Engineering topics

Zhong, Yu [Worcester Polytechnic Institute, MA (United States)]

Publications and source records attributed to Zhong, Yu [Worcester Polytechnic Institute, MA (United States)].

3 records

DOE OSTI2025

Optimization of La 2 NiO 4+δ Electrolysis Cell Oxygen Electrode through Surfactant-Enabled LaCoO 3±δ Nanocatalyst Deposition

Lanthanum nickelate (LNO) has shown promise as a Cr-resistant air electrode material for SOECs but has suboptimal surface oxygen exchange properties. Nanocoating of the LNO surface with lanthanum cobaltite (LCO) was chosen to improve cell performance as a surface oxygen conductor. The work focused on the implementation of a two-step nano-LCO film deposition utilizing catechol molecules in a porous LNO electrode. The subgoals of the work were to maintain nanosized LCO particles/ grains to increase active surface area and to control the regularity/ homogeneity of the coating across the microstructure. To achieve these goals, a novel surfactant-enhanced liquid infiltration method was utilized, where nucleation sites were spread across the electrode structure to control the location and size of LCO particles. Various catechol surfactant compositions were evaluated for their ability to control the kinetics of nanoparticle deposition and the homogeneity of the coating. Chelated LCO was characterized by X-ray diffraction (XRD), which found a substantial improvement in LCO formation with surfactant addition and determined polymerized norepinephrine to be the best-performing surfactant, with 88.4% pure LCO formed at low temperature. X-ray photoelectron spectroscopy (XPS) confirmed LCO nanostructures formed by the two-step infiltration process, showing no impurities and a stable perovskite structure. Deposition kinetics were analyzed using atomic force microscopy (AFM), correlating infiltration times and solution molarity to nanoparticle size and distribution, the results of which were confirmed in symmetrical cell samples by scanning electron microscopy (SEM). Electrochemical impedance spectroscopy (EIS) testing demonstrated substantial improvements in polarization resistance, where the nanocoating reduced the resistance by ∼55% to 0.152 Ω·cm 2 at 700 °C and 0.039 Ω·cm 2 at 800 °C. Electrical conductivity relaxation (ECR) at this temperature confirmed an improved surface oxygen exchange coefficient of the LCO + LNO heterostructure predicted by the Bode data from EIS, alongside a reduction in activation energy by about 30%.

Deposition↗

DOE OSTI2025

Hybrid Doping Strategy with High‐Entropy Cu/Fe Surface Modification and Zr Bulk Incorporation for Ni‐Rich Cathodes

A hybrid doping strategy combining Zr 4+ bulk doping with high-entropy Cu 2+ /Fe 3+ surface doping is developed to enhance the structural and interfacial stability of Ni-rich layered oxide cathodes. Cu and Fe are selectively introduced at the particle surface via a surface-selective ion-exchange process, forming a ≈15 nm Fe-rich layer while preserving the layered framework. Compared to the pristine cathode, the hybrid sample exhibits significantly improved electrochemical performance in both half-cell and full-cell configurations. In half-cells, the hybrid retains 88.5% and 90.2% after 100 cycles at 1C under 4.6 and 4.5 V, respectively. During high-voltage full-cell cycling, the hybrid cathode maintains over 80% capacity retention, whereas the pristine counterpart retains less than 10% under identical conditions over the same cycling period. XPS, EELS, and DEMS analyses confirm improved oxygen retention, suppressed gas evolution, and stable surface chemistry, while DFT calculations indicate enhanced Me–O bonding in the selected Fe 0.75 Cu 0.25 (Mn 1/16 Co 2/16 Ni 13/16 )O 2 surface composition, which is identified through DFT-calculated mixing energy reaching a minimum at this ratio, indicating the most thermodynamically favorable configuration. In conclusion, these results demonstrate the effectiveness of this hybrid doping strategy in mitigating coupled degradation pathways in Ni-rich cathodes.

15 GEOTHERMAL ENERGY↗

DOE OSTI2025

Anionic‐Based Layered Oxide Cathodes with High Electrochemical Performance through Dual‐Site Substitutions for Sodium‐Ion Batteries

Mn-rich layered oxide cathodes with anionic redox promise high energy density for sodium-ion batteries (SIBs) due to ultra-high capacity derived from both Mn and O redox couples. Nevertheless, instability of the reactions that lead to poor electrochemical stability hinders the cathodes from practical applications. Here, the Al and Zn dual-site substitution strategy is proposed to enhance electrochemical performance. Here, the designed cathode, Na 0.73 Zn 0.03 Li 0.25 Mn 0.76 Al 0.01 O 2 (AlZn), delivers a high discharge capacity of 242 mAh g −1 with an impressive rate capability (162 mAh g −1 at 1000 mA g −1 ) and excellent capacity retention (89.69% over 150 cycles). In addition, full-cell SIB based on AlZn coupled with hard carbon exhibits a high energy density of 317 Wh kg −1 (based on both cathode and anode mass) and a reasonable capacity retention of 80.8% after 250 cycles. Revealed by advanced investigations, the synergy of robust Al–O in TM layers and O–Zn–O pillars in Na layers helps alleviate severe inactive spinel/rock-salt phase transformation and intragranular cracks in the AlZn cathode. This consequently leads to greatly enhanced electrochemical performance over the pristine cathode. This work provides insight into improving electrochemical properties of anionic-redox-based layered oxides by Al/Zn co-substitutions toward high-energy SIBs.

25 ENERGY STORAGE↗