Search NASA⌕ Search

Engineering topics

Zimcik, D. G.

Publications and source records attributed to Zimcik, D. G..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Buffet Load Alleviation

High performance aircraft are, by their very nature, often required to undergo maneuvers involving high angles of attack. Under these conditions unsteady vortices emanating from the wing and the fuselage will impinge on the twin fins (required for directional stability) causing excessive buffet loads, in some circumstances, to be applied to the aircraft. These loads result in oscillatory stresses, which may cause significant amounts of fatigue damage. Active control is a possible solution to this important problem. A full-scale test was carried out on an F/A-18 fuselage and fins using piezoceramic actuators to control the vibrations. Buffet loads were simulated using very powerful electromagnetic shakers. The first phase of this test was concerned with the open loop system identification whereas the second stage involved implementing linear time invariant control laws. This paper looks at some of the problems encountered as well as the corresponding solutions and some results. It is expected that flight trials of a similar control system to alleviate buffet will occur as early as 2001.

Ryall, T. G.↗
NASA NTRS1999

Control Law Synthesis for Vertical Fin Buffeting Alleviation Using Strain Actuation

In the present investigation, the results obtained during the ground test of a closed-loop control system conducted on a full-scale fighter to attenuate vertical fin buffeting response using strain actuation are presented. Two groups of actuators consisting of piezoelectric elements distributed over the structure were designed to achieve authority over the first and second modes of the vertical fin. The control laws were synthesized using the Linear Quadratic Gaussian (LQG) method for a time-invariant control system. Three different pairs of sensors including strain gauges and accelerometers at different locations were used to close the feedback loop. The results demonstrated that measurable reductions in the root-mean-square (RMS) values of the fin dynamic response identified by the strain transducer at the critical point for fatigue at the root were achieved under the most severe buffet condition. For less severe buffet conditions, reductions of up to 58% were achieved.

Nitzsche, F.↗
NASA NTRS1995

Space environmental effects on polymer matrix composites as a function of sample location on LDEF

This paper presents results on the effect of circumferential location on the variation in solar absorptance (alpha(sub S)) and infrared emittance (epsilon) for five different polymer matrix composites (PMC), and variations in erosion depth due to atomic oxygen (AO) for fourteen different PMC materials. In addition, a chemical content design parameter (gamma) has been found that correlates well with the erosion yield obtained from space flight data and hyperthermal AO tests for hydrocarbon polymeric materials. This parameter defines the ratio of the total number of atoms in a repeat monomer unit to the difference between the total carbon content and the total number of intermolecular oxygen atoms in the same repeat unit.

Tennyson, R. C.↗
NASA NTRS1992

Proposed test program and data base for LDEF polymer matrix composites

A survey of the polymer matrix composite materials that were flown on Long Duration Exposure Facility (LDEF) is presented with particular attention to the effect of circumferential location (alpha) on the measured degradation and property changes. Specifically, it is known that atomic oxygen fluence (AO), VUV radiation dose, and number of impacts by micrometeoroids/debris vary with alpha. Thus, it is possible to assess material degradation and property damage changes with alpha for those materials that are common to three or more locations. Once the alpha-dependence functions were defined, other material samples will provide data that can readily be used to predict damage and property changes as a function of alpha as well. What data can be realistically obtained from these materials, how this data can be obtained, and the scientific/design value of the data to the user community is summarized. Finally, a proposed test plan is presented with recommended characterization methodologies that should be employed by all investigators to ensure consistency in the data base that will result from this exercise.

