Search NASA⌕ Search

Engineering topics

Zhernenkov, Mikhail

Publications and source records attributed to Zhernenkov, Mikhail.

At least 37 records · Page 2

Mesocrystalline Ordering and Phase Transformation of Iron Oxide Biominerals in the Ultrahard Teeth of Cryptochiton stelleri

Biological organisms naturally synthesize complex, hierarchical, multifunctional materials through mineralization processes at ambient conditions and under physiological pH. One such example is the ultrahard and wear-resistant radular teeth found in mollusks, which are used to scape against the rock to feed on algae. Herein, the biologically controlled structural development of the hard, outer magnetite-containing shell of the chitin teeth is revealed. Specifically, the formation of a series of mesocrystalline iron oxide phases, templated by chitin-binding proteins, is identified. The initial domains, consisting of ferrihydrite mesocrystals with a spherulite-like morphology, undergo a solid-state phase transformation to form magnetite while maintaining mesocrystallinity, likely via a shear-induced solid-state reaction, without any noticeable architectural changes. Subsequent growth via Ostwald ripening leads to nearly single-crystalline rod-like elements. In addition, an interpenetrating organic matrix is identified that, at early stages of tooth development, potentially contains iron-binding proteins that guide the self-assembly of the mesocrystalline mineral and influence the preferred orientation of the later-formed magnetite nanorods, which ultimately determines the mechanical behavior of the mature chiton teeth.

36 MATERIALS SCIENCE↗

Self-Assembly of Flexible Linear–Semiflexible Bottlebrush–Flexible Linear Triblock Copolymers

Block copolymer (BCP) self-assembly is a fundamental process in which incompatible blocks spontaneously form organized microstructures with broad practical applications. Classical understanding is that the domain spacing is limited by the contour length of the polymer backbone. Here, using a combination of molecular design, chemical synthesis, small-/wide-angle X-ray scattering, transmission electron microscopy, and electron tomography, we discover that this molecular picture does not hold for architecturally semiflexible BCPs. For strongly segregated linear–semiflexible bottlebrush–linear triblock copolymers, the size of the bottlebrush domain can be twice the bottlebrush backbone contour length. The mechanism of such anomalous self-assembly is likely that the interfacial repulsion between the incompatible blocks is large enough to pull a part of the linear end blocks into the bottlebrush domain. This effectively increases the bottlebrush domain size. Moreover, the semiflexible bottlebrush widens the regime for the cylinder morphology that is associated with the volume fraction of the end blocks fC SFB ∈ (0.10, >0.41). This window is much wider than that for flexible linear BCPs, fC F ∈ (0.14, 0.35), and that predicted by the recent self-consistent field theory for linear-bottlebrush BCPs of the same chemistry and molecular architecture. Finally, our experimental findings reveal previously unrecognized mechanisms for the self-assembly of architecturally complex BCPs.

36 MATERIALS SCIENCE↗

Dynamic processes in transient phases during self-assembly of organic semiconductor thin films

Understanding and manipulating crystallization processes has been an important challenge for solution-processed organic thin films, both for fundamental studies and for fabricating thin films with near-intrinsic charge transport properties. We report an in situ X-ray scattering study of the crystallization of 2-decyl-7-phenyl-[1]benzothieno[3,2-b][1]benzothiophene (Ph-BTBT-C 10 ) during its deposition from solution. At temperatures modestly below the smectic-E/crystalline phase boundary, the crystallization goes through a transient liquid crystal state before reaching the final stable crystalline phase. Significant dynamics occur in the first few seconds of the transition, which are observed through fluctuations in the X-ray scattering intensity, and are correlated with the time interval that the transient thin film coexists with the evaporating solvent. The transition to the stable crystalline phase takes minutes or even hours under these conditions, which may be a result of the asymmetry of the molecule. Transient phases are of potential interest for applications, since they can act as a route to self-assembly of organic thin films. However, our observations show that the long-lived monolayer-stacked intermediate state does not act as a template for the bilayer-stacked crystalline phase. Rather, the grain structure is replaced through nucleation, where the nucleation free-energy barrier is related to a potential barrier that prevents molecules to flip their long axis by 180°.

