Interstitial Lithium Doping in BiVO4 Thin Film Photoanode for Enhanced Solar Water Splitting Activity
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Zhou, C.
Explore the source record for details and available documents.
A recent study on the intrinsic magnetic properties of CeFe11-yCoyTi has revealed that substituting one Co for Fe retains the favorable magnetocrystalline anisotropy H-a found in the ternary Fe end member, while enhancing the Curie temperature T-c and saturation magnetization 4 pi M-s. These findings warrant further optimization around Co substitution y = 1 to try to exploit the hard magnetic properties of these Ce-based magnets. Both Ce and Co concentrations in Ce1+xFe11-yCoyTi have been optimized in the range of x = 0 0.2 and y = 0 1.5. It was found that Co substitution effectively enhances all hard magnetic properties, although the values are still lower than those predicted from the intrinsic magnetic properties. Specifically, Tc increases from 210 degrees C to 285-350 degrees C; 4 pi M-19 (magnetization at 19 kOe) from 8.9 kG to 10.5-11.5 kG, remanence B-r from 3.1 kG to 4.1-4.5 kG, and most importantly, H-ci from 1.1 kOe to 1.5 kOe. As a result, the room temperature energy product (BH)(max) has been increased by over 100% from 0.7 MGOe in Ce1.1Fe11Ti to 1.5 MGOe in Ce1.05Fe9.75Co1.25Ti. Microscopy analysis indicates that the addition of Co refines the grain size and promotes chemical homogeneity at the microscopic scale. The beneficial effect of Co on the microstructure contributes to the improved hard magnetic properties. (C) 2015 AIP Publishing LLC.
Explore the source record for details and available documents.
We report the discovery of ternary CeFe(12-x)Si(x)compounds possessing the ThMn12 structure. The samples were prepared by melt spinning followed by annealing. In contrast to other known Ce Fe-based binary and ternary compounds, CeFe12-xSix compounds exhibit exceptionally high Curie temperatures whose values increase with added Si substitution. The highest T. = 583 K in CeFe10Si2 rivals that of the well-established Nd2Fe14B compound. We ascribe the T-c behavior to a combination of Si-induced 3d band structure changes and partial Ce3+ stabilization. (C) 2014 Published by Elsevier Ltd.
New quaternary alloys of Ce-1 xNdxFe12 Mo-y(y) with x=0, 0.2, 0.4, 0.6, 0.8, 1 and y=0, 1.5, 2 have been prepared and magnetically hardened by melt spinning. X-ray diffraction indicates that the as-spun materials exhibit the tetragonal ThMn12-type structure. Prior to nitriding, the coercivity H-ci is less than 0.6 kOe in all alloys and is independent of Nd content, while the magnetization 4 pi M-19 (measured in an applied held of 19 kOe) and Curie temperature T-c increase with added Nd content x. The effects of nitriding pressure P, time t, and temperature TOR magnetic properties have been carefully evaluated on NdFe10Mo2 in order to identify the optimal nitriding parameters. The optimized nitriding profile was subsequently adopted to nitride the remaining samples. After nitrogenation, T-c and 4 pi M-19 have been substantially enhanced primarily due to the increased Fe-Fe exchange from nitrogen induced lattice dilation. Benefitting from the positive contribution from Nd, H-ci has been greatly improved in the Nd containing samples. As a result, Ce0.2Nd0.8Fe10Mo2 nitride features H-ci=2.9 kOe and (BH)(max) = 1.6 MGOe and Ce0.2Nd0.8Fe10.5Mo1.5 nitride demonstrates H-ci=2.5 kOe, (BH)(max) = 1.5 MGOe at room temperature, and T-c=337 degrees C. which are substantial advancements compared to the pure Ce based ThMn12-type materials previously reported. (C) 2014 Published by Elsevier B.V.
A series of novel alloys CeFe11-xCoxTi (0 <= x <= 11) with ThMn12 structure has been successfully prepared by melt-spinning. The Curie temperature T-c increases with Co content x, reaching a maximum of 689 degrees C at x = 9 and declining to 664 degrees C at complete Co filling (x = 11). The room temperature saturation magnetization 4 pi M-s and magnetocrystalline anisotropy H-a have been estimated by fitting the first quadrant demagnetization curve with the Stoner-Wohlfarth model. 4 pi M-s first increases with increasing Co up to x = 3, then decrease. H-a has a complex dependence on Co content, which is indicative of a change in the easy magnetization direction from axis to plane and back as the Co content increases. (C) 2014 AIP Publishing LLC.
