Engineering topics

Materials science

Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.

Follow this topic with RSS

At least 559 records · Page 31

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Pultrusion and Vitrimer Composites: Emerging Pathways for Sustainable Structural Materials

Pultrusion is a manufacturing process used to produce fiber-reinforced polymer composites with excellent mechanical, thermal, and chemical properties. The resulting materials are lightweight, durable, and corrosion-resistant, making them valuable in aerospace, automotive, construction, and energy sectors. However, conventional thermoset composites remain difficult to recycle due to their infusible and insoluble cross-linked structure. This review explores integrating vitrimer technology a novel class of recyclable thermosets with dynamic covalent adaptive networks into the pultrusion process. As only limited studies have directly reported vitrimer pultrusion to date, this review provides a forward-looking perspective, highlighting fundamental principles, challenges, and opportunities that can guide future development of recyclable high-performance composites. Vitrimers combine the mechanical strength (tensile strength and modulus) of thermosets with the reprocessability and reshaping of thermoplastics through dynamic bond exchange mechanisms. These polymers offer high-temperature reprocessability, self-healing, and closed-loop recyclability, where recycling efficiency can be evaluated by the recovery yield retention of mechanical properties and reuse cycles meeting the demand for sustainable manufacturing. Key aspects discussed include resin formulation, fiber impregnation, curing cycles, and die design for vitrimer systems. The temperature-dependent bond exchange reactions present challenges in achieving optimal curing and strong fiber–matrix adhesion. Recent studies indicate that vitrimer-based composites can maintain structural integrity while enabling recycling and repair, with mechanical performance such as flexural and tensile strength comparable to conventional composites. Incorporating vitrimer materials into pultrusion could enable high-performance, lightweight products for a circular economy. The remaining challenges include optimizing curing kinetics, improving interfacial adhesion, and scaling production for widespread industrial adoption.

Fiber composites↗

DOE OSTI2020

Influence of Process Parameters and Alloy Composition on Crack Mitigation in Selective Laser Melting

Microcracking and residual stresses are key limitations of laser powder bed fusion (LPBF), an additive manufacturing (AM) technique that uses a high power laser to consolidate successive layers of metal powder. For tungsten, these microcracks find their origin in the combination of a ductile-to-brittle transition (DBT) between 200°C and 400°C and high residual stresses. This work utilized in situ high speed video to capture the cracking mechanisms, and combined the experimental results with thermomechanical modeling to unveil correlations between crack network morphology and process parameter-related variables, such as the local temperature and residual stress distributions. Consequently, preheating and alloying with rare earth oxides were adopted as possible crack mitigation strategies, the efficacy of which was tested against the initial fundamental baseline results. Preheating temperatures above 500°C eliminated all cracking, though this threshold is expected to be higher when tungsten powder (higher oxygen content) is introduced. Alloying can serve as an active oxygen getter in the system, but the rare earth oxides in this work were too large to have significant contributions to crack-mitigation.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Evaluation of Composite Structural Materials for Heliostat Cost Reduction

Structures manufactured from steel comprise up to 40% of a CSP heliostat's cost. Composite structures represent a potential opportunity to reduce this cost. A reference heliostat structural model has been created with a reflector area of 25m 2 . The design, constructed of low-carbon steel, pro-vides baseline deflection and stiffness under a 21 m/s operating wind speeds. Wind loads on the tracker structure are determined for both operating and stow conditions. An established roster of suitable metal alternative materials is considered including: glass, basalt, and carbon reinforced polymer (GFRP, BFRP, and CFRP respectively). Three heliostat components are investigated: the pylon, torque tube, and the purlin-strut assembly. Composite material properties are substituted for those of steel, and the beams are re-sized to match the original steel components' deflection under given wind loads. Weight and cost changes resulting from this resizing are evaluated. It is found that GFRP and BFRP represent a 3X–6X cost premium for the same operating deflection character-istics as steel across all three investigated component classes; with weight reduction only achieved for the purlin-strut assembly. While CFRP components can achieve approximately 25–75% weight savings depending on the application, this comes with a 9X–14X cost increase over the steel base-line for tube-type structures and roughly 5X cost increase when replacing c-channel structures. This work does not rule out the possibility of cost savings when the heliostat design and kinematics to take advantage of composites' specific properties.

