Engineering topics

Propulsion

Explore propulsion reports from NASA NTRS and DOE OSTI. Search rocket engines, electric propulsion and thrusters; verify designs and performance in the source documents.

Follow this topic with RSS

At least 1,747 records · Page 97

All sources NASA NTRS DOE OSTI

NASA NTRS2011

Waterhammer Transient Simulation and Model Anchoring for the Robotic Lunar Lander Propulsion System

Waterhammer transients have the potential to adversely impact propulsion system design if not properly addressed. Waterhammer can potentially lead to system plumbing, and component damage. Multi-thruster propulsion systems also develop constructive/destructive wave interference which becomes difficult to predict without detailed models. Therefore, it is important to sufficiently characterize propulsion system waterhammer in order to develop a robust design with minimal impact to other systems. A risk reduction activity was performed at Marshall Space Flight Center to develop a tool for estimating waterhammer through the use of anchored simulation for the Robotic Lunar Lander (RLL) propulsion system design. Testing was performed to simulate waterhammer surges due to rapid valve closure and consisted of twenty-two series of waterhammer tests, resulting in more than 300 valve actuations. These tests were performed using different valve actuation schemes and three system pressures. Data from the valve characterization tests were used to anchor the models that employed MSCSoftware.EASY5 v.2010 to model transient fluid phenomena by using transient forms of mass and energy conservation. The anchoring process was performed by comparing initial model results to experimental data and then iterating the model input to match the simulation results with the experimental data. The models provide good correlation with experimental results, supporting the use of EASY5 as a tool to model fluid transients and provide a baseline for future RLL system modeling. This paper addresses tasks performed during the waterhammer risk reduction activity for the RLL propulsion system. The problem of waterhammer simulation anchoring as applied to the RLL system is discussed with results from the corresponding experimental valve tests. Important factors for waterhammer mitigation are discussed along with potential design impacts to the RLL propulsion system.

Stein, William B.↗

NASA NTRS2011

Catalytic Microtube Rocket Igniter

Devices that generate both high energy and high temperature are required to ignite reliably the propellant mixtures in combustion chambers like those present in rockets and other combustion systems. This catalytic microtube rocket igniter generates these conditions with a small, catalysis-based torch. While traditional spark plug systems can require anywhere from 50 W to multiple kW of power in different applications, this system has demonstrated ignition at less than 25 W. Reactants are fed to the igniter from the same tanks that feed the reactants to the rest of the rocket or combustion system. While this specific igniter was originally designed for liquid methane and liquid oxygen rockets, it can be easily operated with gaseous propellants or modified for hydrogen use in commercial combustion devices. For the present cryogenic propellant rocket case, the main propellant tanks liquid oxygen and liquid methane, respectively are regulated and split into different systems for the individual stages of the rocket and igniter. As the catalyst requires a gas phase for reaction, either the stored boil-off of the tanks can be used directly or one stream each of fuel and oxidizer can go through a heat exchanger/vaporizer that turns the liquid propellants into a gaseous form. For commercial applications, where the reactants are stored as gases, the system is simplified. The resulting gas-phase streams of fuel and oxidizer are then further divided for the individual components of the igniter. One stream each of the fuel and oxidizer is introduced to a mixing bottle/apparatus where they are mixed to a fuel-rich composition with an O/F mass-based mixture ratio of under 1.0. This premixed flow then feeds into the catalytic microtube device. The total flow is on the order of 0.01 g/s. The microtube device is composed of a pair of sub-millimeter diameter platinum tubes connected only at the outlet so that the two outlet flows are parallel to each other. The tubes are each approximately 10 cm long and are heated via direct electric resistive heating. This heating brings the gasses to their minimum required ignition temperature, which is lower than the auto-thermal ignition temperature, and causes the onset of both surface and gas phase ignition producing hot temperatures and a highly reacting flame. The combustion products from the catalytic tubes, which are below the melting point of platinum, are injected into the center of another combustion stage, called the primary augmenter. The reactants for this combustion stage come from the same source but the flows of non-premixed methane and oxygen gas are split off to a secondary mixing apparatus and can be mixed in a near-stoichiometric to highly lean mixture ratio. The primary augmenter is a component that has channels venting this mixed gas to impinge on each other in the center of the augmenter, perpendicular to the flow from the catalyst. The total crosssectional area of these channels is on a similar order as that of the catalyst. The augmenter has internal channels that act as a manifold to distribute equally the gas to the inward-venting channels. This stage creates a stable flame kernel as its flows, which are on the order of 0.01 g/s, are ignited by the combustion products of the catalyst. This stage is designed to produce combustion products in the flame kernel that exceed the autothermal ignition temperature of oxygen and methane.

