Search NASA⌕ Search

Engineering topics

Zhu, C.

Publications and source records attributed to Zhu, C..

At least 19 records

FES 2023 Theory & Simulation Performance Target

The Report for the 2023 Theory & Simulation Performance Target (TSPT) is presented herein. The 1st, 2nd and 3rd Quarter Reports are given in Sec. I, Sec. II and Sec. III. These are unchanged from those previously submitted, except that in this final document the equations, figures and citations have been automatically renumbered. The 4th Quarter Report is given in Sec. IV. The following material presents verification calculations of several widely used three-dimensional (3D) magnetohydrodynamic (MHD) equilibrium codes in strongly shaped configurations; for both fixed and free-boundary equilibria; for the so-called vacuum case and for the case of high plasma pressure; and, for magnetic fields that have nested magnetic surfaces and for fields that have a magnetic island. The configurations studied includes the recently discovered “precise-QA” case [Phys. Rev. Lett., 128, 035001 (2002)] and other highly optimized configurations. Because of the strong (extreme) shaping, the latter of these pose challenges to the 3D MHD codes. A new method is introduced for constructing coordinates in arbitrarily shaped toroidal domains, and this can improve the robustness of 3D equilibrium calculations. Beyond the equilibrium calculation, this report demonstrates the capability of performing non-linear extended-MHD modelling of optimized stellarator equilibria. This capability allows the assessment not only of linear stability thresholds but also of the nonlinear evolution of unstable equilibria to new configurations that might be far from the original configuration, with significantly different transport properties and magnetic topology. They also enable the self-consistent determination of pressure profiles in non-integrable magnetic topology through the use of highly anisotropic thermal-transport equations. The calculations presented here represent the first demonstration of extended-MHD calculations in strongly-shaped, optimized quasi-symmetric configurations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A novel scheme for error field correction in permanent magnet stellarators

Stellarators offer a promising path towards fusion reactors, but their design and construction are complicated by stringent tolerance requirements on highly complex 3D coils. A potential way to simplify the engineering requirements for stellarators is to use simple planar toroidal field coils along with permanent magnet arrays to generate shaping fields. In order to ensure sufficient field accuracy while minimizing engineering complexity and system cost, new techniques are required to correct the field produced by the permanent magnet arrays to within requirements set by plasma physics. This work describes a novel correction method developed for this purpose. This analysis is applied to the design of a quasi-axisymmetric stellarator that employs a combination of permanent magnets and planar toroidal field coils to generate its magnetic field. Analysis techniques and initial results using the method for error correction on a proposed permanent magnet stellarator are shown, and it is demonstrated that the method successfully meets the design requirements of the project.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Improving the stellarator through advances in plasma theory

Improvements to the stellarator concept can be realized through advancements in theoretical and computational plasma physics. Herein, recent advances are reported in the topical areas of: (1) improved energetic ion confinement, (2) the impact of three-dimensional (3D) shaping on turbulent transport, (3) reducing coil complexity, (4) novel optimization and design methods, and (5) computational magnetohydrodynamic tools. Furthermore, these advances enable the development of new stellarator configurations with improved confinement properties.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

3D printed Ni-Mn-Fe Bi-Functional Catalyst for Metal Air Batteries

Oxygen evolution catalyst with porous structures on the submillimeter and millimeter ranges have been shown to have high catalytic activity. Often, a limiting factor in the performance of a catalyst can be its specific surface area as this can limit the availability of active sites which encourage the desired reaction. As such, the inclusion of a hierarchical structure that include both meso-scale and nano-scale porosity can offer a means to greatly increase the performance of electrochemical catalysts. We have developed a method for manufacturing samples with such a hierarchical structure by combining techniques of direct ink writing (DIW), thermal sintering and free corrosion based dealloying. This allows us to prepare three-dimensionally structured samples with open-cell porosity at the macro-, micro- and nano-scales. Each level of porosity offers a different advantage to the overall functionality and applicability of this technology.

