Electrically conductive hot mix asphalt mixtures for salt-free snow/ice-melting pavements heated with direct electric energy: A comparison between utilizing carbon-based aggregate and fiber
Not Available
Engineering topics
Publications and source records attributed to Zhou, Hongyu.
Not Available
Timely removal of ice and snow from roads is critical to safe, fast, and uninterrupted transportation networks in cold regions. Constructing electrically conductive asphalt pavements to melt the ice and snow on the roads through resistive eating is an emerging alternative technology to traditional snow/ice removal approaches such as utilizing snowplow machines and deicing chemicals. Carbon-based fibers and fillers including carbon fiber and graphite have been widely reported to make electrically conductive hot mix asphalt mixtures for pavement snow/ice-melting applications. This study aimed to develop and demonstrate a novel type of electrically conductive asphalt pavements for snow/ice-melting, which utilizes electrically conductive cold mix asphalt (CMA) mixtures incorporating coal-derived carbon-based coke aggregate as resistive heating elements. Both laboratory experiments and field tests were conducted to investigate the electrical, mechanical, and thermal properties of such electrically conductive asphalt mixtures and pavements. The laboratory experiment results indicated that the electrically conductive CMA mixtures incorporating coke aggregate had sufficiently high electrical conductivity and satisfactory mechanical performance and the pavement prototype slab utilizing a thin layer of such CMA mixtures could successfully raise the pavement surface temperatures to 8.3–11.7 °C rom a low temperature of –5 °C with an input power density of 473 W/m 2 . The field test results showed that the full-scale coal-derived electrically conductive asphalt pavements were able to increase the pavement surface temperatures when electricity was applied, but the magnitude of temperature increase was highly dependent on the power density. Furthermore, it is promising to use coke aggregate to construct coal-derived electrically conductive asphalt pavements for snow/ice melting.
This project focused on developing an eco-friendly, multifunctional pavement system, called Coal-Derived Carbon Enabled Smart Pavement (CDC-SP), using coal-derived materials. The system utilizes coal-derived pyrolyzed char as a key component to create electrically conductive asphalt concrete for smart pavements that offer self-heating, self-sensing, and self-healing capabilities. These functions are made possible by the conductive properties of coal-char, which enable Ohmic heating for snow and ice deicing, piezoresistivity for self-sensing, and induction heating for self-healing of cracks caused by stress or aging. The team successfully created CDC-SP samples with over 50% coal char composition, demonstrating desirable mechanical properties such as rutting resistance, moisture susceptibility, and cracking resistance. These samples also exhibited strong electrical and thermal conductivity, making them ideal for heating applications. Extensive tests confirmed the pavement’s effectiveness in melting ice and snow and maintaining durability under environmental conditions. The CDC-SP presents a promising approach to integrating U.S. domestic coal resources into infrastructure projects, providing environmental and economic benefits by enhancing pavement performance while utilizing low-cost coal-derived materials. Further research and compliance with industry standards are recommended before commercial scaling.
Existing pavement de-icing methods result in high installation and maintenance costs, traffic delays, excessive weariness and corrosion, and negative environmental and safety impacts. To overcome these challenges, this paper presents an innovative pathway to designing and constructing smart self-heating pavements using a low-cost coal-char bearing asphalt material. The conductive asphalt incorporates coal char, i.e., a key byproduct of the coal pyrolysis process, into the Stone Mastic Asphalt (SMA) mixture. This asphalt containing coal-derived solid carbon exhibits highly tailorable electrical conductivity, satisfactory mechanical and thermophysical properties, and superior cost-efficiency as compared to other conductive pavement materials. The de-icing performance was also demonstrated by laboratory experiments on a bench-scale prototype. Furthermore, an efficient thermal network model was developed and validated by experiments to investigate the transient thermal behavior and energy performance of the Ohmic heating pavement system. Furthermore, the whole-year energy simulation case studies were conducted on a bridge pavement with an annual energy use of 24.6–1444.8 kWh/m 2 , showcasing its potential in field applications across cool humid, cold humid, and subarctic/arctic climate zones.
