Engineering topics
Publications and source records attributed to Zhou, Lin.
Single-atom metal embedded in nitrogen-doped carbon show high HER performance, with Co-NAC reaching 200 mA cm −2 at 310 mV overpotential.
The performance of superconducting qubits is often limited by dissipation and two-level systems (TLS) losses. The dominant sources of these losses are believed to originate from amorphous materials and defects at interfaces and surfaces, likely as a result of fabrication processes or ambient exposure. Here, we explore a novel wet chemical surface treatment at the Josephson junction-substrate and the substrate-air interfaces by replacing a buffered oxide etch (BOE) cleaning process with one that uses hydrofluoric acid followed by aqueous ammonium fluoride. We show that the ammonium fluoride etch process results in a statistically significant improvement in median $\text{T}_1$ by $\sim22\%$ (p = 0.002), and a reduction in the number of strongly-coupled TLS in the tunable frequency range. Microwave resonator measurements on samples treated with the ammonium fluoride etch after niobium deposition and etching also show $\sim33\%$ lower TLS-induced loss tangent compared to the BOE treated samples. As the chemical treatment primarily modifies the Josephson junction-substrate interface and substrate-air interface, we perform targeted chemical and structural characterizations to examine materials differences at these interfaces and identify multiple microscopic changes that could contribute to decreased TLS losses.
Explore the source record for details and available documents.
SQMS Nanofabrication Taskforce, which brings together experts in nanofabrication and materials science at the SQMS Center, has been launched to implement novel materials, substrates, and fabrication techniques for high coherence superconducting quantum devices. In a first coordinated effort, the Nanofabrication Taskforce developed fabrication processes to eliminate the lossy materials at surfaces and interfaces of superconducting qubits to enhance qubit coherence. The initial results of this study demonstrated T1 enhancement by almost an order of magnitude with best T1 s reaching ~ 600 $\mu$s. [1] We attribute this improvement to the replacement of lossy native Nb oxide layer with native Ta oxide, which is thinner and less disordered. we are now currently working on strategies with an aim towards moving qubit coherence times to millisecond timescales and beyond. The results of a systematic study will be presented to address substrate preparation, alternative materials as low loss platforms (Nb, Ta, and Re), novel non-oxide forming low loss capping layers such as proximitized Au, optimized qubit designs, and optimized Josephson junction materials, processing, and design.
Magnetic dopants in three-dimensional topological insulators (TIs) offer a promising avenue for realizing the quantum anomalous Hall effect (QAHE) without the necessity for an external magnetic field. Understanding the relationship between site occupancy of magnetic dopant elements and their effect on macroscopic property is crucial for controlling the QAHE. By combining atomic-scale energy-dispersive X-ray spectroscopy (EDS) maps obtained by aberration-corrected scanning transmission electron microscopy (AC-STEM) and novel data processing methodologies, including semi-automatic lattice averaging and frame registration, we have determined the substitutional sites of Mn atoms within the 1.2% Mn-doped Sb 2 Te 3 crystal. More importantly, the methodology developed in this study extends beyond Mn-doped Sb 2 Te 3 to other quantum materials, traditional semiconductors, and even electron irradiation sensitive materials.
Superconducting quantum bits (qubits) rely on ultra-thin, amorphous oxide tunneling barriers that can have significant inhomogeneities and defects as grown. This can result in relatively large uncertainties and deleterious effects in the circuits, limiting the scalability. Finding a robust solution to the junction reproducibility problem has been a long-standing goal in the field. Here, we demonstrate a transformational technique for controllably tuning the electrical properties of aluminum-oxide tunnel junctions. This is accomplished using a low-voltage, alternating-bias applied individually to the tunnel junctions, with which resistance tuning by more than 70% can be achieved. The data indicates an improvement of coherence and reduction of two-level system defects. Transmission electron microscopy shows that the treated junctions are predominantly amorphous, albeit with a more uniform distribution of alumina coordination across the barrier. This technique is expected to be useful for other devices based on ionic amorphous materials.