14 SOLAR ENERGY↗

NASA NTRSDate not supplied

Multi-Scale Analysis of Effective Mechanical Properties of Porous 3D Woven Composite Materials

This work aims to compute and analyze the mechanical properties of 3D woven composite materials that share the same yarn structure but differ in their matrix porosity and yarn's fiber volume fraction. Assuming linear elastic behavior, NASA's PuMA software was used to characterize the different composites from their constituents' data, averaging their elastic properties in three main directions to obtain their effective orthotropic mechanical properties. This was performed in three steps: firstly, the porous matrix phase was analyzed at the micro-scale; then, these results were used, along with the mechanical properties of the fibers, to model the yarns at the meso-scale; finally, results from the constituents were homogenized and used to model the mechanical behavior of the unit cell at the macro-scale. The 3D woven composite materials selected for this study are made of a mixture of phenolic resin with porosity values between 0 and 0.6, and infiltrated carbon fiber yarns with fiber volume fractions between 0.5 and 0.8. Results from this study show the effect of different matrix porosities and fiber volume fractions on the macro-scale mechanical properties, and were validated through theoretical and semi-empirical expressions found in the literature.

3D woven materials↗

DOE OSTI2023

Understanding oxidation of Fe-Cr-Al alloys through explainable artificial intelligence

Abstract The oxidation resistance of FeCrAl based on alloying composition and oxidizing conditions is predicted using a combinatorial experimental and artificial intelligence approach. A neural network (NN) classification model was trained on the experimental FeCrAl dataset produced at GE Research. Furthermore, using the SHapley Additive exPlanations (SHAP) explainable artificial intelligence (XAI) tool, we explore how the NN can showcase further material insights that are unavailable directly from a black-box model. We report that high Al and Cr content forms protective oxide layer, while Mo in FeCrAl creates thick unprotective oxide scale that is vulnerable to spallation due to thermal expansion. Graphical abstract

Materials Science↗

DOE OSTI2023

Hydrogen and Silicon Effects on Hexagonal Close Packed Fe Alloys at High Pressures: Implications for the Composition of Earth's Inner Core

Hexagonal close-packed (hcp) structured Fe-Ni alloy is believed to be the dominant phase in the Earth's inner core. This phase is expected to contain 4%–5% light elements, such as Si and H. While the effects of individual light element candidates on the equation of state (EoS) of the hcp Fe metal have been studied, their combined effects remain largely unexplored. Here, in this study, we report the equations of state for two hcp-structured Fe-Si-H alloys, namely Fe 0.83 Si 0.17 H 0.07 and Fe 0.83 Si 0.17 H 0.46 , using synchrotron X-ray diffraction measurements up to 125 GPa at 300 K. These alloys were synthesized by cold compression of Fe-9wt%Si in either pure H 2 or Ar-H 2 mixture medium in diamond-anvil cells. The volume increase caused by a H atom in hcp Fe-Si-H alloys is approximately eight times greater than that by a Si atom. We used the improved data set to develop a composition-dependent EoS that covers a wide range of compositions. Our calculated density and bulk sound velocity of hcp Fe-Si-H alloys suggest a large trade-off between Si and H contents in fitting the seismic properties of the inner core. Combining our new EoS with geophysical and geochemical constraints, we propose 1.6–3 wt% Si and 0.15–0.6 wt% H in the Earth's inner core.

58 GEOSCIENCES↗

NASA NTRS1972

Tensile failure criteria for fiber composite materials

The analysis provides insight into the failure mechanics of these materials and defines criteria which serve as tools for preliminary design material selection and for material reliability assessment. The model incorporates both dispersed and propagation type failures and includes the influence of material heterogeneity. The important effects of localized matrix damage and post-failure matrix shear stress transfer are included in the treatment. The model is used to evaluate the influence of key parameters on the failure of several commonly used fiber-matrix systems. Analyses of three possible failure modes were developed. These modes are the fiber break propagation mode, the cumulative group fracture mode, and the weakest link mode. Application of the new model to composite material systems has indicated several results which require attention in the development of reliable structural composites. Prominent among these are the size effect and the influence of fiber strength variability.

Rosen, B. W.↗

NASA NTRS1973

A critical survey of wave propagation and impact in composite materials

A review of the field of stress waves in composite materials is presented covering the period up to December 1972. The major properties of waves in composites are discussed and a summary is made of the major experimental results in this field. Various theoretical models for analysis of wave propagation in laminated, fiber and particle reinforced composites are surveyed. The anisotropic, dispersive and dissipative properties of stress pulses and shock waves in such materials are reviewed. A review of the behavior of composites under impact loading is presented along with the application of wave propagation concepts to the determination of impact stresses in composite plates.

Moon, F. C.↗

NASA NTRS1983

Characterization of composite materials by means of the ultrasonic stress wave factor

The usual approach to nondestructively evaluating a composite structure involves inspection and mechanical analysis of the inspection results. Such an approach has met with only limited success. On the other hand, the ultrasonic stress wave factor technique directly evaluates the material. Despite requiring access to only one surface of the material, the technique interrogates the material in the directions of applied load. Using the stress wave factor technique it is possible to determine the failure location in the material. The correlation of the stress wave factor with stiffness is shown. In addition, the use of the technique for determining the strength or life of composite material structures is discussed.

