Final Scientific-Technical Report-DE-SC0024061
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Zhu, Chunxiang.
Explore the source record for details and available documents.
Not Available
Converting CO 2 to value-added chemicals, e. g., CH 3 OH, is highly desirable in terms of the carbon cycling while reducing CO 2 emission from fossil fuel combustion. Cu-based nanocatalysts are among the most efficient for selective CO 2 -to-CH 3 OH transformation; this conversion, however, suffers from low reactivity especially in the thermodynamically favored low temperature range. We herein report ultrasmall copper (Cu) nanocatalysts supported on crystalline, mesoporous zinc oxide nanoplate (Cu@mZnO) with notable activity and selectivity of CO 2 -to-CH 3 OH in the low temperature range of 200–250 °C. Cu@mZnO nanoplates are prepared based on the crystal-crystal transition of mixed Cu and Zn basic carbonates to mesoporous metal oxides and subsequent hydrogen reduction. Under the nanoconfinement of mesopores in crystalline ZnO frameworks, ultrasmall Cu nanoparticles with an average diameter of 2.5 nm are produced. Cu@mZnO catalysts have a peak CH 3 OH formation rate of 1.13 mol h −1 per 1 kg under ambient pressure at 246 °C, about 25 °C lower as compared to that of the benchmark catalyst of Cu−Zn−Al oxides. In conclusion, our new synthetic strategy sheds some valuable insights into the design of porous catalysts for the important conversion of CO 2 -to-CH 3 OH.
Despite much technical progress achieved so far, the exact surface and shape evolution during wet chemical etching is less unraveled, especially in ionically bonded ceramics. Herein, by using in situ liquid cell transmission electron microscopy, a repeated two-stage anisotropic and pulsating periodic etching dynamic is discovered during the pencil shape evolution of a single crystal ZnO nanorod in aqueous hydrochloric acid. Specifically, the nanopencil tip shrinks at a slower rate along [0001̅] than that along the $\langle$101̅0$\rangle$ directions, resulting in a sharper ZnO pencil tip. Afterward, rapid tip dissolution happens due to accelerated etching rates along various crystal directions. Concurrently, the vicinal base region of the original nanopencil tip emerges as a new tip followed by the repeated sequence of tip shrinking and removal. The high-index surfaces, such as {101̅m} (m = 0, 1, 2, or 3) and {21̅1̅n} (n = 0, 1, 2, or 3), are found to preferentially expose in different ratios. Our 3D electron tomography, convergent beam electron diffraction, middle-angle bright-field STEM, and XPS results indicate the dissociative Cl – species were bound to the Zn-terminated tip surfaces. Furthermore, DFT calculation suggests the preferential Cl – passivation over the {101̅1} and (0001) surfaces of lower energy than others, leading to preferential surface exposures and the oscillatory variation of different facet etching rates. The boosted reactivity due to high-index nanoscale surface exposures is confirmed by comparatively enhanced chemical sensing and CO 2 hydrogenation activity. In conclusion, these findings provide an in-depth understanding of anisotropic wet chemical etching of ionic nanocrystals and offer a design strategy for advanced functional materials.
Cu-ZnO-Al 2 O 3 is the most widely applied catalyst for CO 2 hydrogenation to methanol. However, it is still a challenge to produce methanol using this catalyst under low-temperature (<250 °C) and low-pressure (<10 bar) conditions with desirable yield and selectivity. In this work, by tuning the experimental processing parameters such as solvent, loading amount, and annealing temperature, highly improved ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalysts have been successfully demonstrated. Here, by using organic solvent (N,N-dimethylformamide (DMF), acetone, or isopropanol) for dip-coating loading process instead of deionized (DI) water, Cu-ZnO-Al 2 O 3 nanocatalysts was comparatively better dispersed on the nanorod array support with populated and abundant active sites, thus enhancing the methanol yield. With the control of the loading amount and annealing temperature, finely distributed Cu nanoparticles were obtained on the ZnO nanorod surfaces to enhance the interactions between Cu and ZnO nanorod surfaces. Further improvement of the catalyst performance is demonstrated by tuning the reaction space velocity. At 200 °C and 10 bar conditions, the optimized catalyst achieved a methanol yield of 6.46 mol h –1 kg –1 with 100 % selectivity. The good stability after prolonged testing of the catalysts demonstrates the potential practical implementation. The in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) measurements under the 1 bar reveal that the CO 2 hydrogenation to methanol on the ZnO nanoarray supported Cu-ZnO-Al 2 O 3 catalyst follows the CO reaction pathway, due to the surface oxygen vacancies on ZnO nanorods which facilitate CO 2 dissociation.
