Search NASA⌕ Search

Engineering topics

Zipperer, Travis J.

Publications and source records attributed to Zipperer, Travis J..

Estimating the Contribution of the Nickel to Protium Loading of Full-Length Getters

The full-length getter (FLG) is a critical component of the tritium producing burnable absorber rod (TPBAR), designed to capture tritium produced within the lithium aluminate pellets. However, due to the chemical similarity between protium (¹H) and tritium (³H), the FLG readily absorbs protium, reducing its capacity to absorb tritium and increasing the risk of tritium permeation into the reactor coolant. This study evaluates protium produced from neutron irradiation of nickel plating on the FLG through 5?Ni(n,p) reactions, quantifies its contribution to the total protium observed, and informs models of tritium and hydrogen transport within TPBARs. During irradiation, neutron capture by 58Ni results in the formation of 5?Ni, which undergoes neutron bombardment to produce 4He via 5?Ni(n,a) reactions and protium via 5?Ni(n,p) reactions. The measured helium content post-irradiation provides insight into the neutron capture processes within the getter. The 4He measured within the getter may be useful in determining hydrogen produced by the nickel plating on FLG because 59Ni also produces protium in a 59Ni(n, p) reaction. The contribution of 1H from the nickel in FLG contributed less than 1% of the measured H2 gas in PIE, ranging from 0.005% to 0.614%. These findings refine current knowledge of the protium-tritium interplay in TPBARs and support the development of improved transport models for tritium and hydrogen, ultimately aiding in the optimization of TPBAR design and reactor operations.

Arbova, Dana L.↗

Sum-of-Fractions Methodology for Actinides in Water- and Polyethylene-Moderated and -Reflected Systems

Sum-of-fractions is a method intended to make sure a subcritical margin for aqueous solutions and slurries of fissionable isotopes exists. The method indicates that a system is subcritical if the sum of the ratios of the mass of each isotope (in a mixture) to its individual minimum subcritical mass limit is less than or equal to one. Historically, the basis of the sum-of-fractions has been derived from allowances given in the American National Standards Institute (ANSI)/ American Nuclear Society (ANS)-8.15-1981. However, the allowance was removed in ANSI/ANS-8.15-2014 due to a lack of technical basis. A methodology was developed to assess the validity of using the sum-of-fractions for water- or polyethylene-moderated systems for the following nuclides: 232 U, 233 U, 234 U, 235 U, 237 Np, 236 Pu, 238 Pu, 239 Pu, 240 Pu, 241 Pu, 242 Pu, 241 Am, 242 m Am, 243 Am, 242 Cm, 243 Cm, 244 Cm, 245 Cm, 246 Cm, 247 Cm, 249 Cf, and 251 Cf. The methodology uses available benchmark data for mixtures of 233 U, 235 U, and 239 Pu to establish the calculational margin, and a mass limit reduction to establish the margin of subcriticality. Water- or polyethylene-moderated and -reflected mixtures containing the nuclides are evaluated with the code system, SCALE 6.2.4. Including the calculational margin, subcritical mass limits for each nuclide were computed for optimally water- or polyethylene-moderated and fully reflected systems. These masses were used to create nuclide mixtures in which the sum of the mass to subcritical mass limit ratios is one. The various nuclide mixtures were modeled over a range of moderation and demonstrate the keff does not exceed the calculational margin. For additional assurance of subcriticality, a significant mass reduction is applied to each computed minimum critical mass of the nuclides without adequate benchmark data consistent with the method in ANSI/ANS-8.15-2014.

07 ISOTOPE AND RADIATION SOURCES↗

Evaluation of the Sum-of-Fractions Methodology for Water and Polyethylene Moderated Systems

Sum-of-Fractions is a method intended to assure a subcritical margin for aqueous solutions and slurries of fissionable isotopes. The method indicates that a system is subcritical if the sum of the ratios of the mass of each isotope in a mixture to its individual minimum subcritical mass limit is less than or equal to one. The basis of the Sum-of Fractions has historically been derived from allowances given in ANSI/ANS-8.15-1981. However, the allowance was removed in ANSI/ANS-8.15-2014 due to a lack of technical basis. A methodology was developed to assess the validity of using the Sum-of-Fractions for water or polyethylene moderated systems for the following nuclides: 232 U, 233 U, 234 U, 235 U, 237 Np, 236 Pu, 238 Pu, 239 Pu, 240 Pu, 241 Pu, 242 Pu, 241 Am, 242 mAm, 243 Am, 242 Cm, 243 Cm, 244 Cm, 245 Cm, 246 Cm, 247 Cm, 249 Cf, and 251 Cf. The methodology uses available benchmark data for mixtures of 233 U, 235 U, and 239 Pu to establish the calculational margin, and a mass limit reduction to establish the margin of subcriticality. Water or polyethylene moderated and reflected mixtures containing the nuclides are evaluated with SCALE 6.2.4. Including the calculational margin, subcritical mass limits for each nuclide were computed for optimally water or polyethylene moderated and fully reflected systems. These masses were used to create nuclide mixtures in which the sum of the mass to subcritical mass limit ratios is one. The various nuclide mixtures were modeled over a range of moderation and demonstrate the k eff does not exceed the calculational margin. For additional assurance of subcriticality, a significant mass reduction is applied to each computed minimum critical mass of the nuclides without adequate benchmark data consistent with the method in ANSI/ANS-8.15-2014.