Tennyson, R. C.↗
NASA NTRS1987

Effect of long-term exposure to Low Earth Orbit (LEO) space environment

Data obtained from components and materials from the Solar Maximum Mission satellite are presented and compared to data for similar materials obtained from the Advanced Composite Materials Exposure to Space Experiment (ACOMEX) flown on Shuttle mission STS-41G. In addition to evaluation of surface erosion and mass loss that may be of importance to very long-term missions, comparisons of solar absorptance and thermal emittance measurements for both long and short term exposures were made. Although the ratio of absorptance over emittance can be altered by proper choice of materials to ensure a proper operating environment for the spacecraft, once the thermal design is established, it is important that the material properties not change in order to maintain the operating environment for many payload and bus items such as electronics, batteries, fuel, etc. However, data presented show significant changes after short exposure in low Earth environment. Moreover, the measured changes are shown to differ according to the manner of exposure, i.e., normal or oblique, which also affects the resultant eroded surface morphology. These results identify constraints to be considered in development of flight experiments or laboratory testing.

Zimcik, D. G.↗
NASA NTRS1985

The effect of Low Earth Orbit space environment on polymeric spacecraft materials

The Advanced Composite Materials Exposure to Space Experiment flown on shuttle mission STS-41G was designed to investigate the effect of low Earth orbit space environment on polymeric spacecraft materials. The effect of the phenomenon attributed to atomic oxygen on Kapton and advanced composite materials of carbon-epoxy and kevlar epoxy is described. The results of true space exposure are compared to duplicate specimens subjected to a simulated environment in an Earth-based nozzle beam test facility utilizing microwave discharge to form atomic oxygen. Although the energy level for atomic oxygen in the beam facility did not achieve the orbital energy level of 5 eV, similar effects of surface erosion and degradation are observed after equivalent exposure times.

Zimcik, D. G.↗
NASA NTRS1985

Results of apparent atomic oxygen reactions with spacecraft materials during shuttle flight STS-41G

The effect of atomic oxygen interaction experienced by polymeric-based spacecraft materials is described. An experimental package (ACOMEX) flown on shuttle mission STS-41G carried out the investigation of advanced composite specimens such as carbon-epoxy and Kevlar-epoxy both with and without protective coatings added to thermal protective paints and films. Information on the exposure environment of the specimens was provided by a carbon coated atomic oxygen fluence monitor together with a photographic record. Mass loss measurements and photomicrographs made possible the analysis of the effect of interaction. After a total of about 38 hours of equivalent normal exposure at 225 km altitude the results showed that unprotected exposed surfaces exhibited severe erosion and mass loss with the possibility of seriously degrading structural and thermal performance. However, the specimens with a thin fluorocarbon overcoat showed promise of providing a protective barrier to the attack without altering the base properties of the material.

Zimcik, D. G.↗
NASA NTRS1984

Flight test of a synthetic aperture radar antenna using STEP

To establish confidence in its overall performance, credible information on the synthetic aperture radar antenna's mechanical properties in orbit must be obtained. However, the antenna's size, design, and operating environment make it difficult to simulate operating conditions under 1-g Earth conditions. The Space Technology Experiments Platform (STEP) offers a timely opportunity to mechanically qualify and characterize the antenna design in a representative environment. The proposed experimental configuration would employ a half-system of the full-scale RADARSAT antenna which would be mounted on the STEP platform in the orbiter cargo bay such that it could be deployed and retracted in orbit (as shown in this figure). The antenna would be subjected to typical environmental exposures while an array of targets and sensors on the antenna support structure and reflecting surface are observed and monitored. In particular, the typical environments would include deployment and retraction, dynamic response to vehicle thruster or base exciter inputs, and thermal soak and transient effects upon entering or exiting Earth eclipse. The proposed experiment would also provide generic information on the properties of large space structures in space and on techniques to obtain the desired information.

Zimcik, D. G.↗
NASA NTRS1984

An atomic oxygen facility for studying polymer materials for spacecraft applications

A nozzle beam facility utilizing microwave discharge on a helium carrier gas seeded with oxygen to produce atomic oxygen fluxes of the order of 10 to the 15th power atoms/cu cm/sec is described. In addition, limited test results obtained from exposing a graphite/epoxy composite and Kapton (H) film are presented in terms of mass loss measurements and changes in surface morphology.

Tennyson, R. C.↗