Schneider, Steven J.↗

NASA NTRS2012

Roadmap for In-Space Propulsion Technology

NASA has created a roadmap for the development of advanced in-space propulsion technologies for the NASA Office of the Chief Technologist (OCT). This roadmap was drafted by a team of subject matter experts from within the Agency and then independently evaluated, integrated and prioritized by a National Research Council (NRC) panel. The roadmap describes a portfolio of in-space propulsion technologies that could meet future space science and exploration needs, and shows their traceability to potential future missions. Mission applications range from small satellites and robotic deep space exploration to space stations and human missions to Mars. Development of technologies within the area of in-space propulsion will result in technical solutions with improvements in thrust, specific impulse (Isp), power, specific mass (or specific power), volume, system mass, system complexity, operational complexity, commonality with other spacecraft systems, manufacturability, durability, and of course, cost. These types of improvements will yield decreased transit times, increased payload mass, safer spacecraft, and decreased costs. In some instances, development of technologies within this area will result in mission-enabling breakthroughs that will revolutionize space exploration. There is no single propulsion technology that will benefit all missions or mission types. The requirements for in-space propulsion vary widely according to their intended application. This paper provides an updated summary of the In-Space Propulsion Systems technology area roadmap incorporating the recommendations of the NRC.

Meyer, Michael↗

NASA NTRS2012

Mars Sample Return Using Solar Sail Propulsion

Many Mars Sample Return (MSR) architecture studies have been conducted over the years. A key element of them is the Earth Return Stage (ERS) whose objective is to obtain the sample from the Mars Ascent Vehicle (MAV) and return it safely to the surface of the Earth. ERS designs predominantly use chemical propulsion [1], incurring a significant launch mass penalty due to the low specific impulse of such systems coupled with the launch mass sensitivity to returned mass. It is proposed to use solar sail propulsion for the ERS, providing a high (effective) specific impulse propulsion system in the final stage of the multi-stage system. By doing so to the launch mass of the orbiter mission can be significantly reduced and hence potentially decreasing mission cost. Further, solar sailing offers a unique set of non-Keplerian low thrust trajectories that may enable modifications to the current approach to designing the Earth Entry Vehicle by potentially reducing the Earth arrival velocity. This modification will further decrease the mass of the orbiter system. Solar sail propulsion uses sunlight to propel vehicles through space by reflecting solar photons from a large, mirror-like surface made of a lightweight, reflective material. The continuous photonic pressure provides propellantless thrust to conduct orbital maneuvering and plane changes more efficiently than conventional chemical propulsion. Because the Sun supplies the necessary propulsive energy, solar sails require no onboard propellant, thus reducing system mass. This technology is currently at TRL 7/8 as demonstrated by the 2010 flight of the Japanese Aerospace Exploration Agency, JAXA, IKAROS mission. [2]

Johnson, Les↗

NASA NTRS2013

Assessment of tbe Performance of Ablative Insulators Under Realistic Solid Rocket Motor Operating Conditions (a Doctoral Dissertation)

Ablative insulators are used in the interior surfaces of solid rocket motors to prevent the mechanical structure of the rocket from failing due to intense heating by the high-temperature solid-propellant combustion products. The complexity of the ablation process underscores the need for ablative material response data procured from a realistic solid rocket motor environment, where all of the potential contributions to material degradation are present and in their appropriate proportions. For this purpose, the present study examines ablative material behavior in a laboratory-scale solid rocket motor. The test apparatus includes a planar, two-dimensional flow channel in which flat ablative material samples are installed downstream of an aluminized solid propellant grain and imaged via real-time X-ray radiography. In this way, the in-situ transient thermal response of an ablator to all of the thermal, chemical, and mechanical erosion mechanisms present in a solid rocket environment can be observed and recorded. The ablative material is instrumented with multiple micro-thermocouples, so that in-depth temperature histories are known. Both total heat flux and thermal radiation flux gauges have been designed, fabricated, and tested to characterize the thermal environment to which the ablative material samples are exposed. These tests not only allow different ablative materials to be compared in a realistic solid rocket motor environment but also improve the understanding of the mechanisms that influence the erosion behavior of a given ablative material.