36 MATERIALS SCIENCE↗

Structure Development of the Interphase between Drying Cellulose Materials Revealed by In Situ Grazing-Incidence Small-Angle X-ray Scattering

The nano- to microscale structures at the interface between materials can define the macroscopic material properties. These structures are extremely difficult to investigate for complex material systems, such as cellulose-rich materials. The development of new model cellulose materials and measuring techniques has opened new possibilities to resolve this problem. We present a straightforward approach combining micro-focusing grazing-incidence small-angle X-ray scattering and atomic force microscopy (AFM) to investigate the structural rearrangements of cellulose/cellulose interfaces in situ during drying. Based on the results, we propose that molecular interdiffusion and structural rearrangement play a major role in the development of the properties of the cellulose/cellulose interphase; this model is representative of the development of the properties of joint/contact points between macroscopic cellulose fibers.

36 MATERIALS SCIENCE↗

Glasses denser than the supercooled liquid

When aged below the glass transition temperature, T g , the density of a glass cannot exceed that of the metastable supercooled liquid (SCL) state, unless crystals are nucleated. The only exception is when another polyamorphic SCL state exists, with a density higher than that of the ordinary SCL. Experimentally, such polyamorphic states and their corresponding liquid–liquid phase transitions have only been observed in network-forming systems or those with polymorphic crystalline states. In otherwise simple liquids, such phase transitions have not been observed, either in aged or vapor-deposited stable glasses, even near the Kauzmann temperature. Here, we report that the density of thin vapor-deposited films of N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine (TPD) can exceed their corresponding SCL density by as much as 3.5% and can even exceed the crystal density under certain deposition conditions. We identify a previously unidentified high-density supercooled liquid (HD-SCL) phase with a liquid–liquid phase transition temperature (T LL ) ~35 K below the nominal glass transition temperature of the ordinary SCL. Additionally, the HD-SCL state is observed in glasses deposited in the thickness range of 25 to 55 nm, where thin films of the ordinary SCL have exceptionally enhanced surface mobility with large mobility gradients. The enhanced mobility enables vapor-deposited thin films to overcome kinetic barriers for relaxation and access the HD-SCL state. The HD-SCL state is only thermodynamically favored in thin films and transforms rapidly to the ordinary SCL when the vapor deposition is continued to form films with thicknesses more than 60 nm.

36 MATERIALS SCIENCE↗

Gaussian processes for autonomous data acquisition at large-scale synchrotron and neutron facilities

The execution and analysis of complex experiments are challenged by the vast dimensionality of the underlying parameter spaces. Although an increase in data-acquisition rates should allow broader querying of the parameter space, the complexity of experiments and the subtle dependence of the model function on input parameters remains daunting owing to the sheer number of variables. New strategies for autonomous data acquisition are being developed, with one promising direction being the use of Gaussian process regression (GPR). GPR is a quick, non-parametric and robust approximation and uncertainty quantification method that can be applied directly to autonomous data acquisition. We review GPR-driven autonomous experimentation and illustrate its functionality using real-world examples from large experimental facilities in the USA and France. We introduce the basics of a GPR-driven autonomous loop with a focus on Gaussian processes, and then shift the focus to the infrastructure that needs to be built around GPR to create a closed loop. Finally, the case studies we discuss show that Gaussian-process-based autonomous data acquisition is a widely applicable method that can facilitate the optimal use of instruments and facilities by enabling the efficient acquisition of high-value datasets.

36 MATERIALS SCIENCE↗

Patternable Mesoporous Thin Film Quantum Materials via Block Copolymer Self-Assembly: An Emergent Technology?

Recent developments in quantum materials hold promise for revolutionizing energy and information technologies. The use of soft matter self-assembly, for example, by employing block copolymers (BCPs) as structure directing or templating agents, offers facile pathways toward quantum metamaterials with highly tunable mesostructures via scalable solution processing. Here, we report the preparation of patternable mesoporous niobium carbonitride-type thin film superconductors through spin-coating of a hybrid solution containing an amphiphilic BCP swollen by niobia sol precursors and subsequent thermal processing in combination with photolithography. Spin-coated as-made BCP-niobia hybrid thin films on silicon substrates after optional photolithographic definition are heated in air to produce a porous oxide, and subsequently converted in a multistep process to carbonitrides via treatment with high temperatures in reactive gases including ammonia. Grazing incidence small-angle X-ray scattering suggests the presence of ordered mesostructures in as-made BCP-niobia films without further annealing, consistent with a distorted alternating gyroid morphology that is retained upon thermal treatments. Wide-angle X-ray scattering confirms the synthesis of phase-pure niobium carbonitride nanocrystals with rock-salt lattices within the mesoscale networks. Electrical transport measurements of unpatterned thin films show initial exponential rise in resistivity characteristic of thermal activation in granular systems down to 12.8 K, at which point resistivity drops to zero into a superconducting state. Magnetoresistance measurements determine the superconducting upper critical field to be over 16 T, demonstrating material quality on par with niobium carbonitrides obtained from traditional solid-state synthesis methods. Here. we discuss how such cost-effective and scalable solution-based quantum materials fabrication approaches may be integrated into existing microelectronics processing, promising the emergence of a technology with tremendous academic and industrial potential by combining the capabilities of soft matter self-assembly with quantum materials.

