Engineering topics
Publications and source records attributed to Zuk, J..
Program calculates mass and volume leakage across seal; mean friction factor; force; center of pressure; and distributions of pressure, temperature, density, friction parameter, velocity, and Mach number across seal for both laminar flow and turbulent flow regimes and for choked and subsonic flow.
The load factor is investigated for subsonic and choked flow conditions, laminar and turbulent flows, and various seal entrance conditions. Both parallel sealing surfaces and surfaces with small linear deformation were investigated. The load factor for subsonic flow depends strongly on pressure ratio; under choked flow conditions, however the load factor is found to depend more strongly on film thickness and flow entrance conditions rather than pressure ratio. The importance of generating hydrodynamic forces to keep the seal balanced under severe and multipoint operation is also discussed.
Proper pressure balancing of gas film seals requires knowledge of the pressure profile load factor (load factor) values for a given set of design conditions. In this study, the load factor is investigated for subsonic and choked flow conditions, laminar and turbulent flows, and various seal entrance conditions. Both parallel sealing surfaces and surfaces with small linear deformation were investigated. The load factor for subsonic flow depends strongly on pressure ratio; under choked flow conditions, however, the load factor is found to depend more strongly on film thickness and flow entrance conditions rather than pressure ratio. The importance of generating hydrodynamic forces to keep the seal balanced under severe and multipoint operation is also discussed.
Design adds gas thrust bearing to face of conventional face seal. Bearing lifts seal's carbon face out of contact after startup and establishes thin gas film between sealing surfaces. Operating pressure and speed capabilities are greater than those of conventional face seals.
A computer program is presented for compressible fluid flow with friction across face seals and through narrow slots. The computer program carries out a quasi-one-dimensional flow analysis which is valid for laminar and turbulent flows under both subsonic and choked flow conditions for parallel surfaces. The program is written in FORTRAN IV. The input and output variables are in either the International System of Units (SI) or the U.S. customary system.
An analysis is presented for compressible fluid flow across shaft face seals and narrow slots. The analysis includes fluid inertia, viscous friction, and entrance losses. Subsonic and choked flow conditions can be predicted and analyzed. The model is valid for both laminar and turbulent flows. Results agree with experiment and with solutions which are more limited in applicability. Results show that a parallel film can have a positive film stiffness under choked flow conditions.
Explore the source record for details and available documents.
A method for predicting the operating film thickness of self-acting seals is described. The analysis considers a 16.76-cm mean diameter seal that is typical of large gas turbines for aircraft. Four design points were selected to cover a wide range of operation for advanced engines. This operating range covered sliding speeds of 61 to 153 m/sec, sealed pressures of 45 to 217 N/sq cm abs, and gas temperatures of 311 to 977 K. The force balance analysis revealed that the seal operated without contact over the operating range with gas film thicknesses ranging between 0.00046 to 0.00119 cm, and with gas leakage rates between 0.01 to 0.39 scmm.
Analyses are presented for compressible fluid flow across shaft face seals with face deformation. The solutions are obtained from an approximate integral analysis. The models, used in this analysis, can predict gas film seal behavior operating at subsonic or choked flow conditions. The flow regime can either be laminar or turbulent. Entrance losses can also be accounted for. When fluid inertia effects are negligible and the sealing faces are slightly deformed, the following results are found for both laminar and turbulent flows: (1) The pressure profiles are independent of fluid properties; and (2) the parallel film leakage equation can be used, provided a characteristic film thickness is used. Pressure profiles are presented for both divergent and convergent seal faces under choked flow conditions.
Rotational effects on laminar subsonic compressible viscous flow across shaft face seals, noting leakage rates and pressure profiles
Computer program for numerical analysis of flow and pressure distribution in idealized spiral grooved pumping seal
Compressible flow across shaft face seals and narrow slots, examining fluid inertia, viscous friction and entrance losses
Analysis of compressible flow across shaft face seals
Physical properties and rotational effects on isothermal compressible flow across shaft seals
Sealing dam analysis for design of shaft face seal with self-acting lift augmentation for advanced gas turbine engines
Computerized analysis of seal temperature, elastic displacements and seal force balance in iterative design method for gas turbine mainshaft seals
Computer program analyzes the flow /leakage/ across a sealing dam for the case of steady, laminar, subsonic, isothermal, compressible flow. The analysis considers both parallel sealing-dam surfaces and surfaces with small tilt angles.
Parametric design study of self-acting pad geometries for shaft seals in turbocompressors