Duke, J. C., Jr.↗

NASA NTRS1987

Effect of alloy composition on the sodium-sulfate induced hot corrosion attack of cast nickel-base superalloys at 900 C

The effects of Cr, Al, Ti, Mo, Ta, Nb, and W content on the hot corrosion of Ni-base alloys were examined experimentally. The superalloys were tested for 300 1-hr cycles at 900 C in a Mach 0.3 burner rig flame containing 0.5 ppmw sodium. The data reveal that the best corrosion resistance is obtained when the Cr content is greater than 12 percent; however, good resistance is detected in some alloys with Cr content less than 10 percent provided that the Al content is less than 2.5 wt pct and the Ti content is less than 4 wt pct. It is observed that the influence of W, Ta, Mo, and Nb content on resistance is dependent on Al and Ti contents. The derivation of an equation for estimating hot corrosion attack as a function of alloy composition using multiple linear regression analysis is described. The applicability of the equation is tested using various data sets of alloys. It is noted that the equation can be used to explain the effects of alloy composition on attack rates.

Stearns, C. A.↗

NASA NTRS1988

MATE (Materials for Advanced Turbine Engines) Program, Project 3. Volume 2: Design, fabrication and evaluation of an oxide dispersion strengthened sheet alloy combustor liner

The suitability of wrought oxide dispersion strengthened (ODS) superalloy sheet for gas turbine engine combustor applications was evaluated. Two yttria (Y2O3) dispersion strengthened alloys were evaluated; Incoloy MA956 and Haynes Development Alloy (HDA) 8077 (NiCrAl base). Preliminary tests showed both alloys to be potentially viable combustor materials, with neither alloy exhibiting a significant advantage over the other. MA956 was selected as the final alloy based on manufacturing reproducibility for evaluation as a burner liner. A hybrid PW2037 inner burner liner containing MA956 and Hastelloy X components and using a louvered configuration was designed and constructed. The louvered configuration was chosen because of field experience and compatibility with the bill of material PW2037 design. The simulated flight cycle for the ground based engine tests consisted of 4.5 min idle, 1.5 min takeoff and intermediate conditions in a PW2037 engine with average uncorrected combustor exit temperature of 1527 C. Post test evaluation consisting of visual observations and fluorescent penetrant inspections was conducted after 500 cycles of testing. No loss of integrity in the burner liner was shown.

Bose, S.↗

NASA NTRS1989

Strength and toughness of composite materials based on nickel aluminide matrices

Several nickel aluminide matrix composites were prepared using vacuum hot pressing techniques. The matrix compositions, based on Ni3Al, Ni3Al+B, and NiAl, were reinforced with 10 vol pct TiB2 particles. Both smooth- and notched-bend tests were conducted at room temperature on the monolithic as well as the reinforced materials in order to determine the effects of TiB2 reinforcement on both the smooth-bend and notched-bend properties. TiB2 additions were shown to improve the smooth-bend strengths regardless of the matrix composition, while notched-bend tests, conducted to provide estimates of fracture toughness, revealed somewhat lower values for the composites in comparison to the monolithic materials. Fractographic analyses and in situ fracture observations of the composites revealed that preferential fracture in regions of clustered TiB2 particles may significantly affect the measured toughnesses.

Rigney, J. D.↗

NASA NTRS1992

Mechanical response of composite materials with through-the-thickness reinforcement

An experimental investigation was conducted to identify the key geometrical parameters and quantify their influence on the mechanical response of through-the-thickness (TTT) reinforced composite materials. Composite laminates with TTT reinforcement fibers were fabricated using different TTT reinforcement materials and reinforcement methods and laminates were also fabricated of similar construction but without TTT reinforcement fibers. Coupon specimens were machined from these laminates and were destructively tested. TTT reinforcement yarns enhance damage tolerance and improve interlaminar strength. Thick-layer composites with TTT reinforcement yarns have equal or superior mechanical properties to thin-layer composites without TTT reinforcement yarns. A significant potential exists for fabrication cost reduction by using thick-layer composites with TTT reinforcement yarns. Removal of the surface loop of the TTT reinforcement improves compression strength. Stitching provides somewhat higher mechanical properties than integral weaving.