Here, this paper studies the pathways to formulate lightweight and ultra-lightweight 3D printable cementitious composites. A hybrid approach was proposed by combining the advantages of traditional chemical-induced foaming (foaming approach) and lightweight particulate inclusions (synthetic foam approach). A comprehensive experimental program was conducted to evaluate the effects of foaming agents and fly ash cenosphere (FAC) on the printability, microstructure, mechanical and thermal properties of 3D printed samples. The results showed that the hybrid approach could produce a mixture with a density as low as 470 kg/m 3 while ensuring good flowability and buildability owing to the lubricating effect of foaming and supporting skeleton formed by FAC. In addition, a three-step homogenization procedure was also developed to predict the effective elastic modulus and thermal conductivity of 3D printable cementitious composites and cementitious foam. The findings of the study highlighted the effectiveness of the hybrid approach in formulating 3D printable ultra-lightweight cementitious composites in thermal insulation and acoustic applications.
Not Available
Modifying asphalt is a potentially high-value application for reusing waste plastics because of the high-volume usage of asphalt in highway construction. However, simply blending hot plastics and asphalt encounters difficulties related to the poor solubility of polymers, which limits the formation of a swollen network with asphalt molecules. The polymer phases also tend to coalesce and separate from asphalt during high-temperature storage in static conditions. The present study developed an innovative process to stabilize waste plastics in asphalt and improve binder storage stability by using lightly pyrolyzed crumb rubber together with a chemical compatibilizer. Both polymers were extruded to produce a thermoplastic elastomer (TPE) for asphalt modification. The mechanical performance and chemical reactions of TPEs were characterized via tension test and Fourier transform infrared spectroscopy. The storage stability and rheological properties of modified binder blends were evaluated through laboratory asphalt stability test and dynamic shear rheometer test. Polymer phases and network structures were characterized through optical microscopy. It was found that the pyrolyzed and reactive extrusion process improved the rubber solubility and polymer interaction, and therefore the storage stability of modified binder blends. The co-existence of rigid plastic and soft rubbery regimes in an entangled network provided a promising pathway to improve the mechanical performance of asphalt binders in both high- and low-temperature domains.
Low-income households generally experience a high energy burden; however, the factors influencing energy burdens are beyond socio-economics. This study explores the relationships between the multidimensionality of community vulnerability factors and energy burden across multiple geospatial levels in the United States. Our study found the distribution of energy burden in 2020 showed a great deal of variety, ranging from a minimum of 2.93 % to a maximum of 30.45 % across 3142 counties. The results of non-spatial and spatial regressions showed that the vulnerability ranks of socioeconomic, household composition and disability, minority and language, household type and transportation, and COVID mortality rate are significant predictors of energy burdens at the national level. However, at the regional level, only socioeconomic, minority and language significantly influence energy burdens. Minority and language negatively impact energy burdens except for the South East-Central region. Additionally, our analyses highlight the need to consider community vulnerability indicators' spatial homogeneity and heterogeneity. At the national level, only the epidemiological factors index is a spatially homogeneous predictor; on the regional and state level, the spatially homogeneous predictors such as socioeconomic status, household composition and disability, and household type and transportation vary by region. Such a region-sensitive relationship between energy burden and the predictors indicates spatial heterogeneity. Here this study suggests policy recommendations through the lens of the multidimensionality of community vulnerability factors. Implementing flexible national energy policies while making particular energy assistance policies for the vulnerable population at the regional or state levels is essential.
