Search NASA⌕ Search

Engineering topics

Zinkle, Steven J

Publications and source records attributed to Zinkle, Steven J.

At least 19 records

Evaluation of high strength, high conductivity CuNiBe alloys for fusion energy applications

The unirradiated tensile properties for several different heats and thermomechanical treatment conditions of precipitation strengthened Hycon 3HPTM CuNiBe (Cu-2%Ni-0.35%Be in wt.%) have been measured over the temperature range of 20-500 C for longitudinal and long transverse orientations. The room temperature electrical conductivity has also been measured for several heats, and the precipitate microstructure was characterized using transmission electron microscopy. The CuNiBe alloys exhibit very good combination of strength and conductivity at room temperature, with yield strengths of 630-725 MPa and electrical conductivities of 65-72% International Annealed Copper Standard (IACS). The strength remained relatively high at all test temperatures, with yield strengths of 420-520 MPa at 500 C. However, low levels of ductility (<5% uniform elongation) were observed at test temperatures above 200-250 C, due to flow localization near grain boundaries (exacerbated by having only 10-20 grains across the gage thickness of the miniaturized sheet tensile specimens). Scanning electron microscopy observation of the fracture surfaces found a transition from ductile transgranular to ductile intergranular fracture with increasing test temperature. Fission neutron irradiation to a dose of ~0.7 displacements per atom (dpa) at temperatures between 100 and 240 C produced a slight increase in strength and a significant decrease in ductility. The measured tensile elongation increased with increasing irradiation temperature, with a uniform elongation of ~3.3% observed at 240 C. The electrical conductivity decreased slightly following irradiation, due to the presence of defect clusters and Ni, Zn, Co transmutation products. Considering also previously published fracture toughness data, this indicates that CuNiBe alloys have irradiated tensile and electrical properties comparable or superior to CuCrZr and oxide dispersion strengthened copper at temperatures <250 C, and may be an attractive candidate for certain fusion energy structural applications. Conversely, CuNiBe may not be preferred at intermediate temperatures of 250-500 C due to the poor ductility and fracture toughness of CuNiBe alloys at temperatures >250 C. The potential deformation mechanisms responsible for the transition from transgranular to intergranular fracture are discussed. The possible implications for other precipitation hardened alloys such as nickel based superalloys are briefly discussed.

Zinkle, Steven J↗

EFFECTS OF ION IRRADIATION ON Zr52.5Cu17.9Ni14.6Al10Ti5 (BAM-11) BULK METALLIC GLASS

Bulk metallic glasses are intriguing candidates for nuclear applications due to their inherent amorphous structure, but their radiation response is largely unknown due to the relatively recent nature of innovations in bulk metallic glass fabrication. Here, microstructural and mechanical property evaluations have been performed on a Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass (BAM-11) irradiated with 3 MeV Ni+ ions to 0.1 and 1.0 dpa at room temperature and 200 C. Nanoindentation hardness and Young s modulus both decreased by 6 to 20% in samples irradiated at room temperature, with the sample irradiated to 1.0 dpa experiencing the greatest change in mechanical properties. However, no significant changes in properties were observed in the samples irradiated at 200 C, and transmission electron microscopy showed no visible evidence of radiation damage or crystallization following ion irradiation at any of the tested conditions. These results suggest that BAM-11 bulk metallic glass may be useful for certain applications in nuclear environments.

Perez-Bergquist, Alex G↗

Designing Radiation Resistance in Materials for Fusion Energy

Proposed fusion and advanced (Generation IV) fission energy systems require high performance materials capable of satisfactory operation up to neutron damage levels approaching 200 atomic displacements per atom with large amounts of transmutant hydrogen and helium isotopes. After a brief overview of fusion reactor concepts and radiation effects phenomena in structural and functional (non-structural) materials, three fundamental options for designing radiation resistance are outlined: Utilize matrix phases with inherent radiation tolerance, select materials where vacancies are immobile at the design operating temperatures, or construct high densities of point defect recombination sinks. Environmental and safety considerations impose several additional restrictions on potential materials systems, but reduced activation ferritic/martensitic steels (including thermomechanically treated and oxide dispersion strengthened options) and silicon carbide ceramic composites emerge as robust structural materials options. Materials modeling (including computational thermodynamics) and advanced manufacturing methods are poised to exert a major impact in the next ten years.