We report the magnetic hardening of CeFe12-xMox by melt spinning at surface wheel speeds between 10 m/s and 30 m/s. The synthesis range of CeFe12-xMox has been extended to CeFe11Mo, which uses the least amount of Mo substitution to stabilize the ThMn12-type structure. X-ray diffraction indicates that as-spun samples are multi-phased, typically consisting of a primary ThMn12-type phase with impurity phases of Fe-Mo alloy, Ce2Fe17 and CeFe2. However, nearly pure ThMn12-type phase can be obtained either by directly melt spinning at specific wheel speeds or by annealing the over-quenched ribbons at an optimum temperature. The magnetic moment of CeFe12-xMox is found to be affected not only by the number of Fe atoms but also by weakening of the Fe moment from Mo substitution. Nitriding is effective in enhancing the Curie temperature T-c and saturation magnetization 4 pi M-s. Tc was enhanced by at least 151 degrees C after nitrogenation for all compositions. The newly identified CeFe11Mo compound exhibits the best magnetic properties in the alloy series, having T-c = 370 degrees C and 4 pi M-s > 13.0 kG after nitriding and (BH)(max) = 0.3 MGOe after annealing. (C) 2013 Published by Elsevier B.V.
We report the discovery of a new ternary compound prepared by melt spinning induction melted ingot of nominal composition CeFe11Zr. The sample melt spun at v(s) = 25 m/s exhibits the hexagonal TbCu7-type structure of space group P6/mmm. Through fitting the experimental X-ray diffraction pattern by Rietveld method, we have successfully derived the crystal structure of the new compound melt spun at v(s) = 25 m/s to be CeFe10Zr0.8. Subsequent density function theory calculation fully supports the chemical stability of the new ternary compound. Annealing test showed that the melt spun CeFe10Zr0.8 is stable up to 700 degrees C and annealing at higher temperature would cause it to decompose into hexagonal Ce2Fe17-type structure and ZrFe2. The Curie temperature measurement found that CeFe10Zr0.8 boasts a T-c = 181 degrees C, which is higher than the Tc values of all known Ce-Fe binary compounds, and 30 degrees C higher than that of Ce2Fe14B. These interesting properties stimulate continued search for new Ce-based permanent magnets that could be a cost effective solution to engineering needs in the future. (c) 2013 Elsevier B.V. All rights reserved.
Rare earth compounds RFe12_xMx with tetragonal ThMn12-type structure are of great research interest for potential applications as permanent magnets. These materials are known to serve as the precursors for nitriding and hydriding processes which in certain conditions can dramatically increase the Curie temperature, spontaneous magnetization, and affect the magnetic anisotropy. In this paper, we report the phase study of CeFe10.5Mo1.5 samples melt spun at various surface wheel speeds vs between 5 m/s and 60 m/s. The results from quantitative Rietveld analysis indicate that the as-spun ribbons are a mixture of primary CeFe10.5Mo1.5 phase with impurity phases such as Ce2Fe17, Fe-Mo alloy and CeFe2. When the wheel speed vs is below 25 m/s, CeFe10.5Mo1.5 phase accounts for greater than 85 wt% in the as-spun ribbons, while the Fe-Mo alloy is the only detectable impurity phase. Above v(s)=25 m/s, as the wheel speed increases, CeFe10.5Mo1.5 phase decreases monotonically to about 60 wt% at v(s)=6O m/s while the amounts of impurity phases increase. Thermogravimetric measurement indicates that the Curie temperature T-c. corresponding to CeFe10.5Mo1.5 phase is 341 K. As a result, the best performing sample melt spun at v(s),=15 m/s only exhibits an energy product BHmax=0.121 MGOe at room temperature. Although such a number is modest for a permanent magnet, further nitriding is expected to greatly enhance the Curie temperature, and hence the magnetic performance. (C) 2013 Elsevier B.V. All rights reserved.