Not Available
Value-added utilization of waste tires in cementitious materials has been studied for decades, whereas the synergy between rubber and alkali-activated cements deserves more investigations. To this end, we compared physico-mechanical and durability properties of alkali-activated slag (AAS) and OPC-based composites containing NaOH-pretreated/as-received crumb rubber (CR). It was found that the incorporation of CR had both positive and negative effects on specimens due to its special attributes. CR reduced electrical conductivity which was associated with the ion transport ability, since it worked as an electrical insulator and increased hydrophobicity of pore walls. The sulfate expansion decreased with CR content because the flow of sulfate ions was demobilized, and the flexibility of CR relieved the internal stress. CR also improved the freeze-thaw durability of composites if the total CR content was less than 30% in specimens. However, the low Young's modulus of CR impaired the compressive strength and failed to effectively control the total shrinkage upon drying. The composites with CR must avoid high temperature exposure which resulted in the pyrolysis of rubber. In addition, the NaOH pretreatment enhanced adhesion between CR and hydrated cement and improved overall performances of composites. The FTIR spectra confirmed the NaOH-induced accelerated oxidation of CR surface and the generation of polar functional groups including carbonyl and carboxyl groups, increasing the total surface energy of rubber. More importantly, the alkali-activation process for AAS could treat the CR aggregate in the meantime, which means the use of CR in alkali-activated cements does not require the pretreatment of CR before blending.
This paper delineates the feasibility of incorporating microencapsulated phase change materials (mPCM) into 3D printable cementitious composite materials. A comprehensive experimental program was carried out to evaluate the impacts of mPCM on the printability, microstructures, mechanical and thermal properties of cementitious 3D printing ‘inks’. Results showed that the mPCM affected the printability of the cementitious ink material based on its physical properties (e.g., particle size) and volume loading – at lower volume loadings, mPCM increased the flowability of the cementitious ink material while leading to increased compressive strength and thermal conductivity for the hardened printed material. However, further increase in mPCM dosage led to a decrease in printability and, therefore, decrease in compressive strength and thermal conductivity as compared to the reference mixture. Here the results also showed that the inclusion of mPCM influence the printing parameters. In general, the inclusion of higher volume contents of mPCM necessitates a higher extrusion rate to achieve a desirable extrudability. Lastly, a thermal network model was formulated for 3D printed mPCM charged building components (e.g., wall). The study shows that microencapsulated PCM materials have good potential to be used in 3D printable cementitious mixtures for improving the thermal and energy performance of 3D printed buildings.
Crumb rubbers (CR) and recycled Polyethylene (PE) are commonly used as modifiers to improve the asphalt properties. However, the addition of these modifiers individually may result in phase separation of PE and inadequate degradation of CR, which may not simultaneously satisfy the rheological and aging resistance of the binder blends. In this study, a type of CR/PE composites manufactured through melt extrusion procedures was adopted for the improvement of the modified binder blends. The modified binder blends after short-term (RTFO) and long-term (PAV) aging were collected for dynamic shear rheometer and bending beam rheometer tests. FTIR tests were also used to quantify the aging resistance, while differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were applied to evaluate the thermal behaviors of the binder blends. Optical microscopy tests were used to explore the modification mechanism and visualize the microstructures of original and PAV aged binder blends. Test results showed that CR/PE composites could significantly improve the aging resistance of the binder blends. The dispersed PE particles still interacted with each other and meanwhile worked with the diffused rubbery phase, which could form a similar TPEs network. The oxidation and high-temperature aging of such binder blends would strengthen the network that resisted the aging severity of the binder blends. Furthermore, it was also revealed that CR/PE modified asphalt could sustain more heat before a rapid degradation and the well-dispersed PE particles could interact with the diffused CR particles to form a network to resist aging.
Herein, this paper presents a life-cycle cost (LCC) informed co-design framework for building structures and envelope systems, holistically considering the influences of energy and natural hazard performance. The proposed method is consisted of a two-stage design and decision-making process, aiming to provide a quantitative guideline for building's structural and envelope co-design based on the its geographic locations. First, the building's structural configuration and envelope type are selected based on the life cycle cost. Then, the long-term cost effectiveness of various energy-saving building envelope options (e.g., high-performance glazing and insulation) is evaluated to refine the envelope design. The proposed co-design framework was demonstrated through the case study of a medium-size office building archetype in three locations with distinct climate conditions and seismic activities (i.e., Los Angeles, Memphis, and Boston). The results highlighted the interplay between building's structural (seismic) performance and the cost-effectiveness of energy-saving design options – e.g., for buildings located in high-seismic regions, seismic enhancing designs greatly reduce the paybak period of high performance building envelope by reducing the seismic loss; whereas for buildings located in regions with cold climate and low seismic risk such as Boston, spatial frame with high insulation building envelope shows the lowest LCC.
