Search NASA⌕ Search

Engineering topics

Materials science

Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.

Follow this topic with RSS
At least 1,279 records · Page 71
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Environmental exposure effects on composite materials for commercial aircraft

The effects of environmental exposure on composite materials are determined. The environments considered are representative of those experienced by commercial jet aircraft. Initial results have been compiled for the following material systems: T300/5208, T300/5209, and T300/934. Future results will include AS-1/3501-6 and Kevlar 49/F161-188. Specimens are exposed on the exterior and interior of 737 airplanes of three airlines, and to continuous ground-level exposure at four locations. In addition, specimens are exposed in the laboratory to conditions such as: simulated ground-air-ground, weatherometer, and moisture. Residual strength results are presented for specimens exposed for up to five years at five ground-level exposure locations and on airplanes from one airline.

Coggeshall, R. L.↗
NASA NTRS1986

Delamination growth in composite materials

The Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) specimens are employed to characterize MODE I and MODE II interlaminar fracture resistance of graphite/epoxy (CYCOM 982) and graphite/PEEK (APC2) composites. Sizing of test specimen geometries to achieve crack growth in the linear elastic regime is presented. Data reduction schemes based upon beam theory are derived for the ENF specimen and include the effects of shear deformation and friction between crack surfaces on compliance, C, and strain energy release rate, G sub II. Finite element (FE) analyses of the ENF geometry including the contact problem with friction are presented to assess the accuracy of beam theory expressions for C and G sub II. Virtual crack closure techniques verify that the ENF specimen is a pure Mode II test. Beam theory expressions are shown to be conservative by 20 to 40 percent for typical unidirectional test specimen geometries. A FE parametric study investigating the influence of delamination length and depth, span, thickness and material properties on G sub II is presented. Mode I and II interlaminar fracture test results are presented. Important experimental parameters are isolated, such as precracking techniques, rate effects, and nonlinear load-deflection response. It is found that subcritical crack growth and inelastic materials behavior, responsible for the observed nonlinearities, are highly rate-dependent phenomena with high rates generally leading to linear elastic response.

Gillespie, J. W., Jr.↗
NASA NTRS1986

A study of the stress wave factor technique for nondestructive evaluation of composite materials

The acousto-ultrasonic method of nondestructive evaluation is an extremely sensitive means of assessing material response. Efforts continue to complete the understanding of this method. In order to achieve the full sensitivity of the technique, extreme care must be taken in its performance. This report provides an update of the efforts to advance the understanding of this method and to increase its application to the nondestructive evaluation of composite materials. Included are descriptions of a novel optical system that is capable of measuring in-plane and out-of-plane displacements, an IBM PC-based data acquisition system, an extensive data analysis software package, the azimuthal variation of acousto-ultrasonic behavior in graphite/epoxy laminates, and preliminary examination of processing variation in graphite-aluminum tubes.

Sarrafzadeh-Khoee, A.↗
NASA NTRS1985

A normal stress criterion for crack extension direction in orthotropic composite materials

A criterion for predicting the direction of crack extension in orthotropic composite materials is presented. The criterion is based upon the normal stress and the anisotropic tensile strength on arbitrary planes about the tip of a crack. Results are obtained, via finite element solutions, for: (1) isotropic mixed mode fracture, (2) cracks in unidirectional off-axis slotted composite tensile coupons and (3) cracks in cross plied laminates. Comparisons are made with other theories and experimental results.

Buczek, M. B.↗
NASA NTRS1986

Effect of the raw material composition of fabrics on the Limiting Oxygen Index (LOI)

The raw material composition of fabrics is one of the most important factors for LOI value. LOI value was determined in samples of varying composition composed of cellulose, protein, and synthetic fibers and their mixtures, based on ASTM D 2863-76. Cellulose fibers and their mixtures exhibited the lowest value, while synthetic fibers had the highest LOI value.

Jeler, S.↗
NASA NTRS1987

Styrene-terminated polysulfone oligomers as matrix material for graphite reinforced composites: An initial study

Styrene terminated polysulfone oligomers are part of an oligomeric class of compounds with end groups capable of thermal polymerization. These materials can be used as matrices for graphite reinforced composites. The initial evaluation of styrene terminated polysulfone oligomer based composites are summarized in terms of fabrication methods, and mechanical and environmental properties. In addition, a description and evaluation is provided of the NASA/Industry Fellowship Program for Technology Transfer.

Garcia, Dana↗
NASA NTRS1987

Compositional stratigraphy of crustal material from near-infrared spectra

An Earth-based telescopic program to acquire near-infrared spectra of freshly exposed lunar material now contains data for 17 large impact craters with central peaks. Noritic, gabbroic, anorthositic and troctolitic rock types can be distinguished for areas within these large craters from characteristic absorptions in individual spectra of their walls and central peaks. Norites dominate the upper lunar crust while the deeper crustal zones also contain significant amounts of gabbros and anorthosites. Data for material associated with large craters indicate that not only is the lunar crust highly heterogeneous across the nearside, but that the compositional stratigraphy of the lunar crust is nonuniform. Crustal complexity should be expected for other planetary bodies, which should be studied using high spatial and spectral resolution data in and around large impact craters.

Pieters, Carle M.↗
NASA NTRS1987

The effects of crushing speed on the energy-absorption capability of composite material

The energy-absorption capability as a function of crushing speed was determined for Thornel 300/Fiberite 934 (Gr/E) and Kevlar-49/Fiberite 934 (K/E) composite material. Circular cross section tube specimens were crushed at quasi-static, 6 m/sec, and 12 m/sec speeds. Ply orientations of the tube specimens were (0/+ or - theta) sub 2 and (+ or - theta) sub 3 where theta=15, 45, and 75 degress. Based on the results of these tests the energy-absortion capability of Gr/E and K/E was determined to be a function of crushing speed. The crushing modes based on exterior appearance of the crushed tubes were unchanged for either material. However, the interlaminar crushing behavior changed with crushing speed.