Martin, Heath Thomas↗

NASA NTRS2013

Benefits of Hybrid-Electric Propulsion to Achieve 4x Increase in Cruise Efficiency for a VTOL Aircraft

Electric propulsion enables radical new vehicle concepts, particularly for Vertical Takeoff and Landing (VTOL) aircraft because of their significant mismatch between takeoff and cruise power conditions. However, electric propulsion does not merely provide the ability to normalize the power required across the phases of flight, in the way that automobiles also use hybrid electric technologies. The ability to distribute the thrust across the airframe, without mechanical complexity and with a scale-free propulsion system, is a new degree of freedom for aircraft designers. Electric propulsion is scale-free in terms of being able to achieve highly similar levels of motor power to weight and efficiency across a dramatic scaling range. Applying these combined principles of electric propulsion across a VTOL aircraft permits an improvement in aerodynamic efficiency that is approximately four times the state of the art of conventional helicopter configurations. Helicopters typically achieve a lift to drag ratio (L/D) of between 4 and 5, while the VTOL aircraft designed and developed in this research were designed to achieve an L/D of approximately 20. Fundamentally, the ability to eliminate the problem of advancing and retreating rotor blades is shown, without resorting to unacceptable prior solutions such as tail-sitters. This combination of concept and technology also enables a four times increase in range and endurance while maintaining the full VTOL and hover capability provided by a helicopter. Also important is the ability to achieve low disc-loading for low ground impingement velocities, low noise and hover power minimization (thus reducing energy consumption in VTOL phases). This combination of low noise and electric propulsion (i.e. zero emissions) will produce a much more community-friendly class of vehicles. This research provides a review of the concept brainstorming, configuration aerodynamic and mission analysis, as well as subscale prototype construction and flight testing that verifies transition flight control. A final down-selected vehicle is also presented.

Fredericks, William J.↗

NASA NTRS2013

Revolutionary Aeropropulsion Concept for Sustainable Aviation: Turboelectric Distributed Propulsion

In response to growing aviation demands and concerns about the environment and energy usage, a team at NASA proposed and examined a revolutionary aeropropulsion concept, a turboelectric distributed propulsion system, which employs multiple electric motor-driven propulsors that are distributed on a large transport vehicle. The power to drive these electric propulsors is generated by separately located gas-turbine-driven electric generators on the airframe. This arrangement enables the use of many small-distributed propulsors, allowing a very high effective bypass ratio, while retaining the superior efficiency of large core engines, which are physically separated but connected to the propulsors through electric power lines. Because of the physical separation of propulsors from power generating devices, a new class of vehicles with unprecedented performance employing such revolutionary propulsion system is possible in vehicle design. One such vehicle currently being investigated by NASA is called the "N3-X" that uses a hybrid-wing-body for an airframe and superconducting generators, motors, and transmission lines for its propulsion system. On the N3-X these new degrees of design freedom are used (1) to place two large turboshaft engines driving generators in freestream conditions to minimize total pressure losses and (2) to embed a broad continuous array of 14 motor-driven fans on the upper surface of the aircraft near the trailing edge of the hybrid-wing-body airframe to maximize propulsive efficiency by ingesting thick airframe boundary layer flow. Through a system analysis in engine cycle and weight estimation, it was determined that the N3-X would be able to achieve a reduction of 70% or 72% (depending on the cooling system) in energy usage relative to the reference aircraft, a Boeing 777-200LR. Since the high-power electric system is used in its propulsion system, a study of the electric power distribution system was performed to identify critical dynamic and safety issues. This paper presents some of the features and issues associated with the turboelectric distributed propulsion system and summarizes the recent study results, including the high electric power distribution, in the analysis of the N3-X vehicle.

Kim, Hyun Dae↗

NASA NTRS2014

RS-34 Phoenix In-Space Propulsion System Applied to Active Debris Removal Mission