Zinkle, Steven J↗

Materials Challenges in Nuclear Energy

Nuclear power currently provides about 13% of the worldwide electrical power, and has emerged as a reliable baseload source of electricity. A number of materials challenges must be successfully resolved for nuclear energy to continue to make further improvements in reliability, safety and economics. The operating environment for materials in current and proposed future nuclear energy systems is summarized, along with a description of materials used for the main operating components. Materials challenges associated with power uprates and extensions of the operating lifetimes of reactors are described. The three major materials challenges for the current and next generation of water-cooled fission reactors are centered on two structural materials aging degradation issues (corrosion and stress corrosion cracking of structural materials and neutron-induced embrittlement of reactor pressure vessels), along with improved fuel system reliability and accident tolerance issues. The major corrosion and stress corrosion cracking degradation mechanisms for light water reactors are reviewed. The materials degradation issues for the Zr alloy clad UO2 fuel system currently utilized in the majority of commercial nuclear power plants is discussed for normal and off-normal operating conditions. Looking to proposed future (Generation IV) fission and fusion energy systems, there are 5 key bulk radiation degradation effects (low temperature radiation hardening and embrittlement, radiation-induced and modified solute segregation and phase stability, irradiation creep, void swelling, and high temperature helium embrittlement) and a multitude of corrosion and stress corrosion cracking effects (including irradiation-assisted phenomena) that can have a major impact on the performance of structural materials.

nuclear fuels↗

Multimodal Options for Materials Research to Advance the Basis for Fusion Energy in the ITER Era

Well-coordinated international fusion materials research on multiple fundamental feasibility issues can serve an important role during the next ten years. An overview is given of the current state-of-the-art of major materials systems that are candidates for next-step fusion reactors, including a summary of existing knowledge regarding operating temperature and neutron irradiation fluence limits due to high temperature strength and radiation damage considerations, coolant compatibility information, and current industrial manufacturing capabilities. There are two inter-related overarching objectives of fusion materials research to be performed in the next decade: 1) understanding materials science phenomena in the demanding DT fusion energy environment, and 2) Using this improved understanding to develop and qualify materials to provide the basis for next-step facility construction authorization by funding agencies and public safety licensing authorities. The critical issues and prospects for development of high performance fusion materials are discussed along with recent research results and planned activities of the international materials research community.

Zinkle, Steven J↗

Evaluation of irradiation facility options for fusion materials research and development

Successful development of fusion energy will require the design of high-performance structural materials that exhibit dimensional stability and good resistance to fusion neutron degradation of mechanical and physical properties. The high levels of gaseous (H, He) transmutation products associated with deuterium-tritium (D-T) fusion neutron transmutation reactions, along with displacement damage dose requirements up to 50-200 displacements per atom (dpa) for a fusion demonstration reactor (DEMO), pose an extraordinary challenge. The intense neutron source(s) is needed to address two complimentary missions: 1) Scientific investigations of radiation degradation phenomena and microstructural evolution under fusion-relevant irradiation conditions (to provide the foundation for designing improved radiation resistant materials), and 2) Engineering database development for design and licensing of next-step fusion energy machines such as a fusion DEMO. A wide variety of irradiation facilities have been proposed to investigate materials science phenomena and to test and qualify materials for a DEMO reactor. Currently available and proposed facilities include fission reactors (including isotopic and spectral tailoring techniques to modify the rate of H and He production per dpa), dual- and triple-ion accelerator irradiation facilities that enable greatly accelerated irradiation studies with fusion-relevant H and He production rates per dpa within microscopic volumes, D-Li stripping reaction and spallation neutron sources, and plasma-based sources. The advantages and limitations of the main proposed fusion materials irradiation facility options are reviewed. Evaluation parameters include irradiation volume, potential for performing accelerated irradiation studies, capital and operating costs, similarity of neutron irradiation spectrum to fusion reactor conditions, temperature and irradiation flux stability/control, ability to perform multiple-effect tests (e.g., irradiation in the presence of a flowing coolant, or in the presence of complex applied stress fields), and technical maturity/risk of the concept. Ultimately, it is anticipated that heavy utilization of ion beam and fission neutron irradiation facilities along with sophisticated materials models, in addition to a dedicated fusion-relevant neutron irradiation facility, will be necessary to provide a comprehensive and cost-effective understanding of anticipated materials evolution in a fusion DEMO and to therefore provide a timely and robust materials database.