The behaviour of interstitial impurities(C,O,N,H) on the Nb surface with respect to grain boundaries may affect cavity performance. Large grain Nb makes possible the selection of bicrystal samples with a well defined grain boundary. In this work, Dynamic SIMS was used to analyze two Nb bicrystal samples, one of them heat treated and the other non heat treated (control). H levels were found to be higher for the non heat treated sample and a difference in the H intensity and sputtering rate was also observed across the grain boundary for both the samples. TEM results showed that the bicrystal interface showed no discontinuity and the oxide layer was uniform across the grain boundary for both the samples. TOF-SIMS imaging was also performed to analyze the distribution of the impurities across the grain boundary in both the samples. C was observed to be segregated along the grain boundary for the control sample, while H and O showed a difference in signal intensity across the grain boundary. Crystal orientation appears to have an important role in the observed sputtering rate and impurity ion signal differences both across the grain boundary and between samples
Most of the currently used methods for protein function prediction rely on sequence-based comparisons between a query protein and those for which a functional annotation is provided. A serious limitation of sequence similarity-based approaches for identifying residue conservation among proteins is the low confidence in assigning residue-residue correspondences among proteins when the level of sequence identity between the compared proteins is poor. Multiple sequence alignment methods are more satisfactory - still, they cannot provide reliable results at low levels of sequence identity. Our goal in the current work was to develop an algorithm that could overcome these difficulties and facilitate the identification of structurally (and possibly functionally) relevant residue-residue correspondences between compared protein structures. Here we present StralSV, a new algorithm for detecting closely related structure fragments and quantifying residue frequency from tight local structure alignments. We apply StralSV in a study of the RNA-dependent RNA polymerase of poliovirus and demonstrate that the algorithm can be used to determine regions of the protein that are relatively unique or that shared structural similarity with structures that are distantly related. By quantifying residue frequencies among many residue-residue pairs extracted from local alignments, one can infer potential structural or functional importance of specific residues that are determined to be highly conserved or that deviate from a consensus. We further demonstrate that considerable detailed structural and phylogenetic information can be derived from StralSV analyses. StralSV is a new structure-based algorithm for identifying and aligning structure fragments that have similarity to a reference protein. StralSV analysis can be used to quantify residue-residue correspondences and identify residues that may be of particular structural or functional importance, as well as unusual or unexpected residues at a given sequence position.
Abstract not provided
In FY09 they will (1) complete the implementation, verification, calibration, and sensitivity and scalability analysis of the in-cell virus replication model; (2) complete the design of the cell culture (cell-to-cell infection) model; (3) continue the research, design, and development of their bioinformatics tools: the Web-based structure-alignment-based sequence variability tool and the functional annotation of the genome database; (4) collaborate with the University of California at San Francisco on areas of common interest; and (5) submit journal articles that describe the in-cell model with simulations and the bioinformatics approaches to evaluation of genome variability and fitness.
In this work we developed new code for detecting putative multi-domain protein-protein interactions for a small network of bacterial pathogen proteins, and determined how structure-driven domain-fusion (DF) methods should be scaled up for whole-proteome analysis. Protein-protein interactions are of great interest in structural biology and are important for understanding the biology of pathogens. The ability to predict protein-protein interactions provides a means for development of anti-microbials that may interfer with key processes in pathogenicity. The function of a protein-protein complex can be elucidated through knowledge of its structure. The overall goal of this project was to determine the feasibility of extending current LLNL capabilities to produce a high-throughput systems bio-informatics capability for identification and characterization of putative interacting protein partners within known or suspected small protein networks. We extended an existing LLNL methodology for identification of putative protein-protein interacting partners (Chakicherla et al (in review)) by writing a new code to identify multi-domain-fusion linkages (3 or more per complex). We applied these codes to the proteins in the Yersinia pestis quorum sensing network, known as the lsr operon, which comprises a virulence mechanism in this pathogen. We determined that efficient application of our computational algorithms in high-throughput for detection of putative protein-protein complexes genome wide would require pre-computation of PDB domains and construction of a domain-domain association database.
Synchronization processes in populations of locally interacting elements are in the focus of intense research in physical, biological, chemical, technological and social systems. The many efforts devoted to understand synchronization phenomena in natural systems take now advantage of the recent theory of complex networks. In this review, we report the advances in the comprehension of synchronization phenomena when oscillating elements are constrained to interact in a complex network topology. We also overview the new emergent features coming out from the interplay between the structure and the function of the underlying pattern of connections. Extensive numerical work as well as analytical approaches to the problem are presented. Finally, we review several applications of synchronization in complex networks to different disciplines: biological systems and neuroscience, engineering and computer science, and economy and social sciences.