Engineering topics
Explore NASA and DOE materials research. Search alloys, composites and material properties, then open the original technical report for test conditions and results.
The objective of this program was to determine the peening stress profiles of rod peened aluminum structural alloys versus shot peened material to define the effective depth of the compressed surface layer.
The paper discusses the effect of cosmic-ray proton interactions with lunar material, the nature and composition of the species resulting from these interactions, and the contribution of these species to the lunar atmosphere. It is shown that hydrogen atoms resulting from cosmic-ray proton neutralization escape into the atmosphere mostly as H2, that only a small fraction of the very small amount of OH and H2O produced by cosmic-ray protons escapes into the atmosphere, and that cosmic-ray protons play a very minor role, as compared with solar-wind protons, in producing lunar atmospheric hydrogen and hydrogenated species. It is concluded that the atmospheric contributions of H2, H, OH, and H2O produced by cosmic-ray protons are about three orders of magnitude less than those due to solar-wind protons.
The use of composite materials for a variety of practical structural applications is presented and the need for an accelerated characterization procedure is assessed. A new experimental and analytical method is presented which allows the prediction of long term properties from short term tests. Some preliminary experimental results are presented.
Tungsten-fiber/FeCrAlY (W/FeCrAlY) was identified as a promising aircraft engine, first generation, turbine blade composite material. Based on available data, W/FeCrAlY should have the stress-rupture, creep, tensile, fatigue, and impact strengths required for turbine blades operating from 1250 to 1370 K. It should also have adequate oxidation, hot corrosion, and thermal cycling damage resistance as well as high thermal conductivity. Concepts for potentially low cost blade fabrication were developed. These concepts were used to design a first stage JT9D convection cooled turbine blade having a calculated 50 K use-temperature advantage over the directionally solidified superalloy blade.
An investigative program is presented in an attempt to add to the current understanding of constraint effects on the response of composite materials under cyclic loading. The objectives were: (1) to use existing data and to develop additional data in order to establish an understanding and quantitative description of flaw growth in unidirectional lamina under cyclic loading at different load direction to fiber direction angles; (2) to establish a similar understanding and description of flaw growth in lamina which are embedded in laminates between other unflawed lamina; (3) to determine the nature of the influence of constraint on flaw growth by quantitatively comparing the results of the tests; and (4) to develop a model and philosophy of constraints effects based on our investigative results.
A review is made of the state-of-the-art in regard to the use of composite materials for reducing the structural mass of automobiles. Reduction of mass provides, in addition to other engineering improvements, increased performance/range advantages that are particularly needed in the electric and hybrid vehicle field. Problems encountered include the attainment of mass production techniques and the prevention of environmental hazards.
This paper reports on an investigation of the concept of modifying the thermal performance of filled polymers through a minor compositional change (presently by coating the filler). The fire-safety of construction materials and the instability of solid rockets are used as examples. A theory is developed which shows that vast improvements are possible by controlling thermal conductivity. Experiments are described that show the weight loss and smoke density in the NBS smoke-density chamber of fiberglass-reinforced epoxy panels, and the instability trends of an AP-HTPB propellant fired in an L-Star rocket motor. The feasibility of tailoring thermal behavior to suit each particular need is demonstrated.
This paper reports the development of two new nondestructive techniques for precise determination of the nature and extent of complex damage and the consequent redistribution of stress in composite materials during quasi-static and cyclic or dynamic loading. The two methods incorporate video-thermography and four-component tensor elastic modulus determination. The experimental and analytical aspects of these two methods are discussed and data is presented.
A program was conducted by NASA with the JT9D engine manufacturer to develop a lightweight, cost effective, composite material fan exit guide vane design having satisfactory structural durability for commerical engine use. Based on the results of a previous company supported program, eight graphite/epoxy and graphite-glass/epoxy guide vane designs were evaluated and four were selected for fabrication and testing. Two commercial fabricators each fabricated 13 vanes. Fatigue tests were used to qualify the selected design configurations under nominally dry, 38 C (100 F) and fully wet and 60 C (140 F) environmental conditions. Cost estimates for a production rate of 1000 vanes per month ranged from 1.7 to 2.6 times the cost of an all aluminum vane. This cost is 50 to 80 percent less than the initial program target cost ratio which was 3 times the cost of an aluminum vane. Application to the JT9D commercial engine is projected to provide a weight savings of 236 N (53 lb) per engine.
User documentation is provided for additional computer programs developed for use in conjunction with SPAR. These programs plot digital data, simplify input for composite material section properties, and compute lamina stresses and strains. Sample problems are presented including execution procedures, program input, and graphical output.
