Search NASA⌕ Search

Engineering topics

van Veelen, Arjen

Publications and source records attributed to van Veelen, Arjen.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Performance and properties evolution of near-term accident tolerant fuel: Cr-doped UO 2

Chromium-doped UO 2 fuel has received significant interest due to the ability for chromium to produce pellets with large average grain size (>30 μm), which has shown to increase fission gas retention during operation. Sintering of chromium-doped UO 2 pellets was pursued with oxygen potential and sintering atmosphere controlled to tailor the final microstructure of the material. Chromium additions in this study ranged from 750 to 7800 ppm. Cr concentrations were studied pre and post sintering using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Effects of chromium content on lattice parameter and microstructure were examined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Contraction of the UO 2 lattice parameter was observed, as well as enlargement of grain size with increasing chromium content up to 4900 ppm Cr 2 O 3 . In addition, SEM indicated Cr incorporation within the matrix and the formation of chromium oxide precipitates throughout the microstructure at high Cr concentrations. Evaluation of thermophysical properties of Cr-doped UO 2 pellets were conducted up to 1200 °C to illustrate their evolution with increased dopant concentration and microstructural changes. The results show that grain size is maximized at 52 μm with Cr 2 O 3 concentration equal to 4900 ppm; however, grain size decreases at higher Cr 2 O 3 concentrations. No significant changes were observed in specific heat capacity, linear thermal expansion, and coefficient of thermal expansion compared to undoped UO 2 . The thermal conductivity also decreased through the incorporation of Cr 2 O 3 dopants above 750 ppm and is shown to be ~15 % lower than reported UO 2 values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

The effects of hydrogen absorption in U 3 Si 5 and its thermodynamic properties

The hydrogen absorption behavior of U 3 Si 5 was examined using a Sieverts apparatus. Experimental results revealed the formation of a hydride phase with a stoichiometry reaching U 3 Si 5 H 1.23 at pressures up to 250 kPa and temperatures below 300°C. Further, by employing Van 't Hoff analysis, the enthalpy and entropy of formation for the newly formed hydride phase were measured as -19.73 $kJ$ ∙ $mol$ -1 and -251.18 $J$ ∙ $mol$ -1 ∙ $T$ -1 , respectively. Rietveld refinement showcased an expansion in lattice parameters a and c, resulting in an overall increase in unit cell volume of up to 8%; volume expansion can induce structural failures within the material.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Energetics of oxidation and formation of uranium monocarbide

To enable better implementation of uranium monocarbide (UC) as an advanced nuclear fuel for future high-temperature reactors, it is essential to have a thorough knowledge of its thermal and thermodynamic properties under reactor operational conditions. In this work, we studied thermal bulk oxidation of UC by simultaneous thermal analysis consisting of thermogravimetric analysis – differential scanning calorimetry coupled with evolved gas mass spectrometry (TGA-DSC-MS), and we examined the thermodynamic stability of UC using high temperature oxide melt drop solution calorimetry. Further, in air, our studied UC sample (which contains ~5 mol% UO 2 ) was found to undergo a step-wise thermal oxidation process consisting of consecutive oxidations and thermal decomposition reactions: 0.95UC·0.05UO 2 → UO 3 ·0.29(C x O y ) + 0.66CO 2 → UO 3 ·0.20(C x O y ) + 0.09CO 2 → UO 3 ·0.03(C x O y ) + 0.17CO 2 → U 3 O 8 + 0.03CO 2 + 0.166O 2 . DSC was further used to determine the enthalpies of reactions associated with this series of oxidation reactions. Synchrotron X-ray diffraction (XRD) and extended X-ray absorption spectroscopy (EXAFS) were performed to characterize both the long- and short-range structures of UC. The standard enthalpy of formation (ΔH° f ) of UC was determined to be –50.7 ± 10.8 kJ/mol·atom, in good agreement with previous values measured by bomb calorimetry. Lastly, the enthalpic landscape of U-C compounds, including UC, U 2 C 3 , and α-UC 1.94 , were established based on the enthalpy normalized per mole atom, which suggests that U-C phases are thermodynamically stable at lower C/U ratios.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Finite temperature properties of uranium mononitride