TiO 2 supported catalysts have been widely studied for the selective catalytic reduction (SCR) of NO x ; however, comprehensive understanding of synergistic interactions in multi-component SCR catalysts is still lacking. For this work, transition metal elements (V, Cr, Mn, Fe, Co, Ni, Cu, La, and Ce) were loaded onto TiO 2 nanoarrays via ion-exchange using protonated titanate precursors. Amongst these catalysts, Mn-doped catalysts outperform the others with satisfactory NO conversion and N 2 selectivity. Cu co-doping into the Mn-based catalysts promotes their low-temperature activity by improving reducibility, enhancing surface Mn 4+ species and chemisorbed labile oxygen, and elevating the adsorption capacity of NH 3 and NO x species. While Ce co-doping with Mn prohibits the surface adsorption and formation of NH 3 and NO x derived species, it boosts the N 2 selectivity at high temperatures. By combining Cu and Ce as doping elements in the Mn-based catalysts, both the low-temperature activity and the high-temperature N 2 selectivity are enhanced, and the Langmuir–Hinshelwood reaction mechanism was proved to dominate in the trimetallic Cu–Ce–5Mn/TiO 2 catalysts due to the low energy barrier.
Defect engineering through elemental doping is an efficient way to boost the performance of semiconductor photocatalysts. For this work, transition-metal (TM) doped titanate nanowires (TNWs) were prepared via ion-exchange over the titanate precursors and demonstrated for the Rhodamine B (RhB) degradation under ultraviolet (UV) light irradiation. The ion-exchange of selective ions (V 5+ , Cr 3+ , Ni 2+ , and Zn 2+ ) with protons from pristine TNWs resulted in the hierarchical meso-porosity of nanowires with large pores of ~5–20 nm by TM doping and small pores of ~3.6–4.5 nm inherited from pristine TNWs, which facilitates the mass transfer while maintaining high surface area and active sites. Meanwhile, the TM intercalation partially reduces the Ti 4+ to Ti 3+ and narrows the optical bandgap, which, together with oxygen vacancies and superoxide radicals from pristine TNWs, enhance the adsorption and photocatalytic degradation performance of RhB. This work helps to elucidate the effects of transition-metal doping and provides a rational strategy towards high performance titanate-based photocatalysts for efficient and sustainable wastewater treatment.
Explore the source record for details and available documents.
Two-dimensional (2D) materials have recently attracted wide attention and rapidly established themselves in various applications. In particular, 2D materials are regarded as promising building blocks for gas sensors due to their high surface-to-volume ratio, ease in miniaturization, and flexibility in enabling wearable electronics. Compared with other 2D materials, MoS{sub 2} is particularly intriguing because it has been widely researched and exhibits semiconducting behavior. Here, we have fabricated MoS{sub 2} resistor based O{sub 2} sensors with a back gate configuration on a 285 nm SiO{sub 2}/Si substrate. The effects of applying back gate voltage stress on O{sub 2} sensing performance have been systematically investigated. With a positive gate voltage stress, the sensor response improves and the response is improved to 29.2% at O{sub 2} partial pressure of 9.9 × 10{sup −5} millibars with a +40 V back-gate bias compared to 21.2% at O{sub 2} partial pressure of 1.4 × 10{sup −4} millibars without back-gate bias; while under a negative gate voltage stress of −40 V, a fast and full recovery can be achieved at room temperature. In addition, a method in determining O{sub 2} partial pressure with a detectability as low as 6.7 × 10{sup −7} millibars at a constant vacuum pressure is presented and its potential as a vacuum gauge is briefly discussed.