Three test schemes were examined for testing graphite/epoxy (Narmco T300/5208) composite material specimens to failure in compression, including an adaptation of the IITRI "wedge grip" compression fixture, a face-supported-compression fixture, and an end-loaded-coupon fixture. The effects of specimen size, specimen support arrangement and method of load transfer on compressive behavior of graphite/epoxy were investigated. Compressive stress strain, strength, and modulus data obtained with the three fixtures are presented with evaluations showing the effects of all test parameters, including fiber orientation. The IITRI fixture has the potential to provide good stress/strain data to failure for unidirectional and quasi-isotropic laminates. The face supported fixture was found to be the most desirable for testing + or - 45 s laminates.
The influence of hole quality on the structural behavior of composite materials was investigated. From an industry survey it was determined that the most frequent imperfections encountered during hole fabrication are chipout, delamination, and oversize conditions. These hole flaw types were generated in critical areas of static, compression, and fatigue specimens fabricated from T300/5208 graphite/epoxy system. The specimens were tested in static and cyclic pin bearing modes in addition to compression loading. Results of these tests are presented and discussed. The hole chipout defect reduced the static and cyclic endurance characteristics. Oversize holes also lowered the cyclic pin bearing endurance, but had no influence of the static pin bearing characteristics. Delamination had no insignificant influence on the static tension and cyclic pin bearing characteristics. Compression tests demonstrated a deleterious effect for chipout of delamination defects. Hole quality requirements proposed are discussed.
A theoretical model was established to predict the fatigue behavior of composite materials, with emphasis placed on predictions of the degradation of residual strength and residual stiffness during fatigue cycling. The model parameters were evaluated from three test series including static strength fatigue life and residual strength tests. The tests were applied to two graphite/epoxy laminates. Load sequence effects were emphasized for both laminates and the predicted results agreed quite well with subsequent verification tests. Dynamic as well as static stiffness reduction data were collected by use of a PDP11-03 computer, which performed quite satisfactorily and permitted the recording of a substantial amount of dynamic stiffness reduction data.
Numerical and experimental results are presented on the pullout phenomenon in composite materials at a high rate of loading. The finite element method was used, taking into account the existence of a virtual shear deformation layer as the interface between fiber and matrix. Experimental results agree well with those obtained by the finite element method. Numerical results show that the interlaminar shear stress is time dependent, in addition, it is shown to depend on the applied load time history. Under step pulse loading, the interlaminar shear stress fluctuates, finally decaying to its value under static loading.
The accidental release of carbon fibers from civil aircraft and the need for protection of civil aircraft systems from such fibers were studied. It was concluded that the electrical hazard from carbon fibers accidentally released in an aircraft crash fire pose no threat to human life. Overall costs associated with carbon fiber release are predicted to be extremely low. The risk of electrical or electronic failures due to carbon fibers is so minimal that future exploitation of carbon composites in aircraft should be continued. Additional protection of aircraft avionics to guard against carbon fibers is unnecessary. A program to develop alternate materials specifically to overcome the potential electrical hazard is not justified.
Material coupon tests were conducted to formulate design allowables for T300/5208 graphite/epoxy unidirectional tape and bidirectional fabric composites. This paper gives a description of the tests conducted, representative ply level and laminate test data, and results of the statistical analysis. The design allowables for tension and compression strength are given and include the effect of notches, impact damage, temperature extremes and moisture absorption.
It is shown that the effects of constraint on the response of composite materials can be classified as (1) in-plane effects, and (2) through-the-thickness effects; with in-plane constraint being the principal contributor to notched strength and changes in notched strength under quasi-static loading. It is also determined that the constraint situations that produce the greatest static strength do not minimize the extent of damage that develops under either static or cyclic loading, and that through-the-thickness constraint controls the pattern and spacing of transverse cracks in the characteristic damage state that determines those of strength and stress in unnotched laminates. It is concluded that the mode and the extent of damage in notched and unnotched constrained plies is governed by the stress state in those plies, as determined by the constraining ones, and the relationship of stress and strength states.
Three methods for compression testing coupons of filament-reinforced polymer-matrix composite materials are evaluated, to identify the sensitivity of the test techniques to laminate, specimen, and test parameters. A 'wedge-grip' compression fixture, a face-supported compression fixture, and an end-loaded coupon fixture are described. Specimens of 12.5-, 25-, and 50-mm widths, 8-, 16-, and 24-ply thicknesses, and of various fiber orientations were used to test the 'wedge-grip' compression fixture and the face-supported fixture; the end-loaded coupon fixture was tested using 16-ply specimens. Compressive strain-stress, strength, and modulus data obtained with the fixtures and evaluations showing the effects of all the test parameters are presented. One of the conclusions asserts that the 'wedge-grip' compression fixture provides good stress-strain data to failure for unidirectional and quasi-isotropic laminates.