Not Available
Dy-free sintered magnets were fabricated by blending Neo powder with different grain boundary diffusion alloy powders. Cu, CeAl and CeAlCu have a negative effect on H cj of magnets, while PrAlCu and AlCuGa have a positive effect. The PrAlCu-added magnet achieves the best magnetic properties among all magnets with the additions of different diffusion alloys. With increasing PrAlCu from 0-10 wt.%, H cj of the magnets gradually increases from the original 14.5 kOe to 19.2 kOe. The magnet with 7.5 wt.% PrAlCu obtains a H cj of 18 kOe and (BH) max of 39.1 MGOe. It is found that Pr and Cu in PrAlCu alloy is mainly distributed at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced H cj . Here, the grain boundary engineering by adding an appropriate alloy is an effective method to improve H cj of Dy-free NdFeB magnets.
A new Co–Ni–N–C electrocatalyst for CO 2 reduction, featuring diatomic metal-nitrogen sites on N-doped carbon, has been developed. It shows high CO yield and faradaic efficiency, promising for various electrochemical reactions.
GaN/ZnGeN 2 /GaN double heterojunctions were grown by molecular beam epitaxy; we demonstrate coherent interfaces between ZnGeN 2 and GaN and highlight defects and associated properties of interest with respect to optoelectronic applications.
Not provided.
Niobium thin films on silicon substrate used in the fabrication of superconducting qubits have been characterized using scanning and transmission electron microscopy, electrical transport, magnetization, the London penetration depth - based quasiparticle spectroscopy, and real-space real-time magneto-optical imaging. Here we study niobium films to provide an example of a comprehensive analytical set that may benefit superconducting circuits such as those used in quantum computers. The films have a superconducting transition temperature of T c = 9.35 K and a fairly clean superconducting gap. The estimated superfluid density is enhanced at intermediate temperatures. These observations are consistent with the recent theory of anisotropic strong-coupling superconductivity in Nb and indicate outstanding quality. However, the response to the magnetic field is complicated, exhibiting significantly irreversible behavior and insufficient heat dissipation (to a substrate), leading to thermomagnetic instabilities. This may present a challenge for further improvement of transmon quantum coherence. Possible mitigation strategies are discussed.
Superconducting materials hold great potential for solid-state quantum computing. Their fabrication relies on established semiconductor fabrication techniques, such as thin film deposition and lithography, but the complex processing steps can result in defects at the qubits' interfaces and surfaces that can negatively impact coherence time. To improve superconducting qubit performance, it is essential to understand the structural features, at the atomic scale, that may act as sources of decoherence limiting factor in both the Josephson junction (JJ) and resonators, which are key components of superconducting qubit. This talk will present our recent studies on the microstructures in a 2D-transmon, with an emphasis on the JJ. For this research, a combination of advanced microscopy techniques, including high-resolution (S)TEM imaging, and spectroscopy (EDS and EELS) are used to identify possible coherence-limiting defects or structural features.
The challenge underlying superconducting quantum computing is to remove materials bottleneck for highly coherent quantum devices. The nonuniformity and complex structural components in the underlying quantum circuits often lead to local electric field concentration, charge scattering, dissipation and ultimately decoherence. Here we visualize interface dipole heterogeneous distribution of individual Al/AlO$_{x}$/Al junctions employed in transmon qubits by broadband terahertz scanning near-field microscopy that enables the non-destructive and contactless identification of defective boundaries in nano-junctions at an extremely precise nanoscale level. Our THz nano-imaging tool reveals an asymmetry across the junction in electromagnetic wave-junction coupling response that manifests as hot (high intensity) vs cold (low intensity) spots in the spatial electrical field structures and correlates with defected boundaries from the multi-angle deposition processes in Josephson junction fabrication inside qubit devices. The demonstrated local electromagnetic scattering method offers high sensitivity, allowing for reliable device defect detection in the pursuit of improved quantum circuit fabrication for ultimately optimizing coherence times.
Niobium is commonly used for superconducting quantum systems as readout resonators, capacitors, and interconnects. Structural defects at the Nb/Si and air/Nb interface may be a major source of two-level systems (TLS), which are detrimental to the device's coherence time. Thus, identifying and understanding the microscopic origin of possible TLS in Nb-based devices and their relationship to processing is key to superconducting qubit performance improvement. Here this work studied the structure and thermal stability of surface oxide on physical vapor deposited Nb films on Si wafers, using aberration-corrected (scanning) transmission electron microscopy and spectroscopy. Here, all Nb films exhibit columnar growth with strong [110] textures. After in-situ heating of the heterostructure at 360 °C inside the microscope, the initial amorphous niobium surface oxides decompose into face-centered cubic Nb nanograins in the amorphous Nb-O matrix, which may reduce microwave dissipation. Despite changes in the microstructure and chemistry of the niobium oxide surface layer due to heat treatment, the interface between the Nb and the surface oxide layer remains almost unchanged. Our comprehensive study of the Nb surface oxide decomposition mechanism may guide future superconducting qubit device optimization through interfacial scattering center and TLS minimization.
