4 mAh cm -2 is reached with a high mass loading cathode. A dry-film approach is further explored to manufacture sheet-type cells. Free-standing electrolyte film is merely ~48 μm thick and demonstrates an ultralow areal resistance of 3.9 Ω cm 2 , significantly boosts the cell-level energy density and reduces the cell internal resistance.

25 ENERGY STORAGE↗

A high-performance organic cathode customized for sulfide-based all-solid-state batteries

All-solid-state batteries (ASSBs) have become increasingly attractive recently due to their better safety and prospective long-term stability compared with conventional liquid batteries. However, obtaining a sustainable cathode candidate to match the solid electrolyte with regards to operating potential, chemical compatibility, and mechanical property is still an open challenge. In this work, the chemical incompatibility of quinone-based active materials and sulfide-based electrolyte were unveiled for the first time through a heteroconjugate addition reaction mechanism. To develop a quinone cathode customized for sulfide-based ASSBs, poly-(anthraquinonyl sulfide)-graphene (PAQS-G) nanocomposite was reported. The stable polymer framework of PAQS can protect the quinone redox center by preventing nucleophilic attack from sulfide-based solid electrolytes. The graphene additives can ameliorate redox kinetics and improve active material utilization. The PAQS-G cathode exhibited a specific capacity of ~178 mAh g -1 and a high material utilization of ~79%. Excellent cycling stability was achieved with 94 % capacity after 200 cycles in lithium batteries and 95.5 % capacity after 300 cycles in sodium batteries at 0.1C rate, respectively. A promising potential for energy storage applications was demonstrated.

25 ENERGY STORAGE↗

A redox-active organic cation for safer metallic lithium-based batteries

Safety concerns have severely impeded the practical application of high-energy-density lithium-based batteries. Dendrite growth and overcharging can lead to particularly catastrophic thermal failure. Here we report an organic cation, trisaminocyclopropenium (TAC), as a bi-functional electrolyte additive to suppress dendrite growth and offer reversible overcharge protection for metallic lithium-based batteries. During the Li plating process, TAC cations with aliphatic chains can form a positively charged electrostatic shield around Li protrusions, repelling the approaching Li + and thereby attaining a more uniform plating. A two times longer cycle life of 300 h at 1 mA cm -2 is achieved in a Li|Li symmetric cell in comparison with the control. During the overcharging process, the redox-active TAC can repeatedly shuttle between two electrodes, maintaining the cell voltage within a safe value. A solid protection of 117 cycles (~1640 h) at 0.2 C with a 100% overcharge is achieved in a LiFePO 4 /Li 4 Ti 5 O 12 cell. This study sheds fresh light on the ability of organic cations to build safer batteries.

25 ENERGY STORAGE↗

A redox-active organic cation for safer high energy density Li-ion batteries

Ni-rich layered cathode materials are at the forefront to be deployed in high energy density Li-ion batteries for the automotive market. However, the intrinsic poor structural and interfacial stability during overcharging could trigger violent thermal failure, which severely limits their wide application. To protect the Ni-rich cathode from overcharging, we firstly report a redox-active cation, thioether-substituted diaminocyclopropenium, as an electrolyte additive to limit the cell voltage within the safe value during overcharging. The organic cation demonstrates a record-breaking electrochemical reversibility at ~4.55 V versus Li + /Li and solubility (0.5 M) in carbonate-based electrolyte. The protection capability of the additive was explored in two cell chemistries: a LiNi 0.8 Co 0.15 Al 0.05 O 2 /graphite cell and a LiNi 0.8 Co 0.15 Al 0.05 O 2 /silicon–graphene cell with areal capacities of ~2.2 mA h cm -2 and ~3 mA h cm -2 , respectively. With 0.2 M addition, the LiNi 0.8 Co 0.15 Al 0.05 O 2 /graphite cell survived 54 cycles at 0.2C with 100% overcharge. Moreover, the cell can carry an utmost 4.4 mA cm -2 (2C) with 100% overcharge and a maximum capacity of 7540% SOC at 0.2C.

