Engineering topics

Zimmerman, F. R.

Publications and source records attributed to Zimmerman, F. R..

6 records

NASA NTRS2005

Welding in Space: Lessons Learned for Future In Space Repair Development

Welds have been made in the harsh environment of space only twice in the history of manned space flight. The United States conducted the M5 12 experiment on Skylab and the former Soviet Union conducted an Extravehicular Activity. Both experiments demonstrated electron beam welding. A third attempt to demonstrate and advance space welding was made by the Marshall Space Flight Center in the 90's but the experiment was demanifested as a Space Shuttle payload. This presentation summarizes the lessons learned from these three historical experiences in the areas of safety, design, operations and implementation so that welding in space can become an option for in space repair applications.

Russell, C. K.↗

NASA NTRS1999

Low-Pressure Gas Effects on the Potency of an Electron Beam Against Ceramic Cloth

An 8-kv electron beam with a current in the neighborhood of 100 mA from the Ukrainian space welding "Universal Hand Tool" (UHT) burned holes in Nextel AF-62 ceramic cloth designed to withstand temperatures up to 1,427 C. The burnthrough time was on the order of 8 scc at standoff distances between UHT and cloth ranging from 6-24 in. At both closer (2 in.) and farther (48 in.) standoff distances the potency of the beam against the cloth declined and the burnthrough time went up significantly. Prior to the test it had been expected that the beam would lay down a static charge on the cloth and be deflected without damaging the cloth. The burnthrough is thought to be an effect of partial transmission of beam power by a stream of positive ions generated by the high-voltage electron beam from contaminant gas in the "vacuum" chamber. A rough quantitative theoretical computation appears to substantiate this possibility.

Nunes, A. C., Jr.↗

NASA NTRS1999

How an Electron Beam (Eventually) Penetrates Ceramic Cloth

In anticipation of the International Space Welding Experiment (ISWE) the effect of an electron beam was investigated on Nextel AF-62 ceramic cloth designed to withstand temperatures up to 1427 C. It was anticipated that the cloth would take a static charge that would repel the beam and remain undamaged. It was found that after some seconds the impinging beam penetrated penetrated the cloth. Further, the penetration time went up significantly both at longer and at closer standoff distances. A tentative explanation appears to fit the observed facts. The electrons in the beam generate positive ions by collisions with the contaminant gas molecules in the vacuum chamber. The positive ions transfer a small but significant fraction of the beam power to the cloth. Under the impingement of the positive ions the cloth heats up until sufficient outgassing occurs to initiate arcing. Once arcing occurs the full beam power impinges on the cloth and, almost instantaneously, burns a hole.

Nunes, A. C., Jr.↗

NASA NTRS1995

Replacement of corrosion protection chromate primers and paints used in cryogenic applications on the Space Shuttle with wire arc sprayed aluminum coatings

With the advent of new environmental laws restricting volatile organic compounds and hexavalent chrome emissions, 'environmentally safe' thermal spray coatings are being developed to replace the traditional corrosion protection chromate primers. A wire arc sprayed aluminum coating is being developed for corrosion protection of low pressure liquid hydrogen carrying ducts on the Space Shuttle Main Engine. Currently, this hardware utilizes a chromate primer to provide protection against corrosion pitting and stress corrosion cracking induced by the cryogenic operating environment. The wire are sprayed aluminum coating has been found to have good potential to provide corrosion protection for flight hardware in cryogenic applications. The coating development, adhesion test, corrosion test and cryogenic flexibility test results will be presented.

Daniel, R. L.↗

NASA NTRS1992

Vacuum plasma spray applications on liquid fuel rocket engines

The vacuum plasma spray process (VPS) has been developed by NASA and Rocketdyne for a variety of applications on liquid fuel rocket engines, including the Space Shuttle Main Engine. These applications encompass thermal barrier coatings which are thermal shock resistant for turbopump blades and nozzles; bond coatings for cryogenic titanium components; wear resistant coatings and materials; high conductivity copper, NaRloy-Z, combustion chamber liners, and structural nickel base material, Inconel 718, for nozzle and combustion chamber support jackets.

Mckechnie, T. N.↗

NASA NTRS1992

Metallurgy and properties of plasma spray formed materials

Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

Mckechnie, T. N.↗