36 MATERIALS SCIENCE↗

Synchrotron Microbeam Diffraction Studies on the Alignment within 3D-Printed Smectic-A Liquid Crystal Elastomer Filaments during Extrusion

3D printing of novel and smart materials has received considerable attention due to its applications within biological and medical fields, mostly as they can be used to print complex architectures and particular designs. However, the internal structure during 3D printing can be problematic to resolve. We present here how time-resolved synchrotron microbeam Small-Angle X-ray Diffraction (μ-SAXD) allows us to elucidate the local orientational structure of a liquid crystal elastomer-based printed scaffold. Most reported 3D-printed liquid crystal elastomers are mainly nematic; here, we present a Smectic-A 3D-printed liquid crystal elastomer that has previously been reported to promote cell proliferation and alignment. The data obtained on the 3D-printed filaments will provide insights into the internal structure of the liquid crystal elastomer for the future fabrication of liquid crystal elastomers as responsive and anisotropic 3D cell scaffolds.

36 MATERIALS SCIENCE↗

Anisotropic Resonant X-ray Diffraction of a Conjugated Polymer at the Sulfur K-Edge

The planar, aromatic nature of the backbone of conjugated polymers endows them with anisotropic properties. Here we show that the resonant X-ray diffraction of a sulfur-containing semicrystalline conjugated polymer at the sulfur K-edge is highly anisotropic, with strong modulation of diffracted intensity depending upon the relative orientation of the polarization of the incident beam with respect to the diffracting crystal planes. Through determination of the anisotropic resonant scattering factors, we can spectroscopically reproduce the observed resonant anisotropic scattering effects based on a proposed unit cell geometry for the polymer.

36 MATERIALS SCIENCE↗

Three-Dimensional Printable, Extremely Soft, Stretchable, and Reversible Elastomers from Molecular Architecture-Directed Assembly

3D printing elastomers enables the fabrication of many technologically important structures and devices such as tissue scaffolds, sensors, actuators, and soft robots. However, conventional 3D printable elastomers are intrinsically stiff; moreover, the process of printing often requires external mechanical support and/or post-treatment. In this work, we exploit the self-assembly of a responsive linear-bottlebrush-linear triblock copolymer to create stimuli-reversible, extremely soft, and stretchable elastomers and demonstrate their applicability as inks for in situ direct-write printing 3D structures without the aid of external mechanical support or post-treatment. By developing a procedure for controlled synthesis of such architecturally designed block copolymers, we create elastomers with extensibility up to 600% and Young’s moduli down to ~10 2 Pa, 10 6 times softer than plastics and more than 102 times softer than all existing 3D printable elastomers. Moreover, the elastomers are thermostable and remain to be solid up to 180 °C, yet they are 100% solvent-reprocessable. Their extreme softness, stretchability, thermostability, and solvent-reprocessability bode well for future applications.