embrittlement↗

Specification of CuCrZr Alloy Properties after Various Thermo-Mechanical Treatments and Design Allowables including Neutron Irradiation Effects

Precipitation hardened CuCrZr alloy is a promising heat sink and functional material for various applica- tions in ITER, for example the first wall, blanket electrical attachment, divertor, and heating systems. Three types of thermo-mechanical treatment were identified as most promising for the various applica- tions in ITER: solution annealing, cold working and ageing; solution annealing and ageing; solution annealing and ageing at non-optimal condition due to specific manufacturing processes for engineer- ing-scale components. The available data for these three types of treatments were assessed and mini- mum tensile properties were determined based on recommendation of Structural Design Criteria for the ITER In-vessel Components. The available data for these heat treatments were analyzed for assess- ment of neutron irradiation effect. Using the definitions of the ITER Structural Design Criteria the design allowable stress intensity values are proposed for CuCrZr alloy after various heat treatments.

36 MATERIALS SCIENCE↗

Effect of H and He Irradiation on Cavity Formation and Blistering in Ceramics

Single- or poly-crystalline specimens of SiC, Si{sub 3}N{sub 4}, MgO, Al{sub 2}O{sub 3} and MgAl{sub 2}O{sub 4} were implanted with 0.4-1 MeV H{sup +} or He{sup +} ion beams at room temperature and 650 C up to fluences of {approx}1 x 10{sup 22}/m{sup 2}. This produced peak implanted gas and displacement damage levels as high as {approx}50 at.% and 34 displacements per atom (dpa). The specimens were subsequently examined optically, and in cross-section using transmission electron microscopy. Subsurface blistering occurred for specimens irradiated to H or He fluences greater than about 3 x 10{sup 21}/m{sup 2} ({approx}15 at.% peak implanted gas concentration), and surface exfoliation occurred for fluences above {approx}1 x 10{sup 22}/m{sup 2} ({approx}40 at.% implanted gas). Both helium and hydrogen had comparable effectiveness for inducing blistering and exfoliation on an atomic basis. The threshold blistering and exfoliation fluences for both ions were weakly dependent on temperature between 25 and 650 C. Both H and He were found to be very effective in inducing matrix cavity formation, due to their low solubility in these ceramics. The implanted gas concentrations that resulted in visible cavity formation generally ranged from 1 to 5 at.%. Visible cavity formation was readily induced during room temperature irradiation despite the limited vacancy mobility in these ceramics at room temperature. Three general types of cavity morphologies were observed: isolated cavities, clusters of small cavities (typically associated with dislocation loops), and two-dimensional platelets. Cavity formation was observed to initiate at the periphery of dislocation loops in some cases. During elevated temperature irradiation, cavity formation was often observed to be preferentially associated with certain low-index habit planes, particularly if the habit plane was oriented nearly parallel to the irradiated surface: (0001) and {l_brace}1{bar 1}00{r_brace} for Al{sub 2}O{sub 3}, (0001) for a-SiC, {l_brace}001{r_brace} and {l_brace}110{r_brace} for MgO, and {l_brace}110{r_brace} and {l_brace}111{r_brace} for MgAl{sub 2}O{sub 4}. The bubble formation and blistering behavior of the ceramics was similar to that observed in other studies of metals irradiated at comparable homologous temperatures. Ionization-induced diffusion effects associated with dual-beam light ion irradiation appeared to exert only a weak effect on cavity and dislocation loop growth compared to the single ion irradiation conditions.

08 HYDROGEN↗

Prospects for Accelerated Development of High Performance Structural Materials

We present an overview of key aspects for development of steels for fission and fusion energy applications, by linking material fabrication to thermo-mechanical properties through a physical understanding of microstructure evolution. Numerous design constraints (e.g. reduced activation, low ductile-brittle transition temperature, low neutron-induced swelling, good creep resistance, and weldability) need to be considered, which in turn can be controlled through material composition and processing techniques. Recent progress in the development of high-performance steels for fossil and fusion energy systems is summarized, along with progress in multiscale modeling of mechanical behavior in metals. Prospects for future design of optimum structural steels in nuclear applications by utilization of the hierarchy of multiscale experimental and computational strategies are briefly described.