07 ISOTOPE AND RADIATION SOURCES↗

FAST-1.2 User Installation and Verification Guide: Developed Under NQA-1-2017

The purpose of this document is to provide the user information about the installation of Fuel Analysis for Steady state and Transient (FAST)-1.2 on their computers or servers. General information about the code and supported operating systems is described in Section 1.0. Self-service oriented FAST-1.2 software licensing steps are described in Section 2.0. An installation verification test suite is provided with FAST-1.2 and described in Section 3.0. A convenience script for converting Fuel Rod Analysis Program – Constant (FRAPCON) to FAST inputs is discussed in Section 4.0. FAST-1.2 was developed and released under a software quality assurance program based upon NQA-1-2017 at Pacific Northwest National Laboratory (PNNL). FAST-1.2 is the latest baseline code. The installation verification test suite contains both steady state and transient Anticipated Operation Occurrences (AOOs), accident conditions, such as Reactivity Initiated Accidents (RIAs) and Loss of Coolant Accidents (LOCAs).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FAST-1.1: Integral Assessment

An integral assessment has been performed to quantify the predictive capabilities of FAST, a thermal-mechanical nuclear fuel performance code designed to analyze fuel behavior from beginning of life to burnup levels allowed by the U.S. Nuclear Regulatory Commission (NRC). FAST code calculations are shown to compare satisfactorily to a preselected set of experimental data with both steady-state and anticipated operating occurrence (AOO) conditions and design basis accident (DBA) transient operating conditions. This document describes the assessment of FAST-1.1, the latest version of FAST, released April 2022. Abstract

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FAST-1.0.1 User Installation and Verification Guide

The purpose of this document is to provide the user information about the installation of FAST-1.0.1 on their computers or servers. General information about the code and supported operating systems is described in Section 1.0.1. Self-service oriented FAST-1.0.1 software licensing steps are described in Section 2.0. An installation verification test suite is provided with FAST-1.0.1 and described in Section 3.0. A convenience script for converting FRAPCON to FAST inputs is discussed in Section 4.0. FAST-1.0.1 was developed and released under a software quality assurance program based upon NQA-1-2017. FAST-1.0.1 is the latest baseline code and the result of a bug fixes to FAST-1.0 with other software and methodology developments. The installation verification test suite contains both steady state and transient Anticipated Operation Occurrences (AOOs). Capability to model accident conditions, such as Reactivity Initiated Accidents (RIAs) and Loss Of Coolant Accidents (LOCAs), are targeted for a later release of FAST. FRAPTRAN-2.0 will continue to be used for accident conditions until the release of FAST with accident condition modeling capabilities.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Criticality Safety and Fuel Performance Considerations for Enrichment Above 5 Weight Percent in the Uranium Dioxide Fuel Cycle

The U.S. Nuclear Regulatory Commission (NRC) is preparing for anticipated licensing applications requesting fuel enrichments of UO 2 ceramic fuels enriched in excess of 5 weight percent (w/o) 235 U for commercial light-water reactors (LWRs). PNNL has been tasked with providing technical assistance to the NRC related to the review and approval of requests for enrichment increases above the current 5 w/o 235 U enrichment limit. This report will provide the agency with technical assistance to enhance the staff’s knowledge base and to identify developmental needs required to support the licensing of greater than 5 w/o UO 2 ceramic fuels. This report provides a background on increasing enrichment of UO 2 LWR fuel beyond 5 w/o 235 U. The primary concern of increasing enrichment is the impacts to criticality safety. This report will focus on criticality safety as it relates to enrichment, conversion of uranium hexafluoride to UO 2 , fuel assembly fabrication, transportation of fresh/spent fuel assemblies, reactor operations, and storage of fresh/spent fuel assemblies. The report provides a general summary of each of the steps in the UO 2 fuel cycle starting from transportation of enriched UF 6 through dry cask storage of spent fuel assemblies. This report also discusses other impacts of increased enrichment during reactor operation and the surrounding fuel cycle activities. Current needs regarding both data and analytical codes to support the increase above 5 w/o 235 U are identified and discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FAST-1.0: Integral Assessment: Developed under NQA-1-2017