Uranium mononitride (UN) is a promising nuclear fuel that combines the advantageous properties of readily used UO 2 and uranium alloys, such as high melting temperature and high uranium density, and thermal conductivity, respectively. A better understanding of UN behavior at operating temperatures can be obtained from finite temperature data, such as elastic properties. To get this information, ab initio molecular dynamics (AIMD) simulations were performed at five different temperatures using constant volume (NVT) and constant pressure (NPT) ensembles. Initially, the performance of PBE functional in reproducing experimental crystallographic properties and magnetic ordering is assessed. The finite temperature phonon dispersions are calculated using NVT simulation results, which show a softening of the phonon modes with increasing temperature. The NPT results are used to obtain the thermal expansion of UN and finite temperature electronic properties. The calculated thermal expansion is compared with our measurements using neutron diffraction. Additionally, the temperature dependent elastic properties of UN are evaluated using the strain-stress method in AIMD simulations, indicating that UN becomes softer and more compressible with increasing temperature. Also, the calculated Young’s modulus slope is in very good agreement with the experiment. The finite temperature heat capacity and electronic thermal conductivity are calculated from AIMD simulations, which are in better agreement with the experiment than the heat capacity and thermal conductivity calculated using the structures relaxed at 0K. Finally, the thermal diffusivity from AIMD has opposite temperature dependence compared to experimental results, which we argued comes from the underestimated electronic thermal conductivity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

A new μ -high energy resolution fluorescence detection microprobe imaging spectrometer at the Stanford Synchrotron Radiation Lightsource beamline 6-2

In this report we describe a new synchrotron X-ray Fluorescence (XRF) imaging instrument with an integrated High Energy Fluorescence Detection X-ray Absorption Spectroscopy (HERFD-XAS) spectrometer at the Stanford Synchrotron Radiation Lightsource at beamline 6-2. The X-ray beam size on the sample can be defined via a range of pinhole apertures or focusing optics. XRF imaging is performed using a continuous rapid scan system with sample stages covering a travel range of 250 × 200 mm 2 , allowing for multiple samples and/or large samples to be mounted. The HERFD spectrometer is a Johann-type with seven spherically bent 100 mm diameter crystals arranged on intersecting Rowland circles of 1 m diameter with a total solid angle of about 0.44% of 4π sr. A wide range of emission lines can be studied with the available Bragg angle range of ~64.5°–82.6°. With this instrument, elements in a sample can be rapidly mapped via XRF and then selected features targeted for HERFD-XAS analysis. Furthermore, utilizing the higher spectral resolution of HERFD for XRF imaging provides better separation of interfering emission lines, and it can be used to select a much narrower emission bandwidth, resulting in increased image contrast for imaging specific element species, i.e., sparse excitation energy XAS imaging. This combination of features and characteristics provides a highly adaptable and valuable tool in the study of a wide range of materials.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

