Engineering topics

deGroh, H., III

Publications and source records attributed to deGroh, H., III.

3 records

NASA NTRS2001

In Situ Monitoring of Crystal Growth Using Mephisto

Experiments were carried out to study the morphological stability of Bi-1atomic% Sn alloys using the MEPHISTO directional solidification apparatus aboard Space Shuttle Columbia (STS-87, launched November 19, 1997). The research program involved collaboration of the University of Florida, Centre National d'Etudes Spatiales (France), NASA/Glenn Research Center, the National Institute of Standards and Technology, and the University of New South Wales (Australia). The experiments made use of the Seebeck technique to measure the interface temperature, the resistance change across the sample for determination of the interface velocity, and Peltier current pulsing for demarcation of the interface shape. These data were obtained in real-time during various melting/solidification cycles, and the experiments were controlled via telecommands. The Seebeck signal and temperature measurements in the space experiments, as well as morphological behavior of the solid/liquid interface, were found to be significantly different than those obtained from ground-based studies. For the space-based experiments, interface breakdown was observed at growth velocities of 6.7, 27, and 40 micrometers/s, but not at 1.8 and 3.3 micrometers/s. The results further indicate that the morphological stability threshold for some grain orientations is significantly enhanced, resulting in a staggered planar to cellular transition front. This report summarizes some of these findings.

Abbaschian, Reza↗

NASA NTRS1999

In Situ Monitoring of Crystal Growth Using MEPHISTO, Mission STS 87-Program USMP-4: Experimental Analysis

This report summarizes the results of the In situ Monitoring of Crystal Growth Using MEPHISTO (Material por l'Etude des Phenomenes Interessant de la Solidification sur Terre et en Orbite) experiment on USMP-4. The report includes microstructural and compositional data obtained during the first year of the post flight analysis, as well as numerical simulation of the flight experiment. Additional analyses are being continued and will be reported in the near future. The experiments utilized MEPHISTO hardware to study the solidification and melting behavior of bismuth alloyed with 1 at% tin. The experiments involved repeated melting and solidification of three samples, each approximately 90 cm long and 6mm in diameter. Half of each sample also included a 2 mm. diameter growth capillary, to assist in the formation of single grain inside. One sample provided the Seebeck voltage generated during melting and freezing processes. Another one provided temperature data and Peltier pulsed demarcation of the interface shape for post flight analysis. The third sample provided resistance and velocity measurements, as well as additional thermal data. The third sample was also quenched at the end of the mission to preserve the interface composition for post flight determination. A total of more than 45cm of directionally solidified alloy were directionally solidified at the end of the flight for post mission structural and compositional characterization. Metallurgical analysis of the samples has shown that the interfacial kinetics play a key role in controlling the morphological stability of faceted alloys. Substantial differences were observed in the Seebeck signal between the ground-based experiments and the space-based experiments. The temperature gradient in the liquid for the ground-based experiments was also significantly lower than the temperature gradient in the liquid for the space-based experiments. Both of these observations indicate significant influence of liquid convection for the ground-based experiments.

Abbaschian, Reza↗

NASA NTRS1999

Directional Solidification of Bi-Sn on USMP-4

The experiments used MEPHISTO hardware to study the solidification and melting behavior of bismuth alloyed with 1 at% tin. Three samples, each approximately 900 mm long and 6mm in diameter, were used. A portion of each sample also included a 2 mm diameter growth capillary, to assist in the formation of a single grain. One sample provided the Seebeck voltage generated during melting and freezing processes. Another provided temperature data and Peltier pulsed demarcation of the interface shape for post flight analysis. The third sample provided resistance and growth velocity measurements, as well as additional thermal data. The third sample was also quenched at the end of the mission to preserve the composition of the liquid near the interface for post flight determination. A total of 450mm of directionally solidified samples were preserved for post mission structural and compositional characterization. Substantial differences were observed in the Seebeck signal between the ground-based experiments and the space-based experiments. The temperature gradient in the liquid for the ground-based experiments was significantly lower than the temperature gradient in the liquid for the space-based experiments.

Abbaschian, Reza↗