The hot box test method has been applied to evaluate both the steady-state (U-value) and dynamic thermal properties of building envelopes. However, the high construction cost of full-scale hot box apparatus and the testing time required (usually several days) may prevent its wider adoption. To overcome the limitations of full-scale hot box tests, here we propose a novel method to evaluate the dynamic thermal performance of building envelope components using a small-scale calibrated hot box and scaled-down specimen. In this paper, the scaling relationships of thermal properties evaluated using a full-size specimen and a scaled-down specimen are established based on the Laplace transform of the heat transfer equations. In addition, dynamic thermal properties obtained from scaled-down experimental tests are compared to the values calculated by the EN ISO13768 (ISO) method. A small-scale hot box with a 355 mm × 355 mm metering area was constructed and calibrated to validate the correlations. Three scaled-down concrete sandwich wall panels were then tested and the scaling relationship was cross-validated using the experimental results, finite difference (FD) simulations, and the ISO method. The results indicate that the dynamic thermal properties obtained from a scaled-down hot box test can be correlated to its full-size counterpart when certain conditions are met. The scaled-down hot box test is demonstrated to be an effective yet economical alternative to a full-scale test with significantly reduced experimentation cost and turn-around time.
Not provided.
This work studies the evolution of elastic and thermal properties of cementitious composites containing micro-size lightweight fillers after exposure to elevated temperatures (up to 800 °C). A multiscale investigation is carried out to study the thermal degradation of cementitious composite materials at multiple scale levels: at cement past level, the dehydration kinetics of cement hydrates (i.e., C–S–H, CH and aluminate hydrates) and development of microcracks are studied as functions of exposure temperatures. The damage mechanism of the inclusion phases and damages within the interfacial transition zone (ITZ) under elevated temperature are also investigated. In addition, the change of mechanical (i.e., elastic moduli, compressive strengths) and thermal (thermal conductivities) properties are measured as functions of the exposure temperature. Based on the experimental studies, a multiscale thermal degradation model is developed where the thermal degradations of cement paste (including water composition, porosity, and solid phase changes), inclusion phases, and the interfaces are captured through a multiscale sub-stepping homogenization scheme. The thermal degradation model is validated through multiple sets of experimental data. Finally, the influence of key parameters including the particle size distribution of the inclusions, the chemical composition, as well as the effects of ITZ damage are studied.
The development of insulation materials with low effective thermal conductivity is essential for energy savings in various applications, including buildings, food services, pipe insulation, and refrigeration. Such materials can be developed by using micro- or nanoporous structures, as well as low-thermal conductivity gases and/or reduced pressure. A variety of effective medium approximation (EMA) models have been developed to study thermal transport through solid in porous structures. However, in many cases, the impacts of porosity on solid conduction are not well predicted by EMA models because of the assumptions made for simplification. Furthermore, the results can vary by a factor of up to 1.5, depending on the morphology of the pores. Hence, proper guidance is needed to choose the appropriate EMA model for a given morphology. This work presents a finite element method study using COMSOL Multiphysics software for various geometries, including hollow cubes, overlapping hollow spheres (normally stacked and tightly packed), and Voronoi structures, and compares the results to those obtained from various EMA models. Simulation results for the hollow cubes and Voronoi structures matched well with the Maxwell-Eucken and Russell model. The results for hollow spheres closely matched the Bauer model and the Glicksman model with fitting parameters. This work provides guidance on analyzing and designing insulation materials for energy savings in the future.