Energetics of oxidation and formation of uranium mononitride

Uranium mononitride (UN) is an advanced nuclear fuel currently being considered for use in several generation IV fast and thermal neutron spectrum core designs, with additional applications to thermal and electric nuclear propulsion reactors. Here, to better understand the thermal behavior and thermodynamic stability of UN, we investigated the bulk thermal oxidation process and thermochemical reactions, including the enthalpy of oxidation and standard enthalpy of formation, by conducting thermalgravimetric analysis – differential scanning calorimetry coupled with mass spectrometry (TGA-DSC-MS), and high temperature transposed temperature drop and oxide melt drop solution calorimetry. The bulk oxidation of UN (containing a small amount of α-UN 1.5+x ) in air was found to follow a step-wise process characterized by consecutive oxidative reactions UN-UN 1.5+x -UO 2 → UO 2 -UO 3 —N k → UO 3 —N k → UO 3 → U 3 O 8 . TGA results support that the UO 2 – U 2 N 3+x passivating layer delays the onset of rapid bulk oxidation of UN in air up to 662 K. Synchrotron X-ray diffraction (XRD) and extended X-ray absorption fine structure (EXAFS) analyses were performed to characterize UN and its final oxidized product. The standard enthalpy of formation (ΔH° f ) of UN was determined to be –144.4 ± 5.9 kJ/mol·atom, in good agreement with previously determined values from Pt encapsulation and bomb calorimetric experiments. Lastly, a negative linear correlation between ΔH° f and the N/U molar ratio was established based on the thermochemical data obtained in this work and previously reported enthalpies of formations of β-UN 1.5-x and α-UN 1.5+x .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Trace Impurities Identified as Forensic Signatures in CMX-5 Fuel Pellets Using X-ray Spectroscopic Techniques

We report that small-particle analysis is a highly promising emerging forensic tool for analysis of interdicted special nuclear materials. Integration of microstructural, morphological, compositional, and molecular impurity signatures could provide significant advancements in forensic capabilities. We have applied rapid, high-sensitivity, hard X-ray synchrotron chemical imaging to analyze impurity signatures in two differently fabricated fuel pellets from the 5th Collaborative Materials Exercise (CMX5) of the IAEA Nuclear Forensics International Working Group. The spatial distributions, chemical compositions, and morphological and molecular characteristics of impurities were evaluated using X-ray absorption near-edge structure (XANES) and X-ray fluorescence chemical imaging to discover principal impurities, their granularity, particle sizes, modes of occurrence (distinct grains vs incorporation in the UO 2 lattice), and sources and mechanisms of incorporation. Differences in UO 2+x stoichiometry were detected at the microscale in nominally identical UO 2 ceramics (CMX5-A and CMX5-B), implying the presence of multiple UO 2 host phases with characteristic microstructures and feedstock compositions. Al, Fe, Ni, W, and Zr impurities and integrated impurity signature analysis identified distinctly different pellet synthesis and processing methods. For example, two different Al, W, and Zr populations in the CMX5-B sample indicated a more complex processing history than the CMX5-A sample. K-edge XANES measurements reveal both metallic and oxide forms of Fe and Ni but with different proportions between each sample. Altogether, these observations suggest multiple sources of impurities, including fabrication (e.g., force-sieving) and feedstock (mineral oxides). This study demonstrates the potential of synchrotron techniques to integrate different signatures across length scales (angstrom to micrometer) to detect and differentiate between contrasting UO 2 fuel fabrication techniques.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

In situ EXAFS study of Sr adsorption on TiO 2 (110) under high ionic strength wastewater conditions

In order to provide important details concerning the adsorption reactions of Sr, batch reactions and a set of both ex situ and in situ Grazing Incidence X-ray Absorption Fine Structure (GIXAFS) adsorption experiments were completed on powdered TiO 2 and on rutile(110), both reacted with either SrCl 2 or SrCO 3 solutions. TiO 2 sorption capacity for strontium (Sr) ranges from 550 ppm (SrCl 2 solutions, second order kinetics) to 1400 ppm (SrCO 3 solutions, first order kinetics), respectively, and is rapid. Sr adsorption decreased as a function of chloride concentration but significantly increased as carbonate concentrations increased. In the presence of carbonate, the ability of TiO 2 to remove Sr from the solution increases by a factor of ~4 due to rapid epitaxial surface precipitation of an SrCO 3 thin film, which registers itself on the rutile(110) surface as a strontianite-like phase (d-spacing 2.8 Å). Extended X-ray Absorption Fine Structure (EXAFS) results suggest the initial attachment is via tetradental inner-sphere Sr adsorption. Moreover, adsorbates from concentrated SrCl 2 solutions contain carbonate and hydroxyl species, which results in both inner- and outer-sphere adsorbates and explains the reduced Sr adsorption in these systems. These results not only provide new insights into Sr kinetics and adsorption on TiO 2 but also provide valuable information concerning potential improvements in effluent water treatment models and are pertinent in developing treatment methods for rutile-coated structural materials within nuclear power plants.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Uranium (VI) Adsorbate Structures on Portlandite [Ca(OH)2] Type Surfaces Determined by Computational Modelling and X-ray Absorption Spectroscopy