25 ENERGY STORAGE↗

Computation of the Biot–Savart line integral with higher-order convergence using straight segments

One common approach to computing the magnetic field produced by a filamentary current-carrying coil is to approximate the coil as a series of straight segments. The Biot–Savart field from each straight segment is analytically known. However, if the endpoints of the straight segments are chosen to lie on the coil, then the accuracy of the Biot–Savart computation is generally only the second order in the number of endpoints. In this work, we propose a simple modification: shift each end point of the coil in the outward normal direction by an amount proportional to the local curvature. With this modification, the Biot–Savart accuracy increases to the fourth order and the numerical error is dramatically reduced for a given number of discretization points.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Physics basis for design of 3D coils in tokamaks

Recent progress in 3D tokamak modeling is now leveraged to create a conceptual design of new external 3D field coils for the DIII-D tokamak. In this work generalized perturbed equilibrium code is used to determine optimally efficient spectrum for driving total, core, and edge neoclassical toroidal viscosity torque. These fundamental modes of 3D control are shown to have consistent outboard structures across a wide variety of plasma scenarios and machines. Given these target spectra, the currents and 3D geometry of multiple coils can be optimized to increase efficient drive for the physics of interest without undesired secondary effects. Here, this nonlinear optimization is demonstrated using the flexible optimized coils using space-curves code. The optimized coils are individually distorted in space, creating toroidal 'arrays' containing a variety of shapes that often wrap around a significant poloidal extent of the machine. Importantly, efficient coupling can be maintained even when enforcing large distances between coils and the plasma during the geometric optimization of coil designs. Finally, the physics-driven optimization presented here thus provides a practical path to utilizing coils built on the exterior of the vacuum chamber in future reactors to obtain the powerful 3D field benefits demonstrated on current machines with close, internal coils.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Quasisymmetric Optimization of Nonaxisymmetry in Tokamaks

Predictive 3D optimization reveals a novel approach to modify a nonaxisymmetric magnetic perturbation to be entirely harmless for tokamaks, by essentially restoring quasisymmetry in perturbed particle orbits as much as possible. Such a quasisymmetric magnetic perturbation (QSMP) has been designed and successfully tested in the KSTAR and DIII-D tokamaks, demonstrating no performance degradation despite the large overall amplitudes of nonaxisymmetric fields and strong response otherwise expected in the tested plasmas. The results indicate that a quasisymmetric optimization is a robust path of error field correction across the resonant and nonresonant field spectrum in a tokamak, leveraging the prevailing concept of quasisymmetry for general 3D plasma confinement systems such as stellarators. Finally, the optimization becomes, in fact, a simple eigenvalue problem to the so-called torque response matrices if a perturbed equilibrium is calculated consistent with nonaxisymmetric neoclassical transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Constrained stellarator coil curvature optimization with FOCUS

Finding less complicated coils that have adequately low field errors is a crucial step in stellarator development. One coil metric that is of high importance is the maximum curvature of the coil centreline, or coil single filament. Conductors cannot be bent below some threshold minimum radius of curvature. High coil curvatures can cause strains to exceed acceptable levels, especially in superconducting coils. We investigate three ways to optimize coil curvature and find that applying penalty functions to the coil curvature solves for coils that have a constrained maximum curvature and low field error. Penalty functions are implemented in FOCUS and coil solutions optimized for an HSX-like ‘plasma boundary’ are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The interplay between spatial and heliconical orientational order in twist-bend nematic materials

The helical pitch formed by organic molecules, such as the α-helix of proteins, usually requires hydrogen bonding between chiral units and long-range positional order. It was recently found that certain liquid crystal oligomers can have a twist-bend nematic (NTB) phase with nanoscale heliconical structure without hydrogen bonding, molecular chirality or positional order. To understand the nature of this unique structure, here we present hard and resonant tender X-ray scattering studies of two novel sulfur containing dimer materials. We simultaneously measure the temperature dependences of the helical pitch and the correlation length of both the helical and positional order. In addition to an unexpected strong variation of the pitch with the length of the spacer connecting the monomer units, we find that at the transition to the NTB phase the positional correlation length drops. Additionally, the helical structure was found not only in the NTB phase but observed even in the upper range of a smectic phase that forms just below the NTB state. The coexistence of smectic layering and the heliconical order indicates a layered (SmATB) phase wherein the rigid units of the dimers are tilted with respect to the smectic layer normal in order to accommodate the bent conformation of the dimers and the tilt direction rotates along the heliconical axis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Optimized finite-build stellarator coils using automatic differentiation