36 MATERIALS SCIENCE↗

Mechanically tunable elastomer and cellulose nanocrystal composites as scaffolds for in vitro cell studies

Considering the range of properties that various materials offer for tissue engineering it has come clear that no one size fits all, as no one material can be fully effective for all types of cell and ensuing tissues. Scaffolds need to address the delicate balance between cell-scaffold interactions and the particular requirements of different cell types. To address the specific needs for the controlled growth of tissues it is imperative to match scaffold stiffness and elasticity to cells and tissues of interest to promote regeneration success. We here report an efficient method for creating scaffolds of tunable elasticity by generating a range of composites based on ε-caprolactone-D,L-lactide-based elastomer with cellulose nanocrystals (CNC). Two specific composites with different Young's modulus (E) values (~5 MPa and ~15 MPa) were selected and fully evaluated by tensile tests, Fourier Transform-Infrared (FT-IR), Scanning Electron Microscopy (SEM), contact angle measurements, and X-ray scattering. As a proof of concept this work studies how matching the scaffold's mechanical properties to neuroblastomas and fibroblasts cells affects cell behavior. Specifically, the composite with lower E, by design with less CNC content, is more suitable for neuroblastomas, whereas the one with higher E via higher CNC content is more suited for human dermal fibroblasts. The approach of matching cells with appropriate mechanical environments can provide important insights into fundamental cell behaviors.

36 MATERIALS SCIENCE↗

In-situ X-ray scattering study of isotactic polypropylene/graphene nanocomposites under shear during fused deposition modeling 3D printing

Complementary techniques were applied to characterize the structure property relationships of FDM printed isotactic polypropylene/graphene nanocomposites. Raman spectroscopy indicated that graphene was mostly exfoliated during the nozzle extrusion process. Rheological measurements of the viscosity indicated that the presence of graphene induced shear thinning during extrusion. Azimuthal scans of wide angle x-ray scattering indicate correlated thermal fluctuations of the graphene platelets which stops abruptly at the onset of transcrystallization, or templating of the iPP chains on the graphene. X-ray microbeam SAXS analysis show the formation of ‘shish-kebab’ structures at the core of the unfilled filaments, where the ‘kebab’ component vanishes at the fiber-fiber interface enabling interdiffusion. Weak lamellar structure, and a corresponding decrease in the storage modulus are observed with the addition of 5% graphene. The lamellar structure disappears entirely with the addition of 10% graphene, while the storage modulus is decreased by nearly 50%. Thermal imaging of heat flux dissipation across molded and printed samples shows no orientational effects in pure iPP despite differences in crystal structure. Thermal conductivity increases dramatically in the samples with 10% graphene, and strong orientational effects are observed where the thermal coefficients differ by 180% between samples printed parallel or perpendicular to the heat flux.

36 MATERIALS SCIENCE↗

Molecular Picture of the Transient Nature of Lipid Rafts

In biological membranes, lipid rafts are now thought to be transient and nanoscopic. However, the mechanism responsible for these nanoscopic assemblies remains poorly understood, even in the case of model membranes. Therefore, it has proven extremely challenging to probe the physicochemical properties of lipid rafts at the molecular level. Here, we use all-atom molecular dynamics (MD) simulations and inelastic X-ray scattering (IXS), an intrinsically nanoscale technique, to directly probe the energy transfer and collective short-wavelength dynamics (phonons) of biologically relevant model membranes. We show that the nanoscale propagation of stress in lipid rafts takes place in the form of collective motions made up of longitudinal (compression waves) and transverse (shear waves) molecular vibrations. Importantly, we provide a molecular picture for the so-called van der Waals mediated "force from lipid" [Anishkin, A. et al. Proc. Natl. Acad. Sci. U.S.A. 2014, 111, 7898], a key parameter for the ionic channel mechano-transduction and the mechanism for the lipid transfer of molecular level stress [Aponte-Santamaría, C. et al. J. Am. Chem. Soc. 2017, 139, 13588]. Specifically, we describe how lipid rafts are formed and maintained through the propagation of molecular stress, lipid raft rattling dynamics, and a relaxation process. Eventually, the rafts dissipate through the self-diffusion of lipids making up the rafts. We also show that the molecular stress and viscoelastic properties of transient lipid rafts can be modulated through the use of hydrophobic biomolecules such as melatonin and tryptophan. Overall, the herein proposed mechanism describing the molecular interactions for the formation and dissolution of lipid rafts may offer insights as to how lipid rafts enable biological function.