Farley, Gary L.↗
NASA NTRS1987

Styrene-terminated polysulfone oligomers as matrix material for graphite reinforced composites - An initial study

Results pertaining to graphite reinforced composites containing styrene-terminated oligomers as the matrix material are summarized. The processing parameters are determined and the properties of the resulting composite are evaluated. In terms of solvent impregnation techniques, CH2Cl2 is the preferred solvent due to its easy removal during the prepreg drying and consolidation steps.

Garcia, Dana↗
NASA NTRS1986

Compositional redistribution during casting of Hg sub 0.8 Cd sub 0.2 Te alloys

A series of Hg(0.8)Cd(0.2)Te ingots was cast both vertically and horizontally under well-defined thermal conditions by using a two-zone furnace with isothermal heat-pipe liners. The main objective of the experiments was to establish correlations between casting parameters and compositional redistribution and to develop ground-based data for a proposed flight experiment of casting of Hg(1-x)Cd(x)Te alloys under reduced gravity conditions. The compositional variations along the axial and radial directions were determined by precision density measurements, infrared transmission spectra, and X-ray energy dispersion spectrometry. Comparison between the experimental results and a numerical simulation of the solidification process of Hg(0.8)Cd(0.2)Te is described.

Su, Ching-Hua↗
NASA NTRS1988

Properties of two composite materials made of toughened epoxy resin and high-strain graphite fiber

Results are presented from an experimental evaluation of IM7/8551-7 and IM6/18081, two new toughened epoxy resin, high strain graphite fiber composite materials. Data include ply-level strengths and moduli, notched tension and compression strengths and compression-after-impact assessments. The measured properties are compared with those of other graphite-epoxy materials.

Dow, Marvin B.↗
NASA NTRS1988

Refractory metal alloys and composites for space power systems

Space power requirements for future NASA and other U.S. missions will range from a few kilowatts to megawatts of electricity. Maximum efficiency is a key goal of any power system in order to minimize weight and size so that the space shuttle may be used a minimum number of times to put the power supply into orbit. Nuclear power has been identified as the primary source to meet these high levels of electrical demand. One way to achieve maximum efficiency is to operate the power supply, energy conversion system, and related components at relatively high temperatures. NASA Lewis Research Center has undertaken a research program on advanced technology of refractory metal alloys and composites that will provide baseline information for space power systems in the 1900's and the 21st century. Basic research on the tensile and creep properties of fibers, matrices, and composites is discussed.

Stephens, Joseph R.↗
NASA NTRS1987

Effect of initial flaw shape on crack extension in orthotropic composite materials

An analytical study is presented showing the effects of the notch tip geometry on the location and direction of crack growth from an existing notch in a unidirectional fibrous composite modelled as a homogeneous, anisotropic, elastic material. Anisotropic elasticity and the normal stress ratio theory are used to study crack growth from elliptical notches in unidirectional composites. Sharp cracks, circular holes, and ellipses are studied under far-field tension and shear loading. Limited comparisons are made showing good correlation with experimental results.

Gurdal, Z.↗
NASA NTRS1988

Response of composite materials to the Space Station orbit environment

The rationale for selecting composite materials with an anodized aluminum foil coating for the Space Station is presented. Data on the effects of the space service environment on these materials are given. Results are also presented on the effect of optical properties of an aluminum/aluminum oxide coating on the thermal balance of the cylindrical structural members. The resistance of this coating to solar ultraviolet degradation is discussed.

Tompkins, S. S.↗
NASA NTRS1987

Errors associated with the use of strain gages on composite materials

The present effort to characterize the influence of strain gage misalignments in the case of their bonding to fiber-reinforced composite materials considers the effects of differences in thermal expansion, transverse sensitivity, and noncoincidence of principal stress on principal strain directions. The largest error is noted to be obtained when the minor Poisson ratio of a composite is measured. The correction procedures remain important for strain measurements on laminates.

Hiel, C. C.↗
NASA NTRS1987

On producing an alloy of uniform composition during rapid solidification processing

The fundamental mechanisms responsible for both micro scale and macro scale compositional variations during cellular and dendritic solidification are discussed. It is shown that presently available models for cellular and dendritic growth in alloys predict only the elimination of macrosegregation during rapid solidification but that microsegregation still persists even in this regime. A simple model is proposed here to describe the complete elimination of microsegregation in the rapid solidification regime. A solid of ideally uniform composition can be produced with no micro or macro segregation at both very low large solidifation rates.

Laxmanan, V.↗
NASA NTRS1988

Compositional redistribution during casting of Hg(0.8)Cd(0.2)Te alloys

A series of Hg(0.8)Cd(0.2)Te ingots was cast both vertically and horizontally under well-defined thermal conditions by using a two-zone furnace with isothermal heat-pipe liners. The main objective of the experiments was to establish correlations between casting parameters and compositional redistribution and to develop ground-based data for a proposed flight experiment of casting of Hg(1-x)Cd(x)Te alloys under reduced gravity conditions. The compositional variations along the axial and radial directions were determined by precision density measurements, infrared transmission spectra, and X-ray energy dispersion spectrometry. Comparison between the experimental results and a numerical simulation of the solidification process of Hg(0.8)Cd(0.2)Te is described.

Su, Ching-Hua↗