Engineering topics

Zumwalt, Carlie H.

Publications and source records attributed to Zumwalt, Carlie H..

6 records

NASA NTRS2016

Wind Tunnel Test of Subscale Ringsail and Disk-Gap-Band Parachutes

A subsonic wind tunnel test was conducted to determine the drag and static aerodynamic coefficients, as well as to capture the dynamic motions of a new Supersonic Ringsail parachute developed by the Low Density Supersonic Decelerator Project. To provide a comparison against current Mars parachute technology, the Mars Science Laboratory's Disk-Gap-Band parachute was also included in the test. To account for the effect of fabric permeability, two fabrics ("low" and "standard" permeability) were used to fabricate each parachute canopy type, creating four combinations of canopy type and fabric material. A wide range of test conditions were covered during the test, spanning Mach numbers from 0.09 to 0.5, and static pressures from 103 to 2116 pounds per square inch (psf) (nominal values). The fabric permeability is shown to have a first-order effect on the aerodynamic coefficients and dynamic motions of the parachutes. For example, for a given parachute type and test condition, models fabricated from "low" permeability fabric always have a larger drag coefficient than models fabricated from "standard" permeability material. This paper describes the test setup and conditions, how the results were analyzed, and presents and discusses a sample of the results. The data collected during this test is being used to create and improve parachute aerodynamic databases for use in flight dynamics simulations for missions to Mars.

Zumwalt, Carlie H.↗

NASA NTRS2015

High Altitude Venus Operations Concept Trajectory Design, Modeling and Simulation

A trajectory design and analysis that describes aerocapture, entry, descent, and inflation of manned and unmanned High Altitude Venus Operation Concept (HAVOC) lighter-than-air missions is presented. Mission motivation, concept of operations, and notional entry vehicle designs are presented. The initial trajectory design space is analyzed and discussed before investigating specific trajectories that are deemed representative of a feasible Venus mission. Under the project assumptions, while the high-mass crewed mission will require further research into aerodynamic decelerator technology, it was determined that the unmanned robotic mission is feasible using current technology.

Lugo, Rafael A.↗

NASA NTRS2011

Entry, Descent and Landing Systems Analysis Study: Phase 2 Report on Exploration Feed-Forward Systems

NASA senior management commissioned the Entry, Descent and Landing Systems Analysis (EDL-SA) Study in 2008 to identify and roadmap the Entry, Descent and Landing (EDL) technology investments that the agency needed to successfully land large payloads at Mars for both robotic and human-scale missions. Year 1 of the study focused on technologies required for Exploration-class missions to land payloads of 10 to 50 t. Inflatable decelerators, rigid aeroshell and supersonic retro-propulsion emerged as the top candidate technologies. In Year 2 of the study, low TRL technologies identified in Year 1, inflatables aeroshells and supersonic retropropulsion, were combined to create a demonstration precursor robotic mission. This part of the EDL-SA Year 2 effort, called Exploration Feed Forward (EFF), took much of the systems analysis simulation and component model development from Year 1 to the next level of detail.

Dwyer Ciancolo, Alicia M.↗

NASA NTRS2010

Aerocapture Guidance and Performance at Mars for High-Mass Systems

The objective of this study is to understand the performance associated with using the aerocapture maneuver to slow high-mass systems from an Earth-approach trajectory into orbit around Mars. This work is done in conjunction with the Mars Entry Descent and Landing Systems Analysis (EDL-SA) task to explore candidate technologies necessary for development in order to land large-scale payloads on the surface of Mars. Among the technologies considered include hypersonic inflatable aerodynamic decelerators (HIADs) and rigid mid-lift to drag (L/D) aeroshells. Nominal aerocapture trajectories were developed for the mid-L/D aeroshell and two sizes of HIADs, and Monte Carlo analysis was completed to understand sensitivities to dispersions. Additionally, a study was completed in order to determine the size of the larger of the two HIADs which would maintain design constraints on peak heat rate and diameter. Results show that each of the three aeroshell designs studied is a viable option for landing high-mass payloads as none of the three exceed performance requirements.

Zumwalt, Carlie H.↗

NASA NTRS2010

Entry, Descent and Landing Systems Analysis Study: Phase 1 Report

DwyerCianciolo, Alicia M.↗

NASA NTRS2009

Aerocapture Guidance and Performance at Mars for High-Mass Systems

The Mars Entry, Descent, and Landing System Analysis (EDL-SA) project has been tasked with performing systems analysis to identify the optimal technologies required to land a 20-50 MT Exploration-class mission on Mars. It has been shown that it is not possible to safely land these large systems using heritage Mars EDL systems, or analogous Earth or Moon EDL systems. In 2007, NASA conducted a Mars Exploration Architecture Study which included an in depth review of the science motivations and engineering technology requirements for a human Mars mission campaign. This study resulted in an update to the Mars Design Reference Architecture (DRA 5.0). Among the primary findings and recommendations was the conclusion that landing of large payloads (greater than 1 MT) on the surface of Mars remains a key architectural challenge. Additionally, research and system studies of fundamental EDL technologies were highly recommended. The EDL-SA project identified the candidate technologies and assembled them into full capture and EDL sequences so that simulations could be developed to evaluate them. The chosen architectures combine the various technologies of interest in eight different ways. For aerocapture, only two scenarios were considered. The first is a rigid mid-L/D aeroshell (AS), which is represented in architectures 1, 4, 5, and 7. This scenario calls for a vehicle that flies at a 55-degree angle of attack, resulting in ballistic coefficient and L/D values of 490 kg/m 2 and 0.43, respectively. The second is a lifting hypersonic inflatable aerodynamic decelerator (HIAD), which is represented in architectures 2, 6, and 8. This scenario requires the vehicle to fly at a 22.2- degree angle of attack, which correlates to an L/D of 0.3 and was sized to provide a ballistic coefficient of 165 kg/m 2 . Architecture 3 is an all-propulsive sequence, and is not considered in this study.

Zumwalt, Carlie H.↗