25 ENERGY STORAGE↗

High performance lithium-ion and lithium–sulfur batteries using prelithiated phosphorus/carbon composite anode

Controlled chemical prelithiation of high capacity phosphorous/carbon (P/C) composite anode has been applied to develop advanced lithium-ion batteries (LIBs). The initial coulombic efficiency (CE) of P/C is significantly improved (up to 93% for fully-prelithiated P/C) owing to the formation of an artificial solid electrolyte interface (SEI) layer, which is characterized by SEM, Raman and XPS analyses. It ensures the application of P/C anode in real battery assembly. A partly-prelithiated P/C anode prepared by 20 sec prelithiation treatment is paired with a LiCoO2 (LCO) cathode. Here, the full cell delivers a highly reversible capacity of ~ 104 mAh g -1 LCO at 1C rate and retains a CE close to 100% over 2000 cycles. Moreover, a fully-prelithiated P/C anode prepared by 10 min prelithiation treatment is paired with a high-capacity Lifree sulfur/carbon (S/C) cathode. This newly configured full cell delivers a good rate and cycling performance and a high energy density of 358 Wh kg -1 .

25 ENERGY STORAGE↗

The Progress of Li-S Batteries-Understanding of the Sulfur Redox Mechanism: Dissolved Polysulfide Ions in the Electrolytes

Rechargeable lithium–sulfur batteries have aroused great attention in recent years. Thousands of research articles are published, and among these publications, the majority are dedicated to improving the battery's performance through chemically and physically modifying the sulfur electrode, electrolytes, separator, and lithium anode. However, the single most important aspect, understanding the sulfur redox mechanism, is sparse and overwhelmed by the huge volume of work done on improving the battery's performance. Besides the intrinsic complexity of the sulfur redox chemistry, the most challenging task is to find an effective analytical technique for the quantitative and qualitative determination of the dissolved and solid polysulfides, including elemental sulfur. In this paper, the recent important research aiming to understand the redox mechanism of the sulfur electrode is reviewed in light of the unique analytical techniques used in the research. The review re–affirms the complexity of the sulfur redox chemistry and lays the background for the future mechanistic research for Li–S batteries.

25 ENERGY STORAGE↗

Systematic and rapid screening for the redox shuttle inhibitors in lithium-sulfur batteries

High performance liquid chromatography (HPLC) can be used to systematically and rapidly screen the potential additives for the inhibition of the polysulfide shuttle effect in a Li-S battery. The method is proven effective by investigating the 18 compounds which were reported in the literature as redox shuttle inhibitors for Li-S batteries. The change of the polysulfide ions from being exposed to 18 different redox shuttle inhibition additives was qualitatively and quantitatively determined. The changes of polysulfide species and elemental sulfur were successfully used to study the inhibition effect of the additives in Li-S batteries. It was confirmed that nitrate salts under the same concentration showed the best inhibition effect for the polysulfide shuttle reaction. However even in the electrolyte with nitrate additives, the shuttle reactions between Li metal and polysulfides (and elemental sulfur) are still notable, and thus the search for a better polysulfide shuttle inhibitor is ongoing and critical for improving the electrochemical performance of Li-S batteries.

25 ENERGY STORAGE↗

Sulfur redox reactions on nanostructured highly oriented pyrolytic graphite (HOPG) electrodes: Direct evidence for superior electrocatalytic performance on defect sites

Fundamental research of sulfur redox reactions on well-defined controlled model electrode surfaces can provide new information to design high-performance lithium-sulfur batteries. In this paper, we study the electrochemical reduction and oxidation of sulfur on the nanostructured HOPG electrodes with pure basal planes, step plans, and pure edge planes. Finally, our results directly indicate that electrochemical reduction and oxidation of sulfur is significantly affected by the carbon surface structure, namely, the electrochemical reversibility of sulfur redox reaction is much better on edge plane, compared with basal plane and step plane.

36 MATERIALS SCIENCE↗