A new stellarator coil design code is introduced that optimizes the position and winding pack orientation of finite-build coils. The new code, called flexible optimized curves in space using automatic differentiation (AD) and finite build (FOCUSADD), performs gradient-based optimization in a high-dimensional, non-convex space. The derivatives with respect to parameters of finite-build coils are easily and efficiently computed using AD. FOCUSADD parametrizes coil positions in free space using a Fourier series and uses a multi-filament approximation to the coil winding pack. The orientation of the winding pack is parametrized with a Fourier series and can be optimized as well. Optimized finite-build coils for a Wendelstein 7-X (W7-X)-like stellarator are found, and compared with filamentary coil results. The final positions of optimized finite-build W7-X-like coils are shifted, on average, by approximately 2.5 mm relative to optimized filamentary coils. These results suggest that finite-build effects should be accounted for in the optimization of stellarators with low coil tolerances.

43 PARTICLE ACCELERATORS↗

Geometric concepts for stellarator permanent magnet arrays

The development of stellarators that use permanent magnet arrays to shape their confining magnetic fields has been a topic of recent interest, but the requirements for how such magnets must be shaped, manufactured, and assembled remain to be determined. To address these open questions, we have performed a study of geometric concepts for magnet arrays with the aid of the newly developed MAGPIE code. A proposed experiment similar to the National Compact Stellarator Experiment (NCSX) is used as a test case. Here, two classes of magnet geometry are explored: curved bricks that conform to a regular grid in cylindrical coordinates, and hexahedra that conform to the toroidal plasma geometry. In addition, we test constraints on the magnet polarization. While magnet configurations constrained to be polarized normally to a toroidal surface around the plasma are unable to meet the required magnetic field parameters when subject to physical limitations on the strength of present-day magnets, configurations with unconstrained polarizations are shown to satisfy the physics requirements for a targeted plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Localizing resonant magnetic perturbations for edge localized mode control in KSTAR

An external 3D magnetic perturbation typically drives a resonant response at the rational surfaces from the core to the edge of tokamak plasmas, due to strong mode coupling and amplification. In this paper, we present a method to isolate the edge from core resonant fields using the ideal perturbed equilibrium code and to design an edge-localized resonant magnetic perturbation (RMP) for effective edge localized mode (ELM) control. A robust feature of the edge-localized RMP is the curtailed response to the field at the low-field-side (LFS) midplane, as opposed to typical RMPs which strongly resonate with the LFS fields. This emphasizes the importance of off-midplane coils to improve ELM control without provoking a large core response that could lead to devastating instabilities. The conceptual design of new ELM control coils based on the edge-localized RMP in KSTAR shows how this new insight can be utilized to enhance the efficiency of our ELM suppression capabilities. Simple window-pane coils matching the edge-localized resonant mode structure substantially expand in the ELM suppression window beyond the existing coil. Further optimization using the flexible optimized coils using space-curves code leads to additional enhancement in the edge-localized control.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Free-boundary MRxMHD equilibrium calculations using the stepped-pressure equilibrium code

Here the stepped-pressure equilibrium code (SPEC) (Hudson et al 2012 Phys. Plasmas 19 , 112 502) is extended to enable free-boundary multi-region relaxed magnetohydrodynamic (MRxMHD) equilibrium calculations. The vacuum field surrounding the plasma inside an arbitrary 'computational boundary', , is computed, and the virtual-casing principle is used iteratively to compute the normal field on so that the equilibrium is consistent with an externally produced magnetic field. Recent modifications to SPEC are described, such as the use of Chebyshev polynomials to describe the radial dependence of the magnetic vector potential, and a variety of free-boundary verification calculations are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Replication Data for: Toward digitally controlled catalyst architectures: Hierarchical nanoporous gold via 3D printing

The data underlying this published work have been made publicly available in this repository as part of the IMASC Data Management Plan. This work was supported as part of the Integrated Mesoscale Architectures for Sustainable Catalysis (IMASC), an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences under Award # DE-SC0012573.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