Search NASA⌕ Search

Engineering topics

Zhou, L.

Publications and source records attributed to Zhou, L..

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Successive magnetic orderings in the Ising spin chain magnet DyNi 5 Ge 3

In this report, we investigated a new rare-earth-based one-dimensional Ising spin chain magnet DyNi 5 Ge 3 by means of magnetization, specific heat, and powder neutron diffraction measurements. Due to the crystalline electrical field splitting, the magnetic Dy ions share an Ising-like ground doublet state. Owning to the local point symmetry, these Ising moments form into two canted magnetic sublattices, which were further confirmed by the angle-dependent magnetization measurement. In zero fields, two successive antiferromagnetic phase transitions were found at temperatures T N1 =6K and T N2 =5K, respectively. Only part of the moments are statically ordered in this intermediate state between T N1 and T N2 . Powder neutron diffraction experiments at different temperatures were performed as well. Further, an incommensurate magnetic propagation vector of k m =(0.5,0.4,0.5) was identified. The refined spin configurations through the irreducible representation analysis confirmed that these Ising spins are canted in the crystal ab plane.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quantum optimization of maximum independent set using Rydberg atom arrays

Realizing quantum speedup for practically relevant, computationally hard problems is a central challenge in quantum information science. Using Rydberg atom arrays with up to 289 qubits in two spatial dimensions, we experimentally investigate quantum algorithms for solving the maximum independent set problem. We use a hardware-efficient encoding associated with Rydberg blockade, realize closed-loop optimization to test several variational algorithms, and subsequently apply them to systematically explore a class of graphs with programmable connectivity. We find that the problem hardness is controlled by the solution degeneracy and number of local minima, and we experimentally benchmark the quantum algorithm’s performance against classical simulated annealing. On the hardest graphs, we observe a superlinear quantum speedup in finding exact solutions in the deep circuit regime and analyze its origins.

Science & Technology - Other Topics↗
NASA NTRS1996

Effect of Tilt Angle on the Morphology of SiC Epitaxial Films Grown on Vicinal (0001) SiC Substrates

In this study of 4H-SiC and 6H-SiC epitaxial films we found that film morphology was strongly dependent on the tilt angle of the substrate. Large surface steps (up to 25 nm high) due to step bunching were more prevalent at smaller tilt angles. Also, 4H films were more susceptible than 6H to 3C-SiC inclusions during growth. The lateral growth of steps from screw dislocations in low-tilt-angle substrates demonstrated that step bunching on the atomic scale was anisotropic with respect to growth direction for both 4H-SiC and 6H-SiC. A model explaining this behavior is presented. We observed and directly measured the Burgers vector of a 'super' screw dislocation in a 6H-SiC epilayer.

Powell, J. A.↗
NASA NTRS1993

Influence of recreational activity and muscle strength on ulnar bending stiffness in men

Bone bending stiffness (modulus of elasticity [E] x moment of inertia [I]), a measure of bone strength, is related to its mineral content (BMC) and geometry and may be influenced by exercise. We evaluated the relationship of habitual recreational exercise and muscle strength to ulnar EI, width, and BMC in 51 healthy men, 28-61 yr of age. BMC and width were measured by single photon absorptiometry and EI by mechanical resistance tissue analysis. Maximum biceps strength was determined dynamically (1-RM) and grip strength isometrically. Subjects were classified as sedentary (S) (N = 13), moderately (M) (N = 18), or highly active (H) (N = 20) and exercised 0.2 +/- 0.2; 2.2 +/- 1.3; and 6.8 +/- 2.3 h.wk-1 (P < 0.001). H had greater biceps (P < 0.0005) and grip strength (P < 0.05), ulnar BMC (P < 0.05), and ulnar EI (P = 0.01) than M or S, who were similar. Amount of activity correlated with grip and biceps strength (r = 0.47 and 0.49; P < 0.001), but not with bone measurements, whereas muscle strength correlated with both EI and BMC (r = 0.40-0.52, P < 0.005). EI also correlated significantly with both BMC and ulnar width (P < 0.0001). Ulnar width and biceps strength were the only independent predictors of EI (r2 = 0.67, P < 0.0001). We conclude that levels of physical activity sufficient to increase arm strength influence ulnar bending stiffness.

NASA Discipline Musculoskeletal↗
NASA NTRS1993

Effects of Gravity on the Transition to Turbulence of Gas Jet Diffusion Flames

An ongoing study of the transition to turbulence of gas jet diffusion flames conducted in a reduced microgravity environment at the NASA Lewis 2.2 second drop tower is described. The experiments were based on propane injected into quiescent air. Several differences with the corresponding normal gravity process were observed. In particular, large scale structures appeared intermittently in microgravity which are manifested at the flame base and convected down stream. As the Reynolds number increased, a continuous train of structures was observed along the flame front. These observations are explained by instability of the shear layer associated with injection of flow into quiescent surroundings.

Bahadori, M. Y.↗