Portlandite [Ca(OH) 2 ] is a potentially dominant solid phase in the high pH fluids expected within the cementitious engineered barriers of Geological Disposal Facilities (GDF). This study combined X-ray Absorption Spectroscopy with computational modelling in order to provide atomic-scale data which improves our understanding of how a critically important radionuclide (U) will be adsorbed onto this phase under conditions relevant to a GDF environment. Such data are fundamental for predicting radionuclide mass transfer. Surface coordination chemistry and speciation of uranium with portlandite [Ca(OH) 2 ] under alkaline groundwater conditions (ca. pH 12) were determined by both in situ and ex situ grazing incidence extended X-ray absorption fine structure analysis (EXAFS) and by computational modelling at the atomic level. Free energies of sorption of aqueous uranyl hydroxides, [UO 2 (OH) n ] 2–n (n = 0–5) with the (001), (100) and (203) or (101) surfaces of portlandite are predicted from the potential of mean force using classical molecular umbrella sampling simulation methods and the structural interactions are further explored using fully periodic density functional theory computations. Although uranyl is predicted to only weakly adsorb to the (001) and (100) clean surfaces, there should be significantly stronger interactions with the (203/101) surface or at hydroxyl vacancies, both prevalent under groundwater conditions. The uranyl surface complex is typically found to include four equatorially coordinated hydroxyl ligands, forming an inner-sphere sorbate by direct interaction of a uranyl oxygen with surface calcium ions in both the (001) and (203/101) cases. In contrast, on the (100) surface, uranyl is sorbed with its axis more parallel to the surface plane. The EXAFS data are largely consistent with a surface structural layer or film similar to calcium uranate, but also show distinct uranyl characteristics, with the uranyl ion exhibiting the classic dioxygenyl oxygens at 1.8 Å and between four and five equatorial oxygen atoms at distances between 2.28 and 2.35 Å from the central U absorber. These experimental data are wholly consistent with the adsorbate configuration predicted by the computational models. These findings suggest that, under the strongly alkaline conditions of a cementitious backfill engineered barrier, there would be significant uptake of uranyl by portlandite to inhibit the mobility of U(VI) from the near field of a geological disposal facility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Developing a system for in vivo imaging of maize roots containing iodinated contrast media in soil using synchrotron XCT and XRF

We sought to develop a novel experimental system which enabled application of iodinated contrast media to in vivo plant roots intact in soil and was compatible with time-resolved synchrotron X-ray computed tomography imaging. The system was developed to overcome issues of low contrast to noise within X-ray computed tomography images of plant roots and soil environments, the latter of which can complicate image processing and result in the loss of anatomical information. To demonstrate the efficacy of the system we employ the novel use of both synchrotron X-ray computed tomography and synchrotron X-ray fluorescence mapping to capture the translocation of the contrast media through root vasculature into the leaves. With the application of contrast media we identify fluid flow in root vasculature and visualise anatomical features, which are otherwise often only observable in ex vivo microscopy, including: the xylem, metaxylem, pith, fibres in aerenchyma and leaf venation. We are also able to observe interactions between aerenchyma cross sectional area and solute transport in the root vasculature with depth. Our novel system was capable of successfully delivering sufficient contrast media into root and leaf tissues such that anatomical features could be visualised and internal fluid transport observed. We propose that our system could be used in future to study internal plant transport mechanisms and parameterise models for fluid flow in plants.

59 BASIC BIOLOGICAL SCIENCES↗