In-space propulsion is a high percentage of the cost when considering Active Debris Removal mission. For this reason it is desired to research if existing designs with slight modification would meet mission requirements to aid in reducing cost of the overall mission. Such a system capable of rendezvous, close proximity operations, and de-orbit of Envisat class resident space objects has been identified in the existing RS-34 Phoenix. RS-34 propulsion system is a remaining asset from the de-commissioned United States Air Force Peacekeeper program; specifically the pressure-fed storable bi-propellant Stage IV Post Boost Propulsion System. The National Aeronautics and Space Administration (NASA) Marshall Space Flight Center (MSFC) gained experience with the RS-34 propulsion system on the successful Ares I-X flight test program flown in the Ares I-X Roll control system (RoCS). The heritage hardware proved extremely robust and reliable and sparked interest for further utilization on other potential in-space applications. Subsequently, MSFC has obtained permission from the USAF to obtain all the remaining RS-34 stages for re-use opportunities. The MSFC Advanced Concepts Office (ACO) was commissioned to lead a study for evaluation of the Rocketdyne produced RS-34 propulsion system as it applies to an active debris removal design reference mission for resident space object targets including Envisat. Originally designed, the RS-34 Phoenix provided in-space six-degrees-of freedom operational maneuvering to deploy payloads at multiple orbital locations. The RS-34 Concept Study lead by sought to further understand application for a similar orbital debris design reference mission to provide propulsive capability for rendezvous, close proximity operations to support the capture phase of the mission, and deorbit of single or multiple large class resident space objects. Multiple configurations varying the degree of modification were identified to trade for dry mass optimization and propellant load. The results of the RS-34 Phoenix Concept Study show that the system is technically sufficient to successfully support all of the missions to rendezvous, capture, and de-orbit targets including Envisat and Hubble Space Telescope. The results and benefits of the RS-34 Orbital Debris Application Concept Study are presented in this paper.

Esther, Elizabeth A.↗

NASA NTRS2014

The Nuclear Cryogenic Propulsion Stage

The fundamental capability of Nuclear Thermal Propulsion (NTP) is game changing for space exploration. A first generation Nuclear Cryogenic Propulsion Stage (NCPS) based on NTP could provide high thrust at a specific impulse above 900 s, roughly double that of state of the art chemical engines. Characteristics of fission and NTP indicate that useful first generation systems will provide a foundation for future systems with extremely high performance. The role of the NCPS in the development of advanced nuclear propulsion systems could be analogous to the role of the DC-3 in the development of advanced aviation. Progress made under the NCPS project could help enable both advanced NTP and advanced Nuclear Electric Propulsion (NEP). Nuclear propulsion can be affordable and viable compared to other propulsion systems and must overcome a biased public fear due to hyper-environmentalism and a false perception of radiation and explosion risk.

Houts, Michael G.↗

NASA NTRS2015

Resource Prospector Propulsion System Cold Flow Testing

Resource Prospector (RP) is a NASA mission being led by NASA Ames Research Center with current plans to deliver a scientific payload package aboard a rover to the lunar surface. As part of an early risk reduction activity, Marshall Space Flight Center (MSFC) and Johnson Space Flight Center (JSC) have jointly developed a government-version concept of a lunar lander for the mission. The spacecraft consists of two parts, the lander and the rover which carries the scientific instruments. The lander holds the rover during launch, cruise, and landing on the surface. Following terminal descent and landing the lander portion of the spacecraft become dormant after the rover embarks on the science mission. The lander will be equipped with a propulsion system for lunar descent and landing, as well as trajectory correction and attitude control maneuvers during transit to the moon. Hypergolic propellants monomethyl hydrazine and nitrogen tetroxide will be used to fuel sixteen 70-lbf descent thrusters and twelve 5-lbf attitude control thrusters. A total of four metal-diaphragm tanks, two per propellant, will be used along with a high-pressure composite-overwrapped pressure vessel for the helium pressurant gas. Many of the major propulsion system components are heritage missile hardware obtained by NASA from the Air Force. In parallel with the flight system design activities, a simulated propulsion system based on flight drawings was built for conducting a series of water flow tests to characterize the transient fluid flow of the propulsion system feed lines and to verify the critical operation modes such as system priming, waterhammer, and crucial mission duty cycles. The primary objective of the cold flow testing was to simulate the RP propulsion system fluid flow operation through water flow testing and to obtain data for anchoring analytical models. The models will be used to predict the transient and steady state flow behaviors in the actual flight operations. All design and build efforts, including the analytical modeling, have been performed. The cold flow testing of the propulsion system was set up and conducted at a NASA MSFC test facility. All testing was completed in the summer of 2014, and this paper documents the results of that testing and the associated fluid system modeling efforts.