Abstract Magnetic defects play an important, but poorly understood, role in magnetic topological insulators (TIs). For example, topological surface transport and bulk magnetic properties are controlled by magnetic defects in Bi 2 Se 3 ‐based dilute ferromagnetic (FM) TIs and MnBi 2 Te 4 (MBT)‐based antiferromagnetic (AFM) TIs. Despite its nascent ferromagnetism, the inelastic neutron scattering data show that a fraction of the Mn defects in Sb 2 Te 3 form strong AFM dimer singlets within a quintuple block. The AFM superexchange coupling occurs via Mn–Te–Mn linear bonds and is identical to the AFM coupling between antisite defects and the FM Mn layer in MBT, establishing common interactions in the two materials classes. It is also found that the FM correlations in (Sb 1− x Mn x ) 2 Te 3 are likely driven by magnetic defects in adjacent quintuple blocks across the van der Waals gap. In addition to providing answers to long‐standing questions about the evolution of FM order in dilute TI, these results also show that the evolution of global magnetic order from AFM to FM in Sb‐substituted MBT is controlled by defect engineering of the intrablock and interblock coupling.
Abstract Increasing evidence indicates that angiogenesis plays a pivotal role in tumor progression. Formin‐like 2 (FMNL2) is well‐known for promoting metastasis; however, the molecular mechanisms by which FMNL2 promotes angiogenesis in colorectal cancer (CRC) remain unclear. Here, we found that FMNL2 promotes angiogenesis and metastasis of CRC in vitro and in vivo. The GDB/FH3 domain of FMNL2 directly interacts with epidermal growth factor‐like protein 6 (EGFL6). Formin‐like 2 promotes EGFL6 paracrine signaling by exosomes to regulate angiogenesis in CRC. Cytoskeleton associated protein 4 (CKAP4) is a downstream target of EGFL6 and is involved in CRC angiogenesis. Epidermal growth factor‐like protein 6 binds to the N‐terminus of CKAP4 to promote the migration of HUVECs by activating the ERK/MMP pathway. These findings suggest that FMNL2 promotes the migration of HUVECs and enhances angiogenesis and tumorigenesis in CRC by regulating the EGFL6/CKAP4/ERK axis. Therefore, the EGFL6/CKAP4/ERK axis could be a candidate therapeutic target for CRC treatment.
Abstract An experimental and numerical study of the plasma instabilities in an electrical exploding cylindrical Al liner is reported. The Al liner 3 mm in diameter and 10 μ m in thickness is exploded at the Qin-1 facility (450 ns, 400 kA). Various diagnostics, such as multi-frame laser shadowgraphy, an x-ray framing camera, and an x-ray backlighting system are developed. The different imaging systems are sensitive to plasma of different areal densities based on the comparison between the experiments and simulation, which reveal the dynamics of the exploding liner in more detail. The laser shadow images show the low-density plasma (∼1–2 × 10 −4 g cm −2 ) at the edge of the liner, and both the amplitude and wavelength of the plasma instabilities increase over time, which are considered to be magnetohydrodynamic (MHD) instabilities rather than electrothermal instabilities. During the ablation of the liner, quasi-periodic azimuthally correlated striations are directly observed in extreme ultraviolet (EUV) self-emission images. Meanwhile, the vertical filaments, which are electrothermal instabilities for plasma under the condition of ∂ η /∂ T < 0, are also observed in EUV self-emission images. The x-ray backlighting images of the exploding liner are obtained by placing an X -pinch load on the current-return path to serve as an x-ray point source (∼1 ns, ∼10 μ m). The x-ray backlighting results show the behavior of the high-density plasma (∼1.89 × 10 −3 g cm −2 ), which includes the transition from electrothermal to MHD instabilities. Finally, we realized a 2D MHD simulation of the exploding liner under experimental conditions, which shows good agreement with the results of the experimental perturbation.