Search NASA⌕ Search

Engineering topics

Propulsion

Explore propulsion reports from NASA NTRS and DOE OSTI. Search rocket engines, electric propulsion and thrusters; verify designs and performance in the source documents.

At least 217 records · Page 12

Launch and Propulsion Systems Materials and Process Development for Rocket Engine Components: Turbomachinery

This presentation identifies the key materials with the highest payoff to advance the state-of-the-art in materials for turbomachinery. Current show stoppers for advancing the state of the art in materials and processes were identified. Technical issues associated with incorporating key materials into new systems are discussed. Opportunities, where they exist, are identified to overcome these technical challenges.

Cannon, James L.↗

Liquid Rocket Propulsion: RS-68 and Linear Aerospike

This paper presents viewgraphs of the RS-68 and Linear Aerospike engines. The topics include: 1) The mission; 2) Design and Development Strategies; 3) Cost Driven Design Trades; 4) Moderate Pressure Requirements Enable Reduced Complexity; 5) Experience Based Design; 6) Development Costs Dominated by Cost of Eliminating Failure Modes; and 7) Reducing Development Costs. This paper also includes the design of the RS-68 Engine and the engine performance.

Murphy, Terry↗

Mars Flyer Rocket Propulsion Risk Assessment Kaiser Marquardt Testing

This report describes the investigation of a 10-N, bipropellant thruster, operating at -40 C, with monomethylhydrazine (MMH) and 25% nitric oxide in nitrogen tetroxide (MON-25). The thruster testing was conducted as part of a risk reduction activity for the Mars Flyer, a proposed mission to fly a miniature airplane in the Martian atmosphere. Testing was conducted using an existing thruster, designed for MMH and MON-3 propellants. The nitric oxide content of MON-3 was increased to 25%, to lower its freezing point to -55 C. The thruster was conditioned, along with the propellants, to temperature prior to hot firing. Thruster operating parameters included oxidizer-to-fuel mixture ratios of 1.6 to 2.7 and inlet pressure ranging from 689 to 2070 kPa. The test matrix consisted of many 10-second firings and several 60-, 300-, 600-, and 1200-second firings, as well as pulse testing. The thruster successfully accumulated nearly 10,000 seconds of operation without failure, at temperatures ranging from -40 C to 22 C. At nominal inlet pressures, the ignition delay was comparable to MMH/MON-3 operation. The optimal performance for the 8.9-N thruster was determined to be at a mixture ratio of 1.93 with an average specific impulse of 298 sec.

Marquardt, Kaiser↗

Mars Flyer Rocket Propulsion Risk Assessment: ARC Testing

This report describes the investigation of a 10-N, bipropellant thruster, operating at -40 C, with monomethy1hydrazine (MMH) and 25% nitric oxide in nitrogen tetroxide (MON-25). The thruster testing was conducted as part of a risk reduction activity for the Mars Flyer, a proposed mission to fly a miniature airplane in the Martian atmosphere. Testing was conducted using an existing thruster, designed for MMH and MON-3 propellants. MON-25 oxidizer was successfully manufactured from MON-3 by the addition of nitric oxide. The thruster was operated successfully over a range of propellant temperatures (-40 to 21 C and feed pressures (6.9 to 20.7 kPa). The thruster hardware was always equal or lower than the propellant temperature. Most tests were 30- and 60-second durations, with 600- and 1200-second duration and pulse testing also conducted. When operating at -40 C, the mixture ratio of the thruster shifted from the nominal value of 1.65 to about 1.85, probably caused by an increase in MMH viscosity, with a corresponding reduction in MMH flowrate. Specific impulse at - 40 C (at nominal feed pressures) was 267 sec, while performance was 277 sec at 21 C. This difference in performance was due, in part, to the mixture ratio shift.

Source record↗

Fabrication and Testing of Ceramic Matrix Composite Rocket Propulsion Components

NASA has established goals for Second and Third Generation Reusable Launch Vehicles. Emphasis has been placed on significantly improving safety and decreasing the cost of transporting payloads to orbit. Ceramic matrix composites (CMC) components are being developed by NASA to enable significant increases in safety and engineer performance, while reducing costs. The development of the following CMC components are being pursued by NASA: (1) Simplex CMC Blisk; (2) Cooled CMC Nozzle Ramps; (3) Cooled CMC Thrust Chambers; and (4) CMC Gas Generator. These development efforts are application oriented, but have a strong underpinning of fundamental understanding of processing-microstructure-property relationships relative to structural analyses, nondestructive characterization, and material behavior analysis at the coupon and component and system operation levels. As each effort matures, emphasis will be placed on optimizing and demonstrating material/component durability, ideally using a combined Building Block Approach and Build and Bust Approach.

Effinger, M. R.↗

A Global Optimization Methodology for Rocket Propulsion Applications

While the response surface method is an effective method in engineering optimization, its accuracy is often affected by the use of limited amount of data points for model construction. In this chapter, the issues related to the accuracy of the RS approximations and possible ways of improving the RS model using appropriate treatments, including the iteratively re-weighted least square (IRLS) technique and the radial-basis neural networks, are investigated. A main interest is to identify ways to offer added capabilities for the RS method to be able to at least selectively improve the accuracy in regions of importance. An example is to target the high efficiency region of a fluid machinery design space so that the predictive power of the RS can be maximized when it matters most. Analytical models based on polynomials, with controlled level of noise, are used to assess the performance of these techniques.

Source record↗

Rocket Propulsion Testing at NASA's John C. Stennis Space Center

Viewgraph presentation on the design and testing Liquid Hydrogen Barge Vaporizers at NASA John C. Stennis Space Center is shown. The topics include: 1) Vaporizer Requirements; 2) Vaporizer Design; 3) LH2 # 2 Vaporizer Statistics; 4) Corrective Actions; and 5) Lessons Learned.

Schwer, Robert↗

Remembering the Giants: Apollo Rocket Propulsion Development

Topics discussed include: Rocketdyne - F-1 Saturn V First Stage Engine; Rocketdyne - J-2 Saturn V 2nd & 3rd Stage Engine; Rocketdyne - SE-7 & SE-8 Engines; Aerojet - AJ10-137 Apollo Service Module Engine; Aerojet - Attitude Control Engines; TRW - Lunar Descent Engine; and Rocketdyne - Lunar Ascent Engine.

Fisher, Steven C.↗

National Institute for Rocket Propulsion Systems (NIRPS)

NIRPS is a responsive solution to the current needs of Nation and the direction of the National Space Policy NIRPS will leverage the capabilities of the entire industry NIRPS is a distributed and low-cost solution for NASA and other Government Departments & Agencies

Thomas, Dale↗