Williams, Hunter↗

NASA NTRS2016

Foundational Methane Propulsion Related Technology Efforts, and Challenges for Applications to Human Exploration Beyond Earth Orbit

Current interest in human exploration beyond earth orbit is driving requirements for high performance, long duration space transportation capabilities. Continued advancement in photovoltaic power systems and investments in high performance electric propulsion promise to enable solar electric options for cargo delivery and pre-deployment of operational architecture elements. However, higher thrust options are required for human in-space transportation as well as planetary descent and ascent functions. While high thrust requirements for interplanetary transportation may be provided by chemical or nuclear thermal propulsion systems, planetary descent and ascent systems are limited to chemical solutions due to their higher thrust to weight and potential planetary protection concerns. Liquid hydrogen fueled systems provide high specific impulse, but pose challenges due to low propellant density and the thermal issues of long term propellant storage. Liquid methane fueled propulsion is a promising compromise with lower specific impulse, higher bulk propellant density and compatibility with proposed in-situ propellant production concepts. Additionally, some architecture studies have identified the potential for commonality between interplanetary and descent/ascent propulsion solutions using liquid methane (LCH4) and liquid oxygen (LOX) propellants. These commonalities may lead to reduced overall development costs and more affordable exploration architectures. With this increased interest, it is critical to understand the current state of LOX/LCH4 propulsion technology and the remaining challenges to its application to beyond earth orbit human exploration. This paper provides a survey of NASA's past and current methane propulsion related technology efforts, assesses the accomplishments to date, and examines the remaining risks associated with full scale development.

Brown, Thomas↗

NASA NTRS2016

Additive Manufacturing for Affordable Rocket Engines

Additive manufacturing (also known as 3D printing) technology has the potential to drastically reduce costs and lead times associated with the development of complex liquid rocket engine systems. NASA is using 3D printing to manufacture rocket engine components including augmented spark igniters, injectors, turbopumps, and valves. NASA is advancing the process to certify these components for flight. Success Story: MSFC has been developing rocket 3D-printing technology using the Selective Laser Melting (SLM) process. Over the last several years, NASA has built and tested several injectors and combustion chambers. Recently, MSFC has 3D printed an augmented spark igniter for potential use the RS-25 engines that will be used on the Space Launch System. The new design is expected to reduce the cost of the igniter by a factor of four. MSFC has also 3D printed and tested a liquid hydrogen turbopump for potential use on an Upper Stage Engine. Additive manufacturing of the turbopump resulted in a 45% part count reduction. To understanding how the 3D printed parts perform and to certify them for flight, MSFC built a breadboard liquid rocket engine using additive manufactured components including injectors, turbomachinery, and valves. The liquid rocket engine was tested seven times in 2016 using liquid oxygen and liquid hydrogen. In addition to exposing the hardware to harsh environments, engineers learned to design for the new manufacturing technique, taking advantage of its capabilities and gaining awareness of its limitations. Benefit: The 3D-printing technology promises reduced cost and schedule for rocket engines. Cost is a function of complexity, and the most complicated features provide the largest opportunities for cost reductions. This is especially true where brazes or welds can be eliminated. The drastic reduction in part count achievable with 3D printing creates a waterfall effect that reduces the number of processes and drawings, decreases the amount of touch labor required, and increases reliability. When certification is achieved, NASA missions will be able to realize these benefits.

West, Brian↗

NASA NTRS2017

Revisiting Nuclear Thermal Propulsion for Human Mars Exploration

Nuclear Thermal Propulsion (NTP) has long been considered as a viable in-space transportation alternative for delivering crew and cargo to the Martian system. While technology development work in nuclear propulsion has continued over the year, general interest in NTP propulsion applications has historically been tied directly to the ebb and flow of interest in sending humans to explore Mars. As far back as the 1960’s, plans for NTP-based human Mars exploration have been proposed and periodically revisited having most recently been considered as part of NASA Design Reference Architecture (DRA) 5.0. NASA has been investigating human Mars exploration strategies tied to its current Journey to Mars for the past few years however, NTP has only recently been added into the set of alternatives under consideration for in-space propulsion under the Mars Study Capability (MSC) team, formerly the Evolvable Mars Campaign (EMC) team. The original charter of the EMC was to find viable human Mars exploration approaches that relied heavily on technology investment work already underway, specifically related to the development of large Solar Electric Propulsion (SEP) systems. The EMC team baselined several departures from traditional Mars exploration ground rules to enable these types of architectures. These ground rule changes included lower energy conjunction class trajectories with corresponding longer flight times, aggregation of mission elements in cis-Lunar space rather than Low Earth Orbit (LEO) and, in some cases, the pre-deployment of Earth return propulsion systems to Mars. As the MSC team continues to refine the in-space transportation trades, an NTP-based architecture that takes advantage of some of these ground rule departures is being introduced.