An integral assessment has been performed to quantify the predictive capabilities of FAST, a thermal-mechanical nuclear fuel performance code designed to analyze fuel behavior from beginning of life to burnup levels allowed by the U.S. Nuclear Regulatory Commission (NRC). FAST code calculations are shown to compare satisfactorily to a preselected set of experimental data with both steady-state, anticipated operating occurrence (AOO) and design basis transient operating conditions. This document describes the assessment of FAST-1.0, which is the latest version of FAST, released February 2020.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FAST-1.0 Software Acceptance Testing Report

The purpose of this document is to detail the software testing of FAST-1.0 through unit, integration, and assessment tests. More than 400 tests were designed to provide coverage of the requirements for FAST-1.0. These requirements were developed in the NRC Statement of Work (SOW) for NRC Agreement Number NRC-HQ-25-14-D-001 and are transcribed to this document as part of the Software Quality Assurance Plan for the FAST Code System, PNNL-28767. FAST 1.0 represents the merger of the FRAPCON and FRAPTRAN codes and as such FAST-1.0 performs steady state and transient fuel performance calculations described below. FAST-1.0 calculates the steady state response of light-water reactor fuel rods during long-term burnup. The code calculates temperature, pressure, and deformation of a fuel rod as functions of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by the code include: 1) heat conduction through fuel and cladding to the coolant; 2) cladding elastic and plastic deformation; 3) fuel-cladding mechanical interaction; 4) fission gas release from the fuel and rod internal pressure; and 5) cladding oxidation. FAST is used to perform independent calculations for regulatory evaluations of fuel performance under normal operation and anticipated operational occurrences (AOOs). FAST calculates the temperature and deformation history of a fuel rod as a function of time-dependent fuel rod power and coolant boundary conditions. The phenomena modeled by FAST include: 1) heat conduction; 2) heat transfer from cladding to coolant; 3) elastic-plastic fuel and cladding deformation; 4) cladding oxidation; 5) fission gas release; and 6) fuel rod gas pressure. FAST code assessment, development and maintenance drive a significant portion of the NRC fuel research activities and the tools are used in a substantial number of regulatory products. Given the centrality of the FAST code to the effectiveness of fuel research, it is critical to assess, develop and maintain this tool.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Final Report on the Viability of Acoustic Techniques for Density and Mass Flow in Enrichment Plants

The primary purpose of this research is to study the viability of acoustic signatures and sensors that could support accurate, noninvasive, and unattended measurement of uranium hexafluoride (UF6) gas density and mass flow rate in situations representative of gaseous centrifuge enrichment plants (GCEP) under safeguards by the International Atomic Energy Agency. The measurement method under development can be readily retrofitted to the exterior of piping in existing systems, potentially facilitating acceptance by facility operators. The findings from the demonstration of a preliminary prototype design and first-generation analysis algorithms in this project will inform the safeguards community as to whether continued acoustic instrument and methods development are warranted. This project conducted two types of measurements, depending on the flow conditions of the gas. For static measurements, the focus is on understanding the acoustic properties at low pressure for non-flowing UF6. For flow measurements, the focus is on understanding the performance of the acoustic system in a simulation of a GCEP pipe using a surrogate gas under fully developed flow conditions. Testing with flowing UF6 was not considered because the cost of building a flowing UF6 system with flow similar to a GCEP was considerably greater than allocated project resources. This document summarizes the results of research conducted over the course of the project. Based on the results to date, the approach is seen to be promising with non-invasive acoustic measurements shown to be possible at the desired pressures. The project has demonstrated • 5% uncertainty of the UF6 gas density for static measurements at pressures relevant to GCEP operations over a 5-minute measurement window with a clear path forward to achieving considerably lower uncertainties over a two-hour period, • Measurements of flowing surrogate gases at pressures relevant to GCEP operations. However, additional research remains to be done to further develop the measurement approach and transition the technology for field use. These development needs include: • Understand the impact of flowing gas on gas density measurements, • Adding sensors and improving the measurement procedure, • Augmenting the data analysis methods by leveraging machine learning approaches, • Reevaluating uncertainty requirements for density and mass flow given observed Online Enrichment Monitor (OLEM) measurement uncertainties, • Designing a robust instrumentation package for field-testing, and • Evaluating measurement results to understand the potential impact on mass balance calculations within GCEP facilities.

42 ENGINEERING↗