36 MATERIALS SCIENCE↗

Influence of Thermal and Radiation Effects on Microstructural and Mechanical Properties of Nb-1Zr

Refractory metals and alloys offer attractive high-temperature properties, most of which are suitable for applications in nuclear environments including high temperature strength, good thermal conductivity, and compatibility with most liquid metal coolants. One of only two commercially produced Nb-alloys, Nb-1Zr has long been considered for various compact reactor designs. Nb-1Zr has also recently been considered for high-performance Gen IV gas reactor concepts. However, there are significant gaps in the irradiated materials database, especially at temperatures above 800 K. Recent work has shown that irradiated properties of Nb-1Zr are strongly controlled by phase-related transformations in the microstructure. Changes in the microstructure (obtained via scanning and transmission electron microscopy) and corresponding mechanical properties of Nb-1Zr were examined following fission reactor irradiation experiments at temperatures of 1073, 1223 and 1373 K to 1.9 dpa (displacements per atom) and compared with material thermally aged for similar exposure times of ~1100 h. Thermally driven changes in the development of precipitate phases showed a greater influence on mechanical properties compared to irradiation-induced defects for these irradiation conditions. The changes in material density, electrical resistivity and mechanical properties of the irradiated and thermally aged materials in association with microstructural developments are discussed.

36 MATERIALS SCIENCE↗

Creep and Fatigue Issues for Structural Materials in Demonstration Fusion Energy Systems

in an environment consisting of intense neutron irradiation, high temperatures, and cyclic varying stress. Therefore, thermal creep and creep-fatigue (in addition to radiation effects issues such as irradiation creep) are anticipated to be important issues for the engineering design of structural materials for fusion reactors. The key materials systems under consideration for structures of fusion reactors include 8-9%Cr ferritic/martensitic steels, oxide dispersion strengthened ferritic steels, vanadium alloys, and SiC fiber-reinforced SiC matrix ceramic composites. The current elevated temperature creep-fatigue design rules based on the American Society of Mechanical Engineers (ASME) code are discussed, along with a brief review of creep-fatigue interaction mechanisms. Refinements to current international design codes to include radiation-induced phenomena such as reduction in uniform elongation have been performed in association with the engineering design of the ITER fusion energy device currently under construction in France. Several other creep-fatigue issues of potential importance for fusion energy applications are discussed.

36 MATERIALS SCIENCE↗

Anomaly in Dependence of Radiation-induced Vacancy Accumulation on Grain Size

According to conventional steady-state rate theory predictions of displacement damage evolution in irradiated materials, the accumulation of vacancies decreases as grain size decreases. Using atomistic simulations, the authors report a transient anomaly in the dependence of radiation produced vacancy accumulation on grain size. Contrary to the conventional wisdom, the accumulation of vacancies can be higher in smaller grains than in larger grains during a transient stage. The anomaly is a result of competition between two atomic-level processes: grain boundary absorption and bulk recombination of point defects, each of which has characteristic length and time scales. A simple metal copper is used as the prototype of face-centered cubic material and electron radiation is the source of non-cascade defect production, both choices aiming at clarity for identifying physical mechanisms.

36 MATERIALS SCIENCE↗

Irradiation creep of the US Heat 832665 of V-4Cr-4Ti

The paper presents irradiation creep data for V-4Cr-4Ti irradiated to 3.7 dpa at 425 and 600 _C in the HFIR-17J experiment. Creep deformation was characterized by measuring diametral changes of pressur-ized creep tubes before and after irradiation. It was found that the creep strain rate of the US Heat 832665 of V-4Cr-4Ti exhibited a linear relationship with stress up to _180 MPa at 425 _C with a creep coefficient of 2.50 _10_6 MPa_1 dpa_1. A linear relationship between creep rate and applied stress was observed below _110 MPa at 600 _C with a creep coefficient of 5.41 _10_6 MPa_1 dpa_1; non-linear creep behavior was observed above _110 MPa, and it may not be fully accounted by invoking thermal creep. The bilinear creep behavior observed in the same alloy irradiated in BR-10 was not observed in this study.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