36 MATERIALS SCIENCE↗

Ultrastructures and Mechanics of Annealed Nephila clavipes Major Ampullate Silk

The semicrystalline protein structure and impressive mechanical properties of major ampullate (MA) spider silk make it a promising natural alternative to polyacrylonitrile (PAN) fibers for carbon fiber manufacture. However, when annealed using a similar procedure to carbon fiber production, the tensile strength and Young’s modulus of MA silk decrease. Despite this, MA silk fibers annealed at 600 °C remain stronger and tougher than similarly annealed PAN but have a lower Young’s modulus. Although MA silk and PAN graphitize to similar extents, annealing disrupts the hydrogen bonding that controls crystal alignment within MA silk. Consequently, unaligned graphite crystals form in annealed MA silk, causing it to weaken, while graphite crystals in PAN maintain alignment along the fiber axis, strengthening the fibers. Finally, these shortcomings of spider silk when annealed provide insights into the selection and design of future alternative carbon fiber precursors.

36 MATERIALS SCIENCE↗

Molecular Architecture Directs Linear–Bottlebrush–Linear Triblock Copolymers to Self-Assemble to Soft Reprocessable Elastomers

Linear–bottlebrush–linear (LBBL) triblock copolymers represent an emerging system for creating multifunctional nanostructures. Their self-assembly depends on molecular architecture but remains poorly explored. We synthesize polystyrene- block -bottlebrush polydimethylsiloxane- block -polystyrene triblock copolymers with controlled molecular architecture and use them as a model system to study the self-assembly of LBBL polymers. Unlike classical stiff rod-flexible linear block copolymers that are prone to form highly ordered nanostructures such as lamellae, at small weight fractions of the linear blocks, LBBL polymers self-assemble to a disordered sphere phase, regardless of the bottlebrush stiffness. Microscopically, characteristic lengths increase with the bottlebrush stiffness by a power of 2/3, which is captured by a scaling analysis. Macroscopically, the formed nanostructures are ultrasoft, reprocessable elastomers with shear moduli of about 1 kPa, two orders of magnitude lower than that of conventional polydimethylsiloxane elastomers. Our results provide insights on exploiting the self-assembly of LBBL polymers to create soft functional nanostructures.

36 MATERIALS SCIENCE↗

In Situ Time-Resolved X-ray Scattering Study of Isotactic Polypropylene in Additive Manufacturing

In this study, we used a specially designed apparatus, which collects simultaneous temperature and X-ray scattering data, to perform in situ measurements of the filament during MatEx 3D printing. The data show that the MatEx 3D printing extrusion process provides sufficient shear to form shish-kebab structures, which initially nucleate at the filament surface and spread into the filament core. Time-resolved measurements show that the kebab component near the surface relaxes after deposition of the second filament and enhances chain diffusion across the interface. SEM images indicate near complete interfacial merging of the filaments, which results in excellent mechanical properties.

36 MATERIALS SCIENCE↗

Martensitic Transformation of Close-Packed Polytypes of Block Copolymer Micelles

Here, we report martensitic shear transformation of strongly segregated block copolymer micelles on face-centered cubic (FCC) lattices to hexagonally close-packed (HCP) structures elucidated by X-ray scattering characterizations. The initial FCC crystal structures of the block copolymer micelles were prepared by direct dissolution of poly(1,2-butadiene-b-ethylene oxide) (PB-PEO) diblock copolymer in the water at 25 °C, and the FCC crystal domains were shear-aligned during the sample preparation process for the X-ray scattering measurements. Heating the shear-aligned FCC crystals of the PB-PEO micelles above 80 °C initiated the transformation to HCP structures, which are also found stable at 25 °C when cooled from the transition temperature. Interestingly, we found that the HCP crystal domains are also aligned, and this suggests that the FCC-to-HCP phase transition has occurred by the martensitic shear transformation. Scattering pattern analysis reveals that the martensitic shear transformation proceeds by preferentially dislocating a specific set of two-dimensional hexagonal close-packed (2D-HCP) layers among four equivalent 2D-HCP layers of the initially shear-aligned FCC crystals. We believe that the selective martensitic shear transformation originates from the orthorhombic-like morphology of the FCC crystal domains formed by slip dislocations and stratifications of initial FCC crystal grains during the sample preparation process. In the shear-aligned FCC crystals with the orthorhombic-like crystal domains, the specific 2D-HCP layers chosen for the martensitic shear transformation have the least area of dislocations, i.e., the least kinetic energy barrier, for the FCC-to-HCP phase transition and appear to be preferentially utilized. These results show that the size and morphology of crystal domains are critical to the formation, stability, and transformation of crystalline structures and consequently control the polymorphism of solid compounds.

36 MATERIALS SCIENCE↗