Percy, Thomas K.↗

NASA NTRS2017

Overview of the Development of the Advanced Electric Propulsion System (AEPS)

NASA is committed to the demonstration and application of high-power solar electric propulsion to meet its future mission needs. It is continuing to develop the 14 kW Advanced Electric Propulsion System (AEPS) under a project that recently completed an Early Integrated System Test (EIST) and System Preliminary Design Review (PDR). In addition, NASA is pursuing external partnerships in order to demonstrate Solar Electric Propulsion (SEP) technology and the advantages of high-power electric propulsion-based spacecraft. The recent announcement of a Power and Propulsion Element (PPE) as the first major piece of an evolvable human architecture to Mars has replaced the Asteroid Redirect Robotic Mission (ARRM) as the most likely first application of the AEPS Hall thruster system. This high-power SEP capability, or an extensible derivative of it, has been recognized as a critical part of a new, affordable human exploration architecture for missions beyond-low-Earth-orbit. This paper presents the status of AEPS development activities, and describes how AEPS hardware will be integrated into the PPE ion propulsion system.

Herman, Daniel↗

NASA NTRS2018

Iodine Hall-Effect Electric Propulsion System Research, Development, and System Durability Demonstration

This paper reviews recent iodine electric propulsion research and development activities at the NASA Glenn Research Center (GRC). Activities included (i) investigation of the iodine compatibility of BaO-CaO-Al2O3 impregnated tungsten hollow cathodes based on a flight heritage design, (ii) investigation of the iodine compatibility of a handful of materials common to propulsion systems, spacecraft, and ground test facilities, (iii) development of reliable iodine feed system technologies, (iv) implementation of test facility improvements in an attempt to mitigate iodine associated negative impacts, and culminated in (v) an 1,174-hour hybrid iodine-xenon propulsion system durability demonstration (iodine fed Hall-effect thruster with xenon fed cathode). Each of the activities resulted in extensive insights that shall inform future iodine electric propulsion developments. While reliable operation of a BaO-CaO-Al2O3 impregnated tungsten hollow cathode on iodine vapor was not achieved, long-term operation on xenon gas in proximity to an iodine fed thruster was demonstrated without any measurable degradation or cross-contamination of the cathode. Furthermore, iodine material corrosion investigations conducted at 300degC over 5, 15, and 30 days showed significant deterioration of all materials evaluated, although the same materials with a silicon coating proved nearly impervious to iodine so long as the coating was not mechanically damaged. Finally, the 1,174-hour durability test demonstration showed that (i) iodine feed system technologies developed at GRC delivered well-regulated uninterrupted propellant, (ii) implementation of appropriate facility improvements and procedures can limit negative impacts of iodine on test hardware and ground support equipment, although facility challenges with iodine are extensive, and (iii) a Hall-effect thruster operates with similar performance whether employing iodine or xenon propellant over long durations. The work was motivated by strong government and commercial interest in the growing capabilities of small-spacecraft (<500 kg), in combination with interest for denser low-power, high delta-v in-space propulsion systems. This work adds to a growing body of research and development efforts aimed at addressing the many anticipated challenges of implementing iodine as an in-space propellant. This work was conducted under the Advanced In-Space Propulsion (AISP) project funded through the Game Changing Development (GCD) program within NASA's Science Technology Mission Directorate (STMD).

Benavides, Gabriel F.↗

NASA NTRS2018

Iodine Hall-Effect Electric Propulsion System Research, Development, and System Durability Demonstration