Farley, Gary L.↗

NASA NTRS1994

Physical interpretation and development of ultrasonic nondestructive evaluation techniques applied to the quantitative characterization of textile composite materials

In this Progress Report, we describe our continuing research activities concerning the development and implementation of advanced ultrasonic nondestructive evaluation methods applied to the inspection and characterization of complex composite structures. We explore the feasibility of implementing medical linear array imaging technology as a viable ultrasonic-based nondestructive evaluation method to inspect and characterize complex materials. As an initial step toward the application of linear array imaging technology to the interrogation of a wide range of complex composite structures, we present images obtained using an unmodified medical ultrasonic imaging system of two epoxy-bonded aluminum plate specimens, each with intentionally disbonded regions. These images are compared with corresponding conventional ultrasonic contact transducer measurements in order to assess whether these images can detect disbonded regions and provide information regarding the nature of the disbonded region. We present a description of a standoff/delay fixture which has been designed, constructed, and implemented on a Hewlett-Packard SONOS 1500 medical imaging system. This standoff/delay fixture, when attached to a 7.5 MHz linear array probe, greatly enhances our ability to interrogate flat plate specimens. The final section of this Progress Report describes a woven composite plate specimen that has been specially machined to include intentional flaws. This woven composite specimen will allow us to assess the feasibility of applying linear array imaging technology to the inspection and characterization of complex textile composite materials. We anticipate the results of this on-going investigation may provide a step toward the development of a rapid, real-time, and portable method of ultrasonic inspection and characterization based on linear array technology.

Miller, James G.↗

NASA NTRS1994

Laminated thermoplastic composite material from recycled high density polyethylene

The design of a materials-science, educational experiment is presented. The student should understand the fundamentals of polymer processing and mechanical property testing of materials. The ability to use American Society for Testing and Materials (ASTM) standards is also necessary for designing material test specimens and testing procedures. The objectives of the experiment are (1) to understand the concept of laminated composite materials, processing, testing, and quality assurance of thermoplastic composites and (2) to observe an application example of recycled plastics.

Liu, Ping↗

NASA NTRS1994

Size effect in composite materials and structures: Basic concepts and design considerations

Composite materials display strength characteristics that are similar to those of brittle ceramics, whose strengths are known to decrease with increasing volume for a uniform state of stress (size effect) and also are dependent on stress distribution. These similarities raise the question of whether there is also a size effect in composite materials and structures. There is significant, but inconclusive experimental evidence for the existence of a size effect in composites. Macroscopic and micromechanical statistical models have been developed which predict a size effect and are in general agreement with experimental data. The existence of a significant size effect in composites would be of great importance. For example, it would mean that use of standard test coupons to establish design allowables for large structures could be very nonconservative. Further, it would be necessary to analyze the strength of large composite structures using statistical methods, as is done for ceramics.

Zweben, Carl↗

NASA NTRS1995

Thermographic imaging for high-temperature composite materials: A defect detection study

The ability of a thermographic imaging technique for detecting flat-bottom hole defects of various diameters and depths was evaluated in four composite systems (two types of ceramic matrix composites, one metal matrix composite, and one polymer matrix composite) of interest as high-temperature structural materials. The holes ranged from 1 to 13 mm in diameter and 0.1 to 2.5 mm in depth in samples approximately 2-3 mm thick. The thermographic imaging system utilized a scanning mirror optical system and infrared (IR) focusing lens in conjunction with a mercury cadmium telluride infrared detector element to obtain high resolution infrared images. High intensity flash lamps located on the same side as the infrared camera were used to heat the samples. After heating, up to 30 images were sequentially acquired at 70-150 msec intervals. Limits of detectability based on depth and diameter of the flat-bottom holes were defined for each composite material. Ultrasonic and radiographic images of the samples were obtained and compared with the thermographic images.

Roth, Don J.↗

NASA NTRS1997

Advanced Technology Composite Fuselage - Materials and Processes

The goal of Boeing's Advanced Technology Composite Aircraft Structures (ATCAS) program was to develop the technology required for cost and weight efficient use of composite materials in transport fuselage structure. This contractor report describes results of material and process selection, development, and characterization activities. Carbon fiber reinforced epoxy was chosen for fuselage skins and stiffening elements and for passenger and cargo floor structures. The automated fiber placement (AFP) process was selected for fabrication of monolithic and sandwich skin panels. Circumferential frames and window frames were braided and resin transfer molded (RTM'd). Pultrusion was selected for fabrication of floor beams and constant section stiffening elements. Drape forming was chosen for stringers and other stiffening elements. Significant development efforts were expended on the AFP, braiding, and RTM processes. Sandwich core materials and core edge close-out design concepts were evaluated. Autoclave cure processes were developed for stiffened skin and sandwich structures. The stiffness, strength, notch sensitivity, and bearing/bypass properties of fiber-placed skin materials and braided/RTM'd circumferential frame materials were characterized. The strength and durability of cocured and cobonded joints were evaluated. Impact damage resistance of stiffened skin and sandwich structures typical of fuselage panels was investigated. Fluid penetration and migration mechanisms for sandwich panels were studied.

Scholz, D. B.↗