This paper reviews recent iodine electric propulsion research and development activities at the NASA Glenn Research Center (GRC). Activities included (i) investigation of the iodine compatibility of BaO-CaO-Al2O3 impregnated tungsten hollow cathodes based on a flight heritage design, (ii) investigation of the iodine compatibility of a handful of materials common to propulsion systems, spacecraft, and ground test facilities, (iii) development of reliable iodine feed system technologies, (iv) implementation of test facility improvements in an attempt to mitigate iodine associated negative impacts, and culminated in (v) an 1,174-hour hybrid iodine-xenon propulsion system durability demonstration (iodine fed Hall-effect thruster with xenon fed cathode). Each of the activities resulted in extensive insights that shall inform future iodine electric propulsion developments. While reliable operation of a BaO-CaO-Al2O3 impregnated tungsten hollow cathode on iodine vapor was not achieved, long-term operation on xenon gas in proximity to an iodine fed thruster was demonstrated without any measurable degradation or cross-contamination of the cathode. Furthermore, iodine material corrosion investigations conducted at 300 C over 5, 15, and 30 days showed significant deterioration of all materials evaluated, although the same materials with a silicon coating proved nearly impervious to iodine so long as the coating was not mechanically damaged. Finally, the 1,174-hour durability test demonstration showed that (i) iodine feed system technologies developed at GRC delivered well-regulated uninterrupted propellant, (ii) implementation of appropriate facility improvements and procedures can limit negative impacts of iodine on test hardware and ground support equipment, although facility challenges with iodine are extensive, and (iii) a Hall-effect thruster operates with similar performance whether employing iodine or xenon propellant over long durations. The work was motivated by strong government and commercial interest in the growing capabilities of small-spacecraft (<500 kg), in combination with interest for denser low-power, high delta-v in-space propulsion systems. This work adds to a growing body of research and development efforts aimed at addressing the many anticipated challenges of implementing iodine as an in-space propellant. This work was conducted under the Advanced In-Space Propulsion (AISP) project funded through the Game Changing Development (GCD) program within NASA's Science Technology Mission Directorate (STMD).

Benavides, Gabriel F.↗

NASA NTRS2018

Iodine Hall-Effect Electric Propulsion System Research, Development, and System Durability Demonstration

This paper reviews recent iodine electric propulsion research and development activities at the NASA Glenn Research Center (GRC). Activities included (i) investigation of the iodine compatibility of BaO-CaO-Al2O3 impregnated tungsten hollow cathodes based on a flight heritage design, (ii) investigation of the iodine compatibility of a handful of materials common to propulsion systems, spacecraft, and ground test facilities, (iii) development of reliable iodine feed system technologies, (iv) implementation of test facility improvements in an attempt to mitigate iodine associated negative impacts, and culminated in (v) an 1,174-hour hybrid iodine-xenon propulsion system durability demonstration (iodine fed Hall-effect thruster with xenon fed cathode). Each of the activities resulted in extensive insights that shall informfuture iodine electric propulsion developments. While reliable operation of a BaO-CaO-Al2O3 impregnated tungsten hollow cathode on iodine vapor was not achieved, long-term operation on xenon gas in proximity to an iodine fed thruster was demonstrated without any measurable degradation or cross-contamination of the cathode. Furthermore, iodine material corrosion investigations conducted at 300 degrees C over 5, 15, and 30 days showed significant deterioration of all materials evaluated, although the same materials with a silicon coating proved nearly impervious to iodine so long as the coating was not mechanically damaged. Finally, the 1,174-hour durability test demonstration showed that (i) iodine feed system technologies developed at GRC delivered well-regulated uninterrupted propellant, (ii) implementation of appropriate facility improvements and procedures can limit negative impacts of iodine on test hardware and ground support equipment, although facility challenges with iodine are extensive, and (iii) a Hall-effect thruster operates with similar performance whether employing iodine or xenon propellant over long durations. The work was motivated by strong government and commercial interest in the growing capabilities of small-spacecraft (<500 kg), in combination with interest for denser low-power, high delta-v in-space propulsion systems. This work adds to a growing body of research and development efforts aimed at addressing the many anticipated challenges of implementing iodine as an in-space propellant. This work was conducted under the Advanced In-Space Propulsion (AISP) project funded through the Game Changing Development (GCD) program within NASA's Science Technology Mission Directorate (STMD).

Benavides, Gabriel F.↗

NASA NTRS2019

Electrical Power System Sizing Within the Numerical Propulsion System Simulation

Electrified aircraft propulsion seeks to address ambitious goals in the commercial airline industry, including significant decreases in fuel burn, emissions, noise, and takeoff field length. In order to move these electrified propulsion concepts forward, analysis tools are needed that can model propulsion systems containing both gas turbine and power system components. This work presents the definition of an electric port, a set of electrical power systems tools, and simulation examples for the Numerical Propulsion System Simulation (NPSS) software. NPSS is the industry standard modeling and simulation package for aircraft propulsion systems, and the ability to design, size, integrate, and analyze electric power systems will enable industry efforts towards the development of electrified aircraft propulsion.

aircraft electrification↗