Search NASA⌕ Search

Engineering topics

Thermal systems

Find NASA NTRS and DOE OSTI research on heat transfer and thermal systems. Search heat pipes, cooling and thermal management in report titles and abstracts.

Follow this topic with RSS
At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
NASA NTRS1998

Thermal High- and Low-Cycle Fatigue Behavior of Thick Thermal Barrier Coating Systems

Ceramic thermal barrier coatings have received increasing attention for advanced gas turbine and diesel engine applications because of their ability to provide thermal insulation to engine components. However, the durability of these coatings under the severe thermal cycling conditions encountered in a diesel engine (ref. 1) still remains a major issue. In this research at the NASA Lewis Research Center, a high-power laser was used to investigate the thermal fatigue behavior of a yttria-stabilized zirconia coating system under simulated diesel engine conditions. The mechanisms of fatigue crack initiation and propagation, and of coating failure under complex thermal low-cycle fatigue (LCF, representing stop/start cycles) and thermal high-cycle fatigue (HCF, representing operation at 1300 rpm) are described. Continuous wave and pulse laser modes were used to simulate pure LCF and combined LCF/HCF, respectively (ref. 2). The LCF mechanism was found to be closely related to the coating sintering and creep at high temperatures. These creep strains in the ceramic coating led to a tensile stress state during cooling, thus providing the major driving force for crack growth under LCF conditions. The combined LCF/HCF tests induced more severe coating surface cracking, microspallation, and accelerated crack growth than did the pure LCF test. HCF thermal loads also facilitated lateral crack branching and ceramic/bond coat interface delaminations. HCF is associated with the cyclic stresses originating from the high-frequency temperature fluctuation at the ceramic coating surface. The HCF thermal loads act on the crack by a wedging mechanism (ref. 1), resulting in continuous crack growth at temperature. The HCF stress intensity factor amplitude increases with the interaction depth and temperature swing, and decreases with the crack depth. HCF damage also increases with the thermal expansion coefficient and the Young's modulus of the ceramic coating (refs. 1 and 3).

Miller, Robert A.↗
DOE OSTI2024

Thermal Resilience of Residential Building with Thermally Anisotropic Building Envelope Connected to Geothermal Sources

Heat waves and cold snaps have become more frequent and more intense because of climate change. A heat wave and a cold snap are a period of excessively hot and cold weather, respectively, that poses severe risks to building occupants’ health, especially for vulnerable people. They increase electrical energy consumption and put high stress on the grid which leads to potential power outages. Therefore, it is critical to assess and actively improve the thermal resilience of buildings to cope with heat waves, cold snaps, and power outages. The thermally anisotropic building envelope (TABE) is a novel active building envelope that can save energy while maintaining thermal comfort in buildings by redirecting heat and coolness from building envelopes to hydronic loops. When connecting to a ground thermal loop (GL), TABE can utilize the relatively stable temperature of the ground to protect the indoor environment during heat waves and cold snaps. This study assesses the thermal resilience of residential buildings that installed TABE and used ground thermal energy to supply the hydronic loops, abbreviated as ground thermal loop or TABE+GL. The simulation and analysis are conducted for the US Department of Energy prototype single-family detached residential building in the hot climate of Miami, Florida and Tucson, Arizona, and the cold climate of Denver, Colorado, and Rochester, Minnesota. Heat waves and cold snaps were obtained from the historical weather data of 1998-2020 for the studied regions. Three thermal resilience metrics, including the standard effective temperature (SET) degree-hours, the Heat Index, and the Hours of Safety (HOS) were used to quantify the effect of TABE+GL. The results showed that buildings installed TABE+GL could significantly reduce the average SET degree-hours above 30°C, increase HOS, and greatly improve thermal resilience.

Shen, Zhenglai↗
DOE OSTI2024

Thermally anisotropic composites for thermal management in building environments

An improved system for thermal management is provided. The system includes thermally anisotropic composites coupled with a thermal loop to re-direct, reduce, and shape heat flows through a building envelope, having the potential to (1) significantly reduce envelope-generated heating and cooling loads and (2) provide grid services such as decreasing peak loads and shaping energy use. In one embodiment, the thermal management system includes an anisotropic composite that consists of alternating layers of thermal insulation and thermally conductive materials that are immediately adjacent to each other, including polyisocyanurate foam boards and aluminum sheets. The thermal management system also includes a thermal loop along the long edge or the entire the perimeter of the anisotropic composite, the thermal loop having dynamically controlled or floating temperature that is maintained at lower than an outdoor ambient temperature (for cooling). An interior wall structure is inwardly adjacent to the anisotropic composite.

Shrestha, Som S.↗
DOE OSTI2024

Structural and thermal properties and the origin of the ultralow thermal conductivity in the defect stannite CuIn 2 Se 4

Phase-pure CuIn 2 Se 4 , a ternary metal chalcogenide that forms in a disordered stannite crystal structure, was synthesized to investigate the structure thermal property relationships as well as reveal the origin of the ultralow thermal conductivity this material possesses over a large temperature range. Modeling of the temperature-dependent heat capacity and thermal conductivity revealed distinctive thermal properties and large lattice anharmonicity. Electron localization function calculations highlight the asymmetric bonding inherent to CuIn 2 Se 4 , which together with lattice anharmonicity directly impacts the thermal properties. Our findings reveal the specific atomic arrangement and bonding governing the thermal properties of this ternary metal chalcogenide. Our findings underscore the specific atomic arrangement and bonding governing the thermal properties in this ternary chalcogenide. This study advances the fundamental understanding of stannites, and our findings can be applied to these and other multinary metal chalcogenides of interest for applications where low thermal conductivity is desirable.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Origin of Intrinsically Low Thermal Conductivity in a Garnet-Type Solid Electrolyte: Linking Lattice and Ionic Dynamics with Thermal Transport

Understanding thermal transport in solid electrolytes is essential for improving the performance, reliability, and safety of all-solid-state batteries. Garnet-type lithium-ion conductors are promising candidates for solid electrolytes, yet their thermal-transport mechanisms remain poorly understood. Here, we connect the lattice and ion dynamics of single-crystal garnet-type Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 to its intrinsically low thermal conductivity. Our study reveals that the single crystals grown by the floating-zone method exhibit remarkably low glasslike thermal conductivity. Using first-principles calculations and inelastic-neutron-scattering measurements, we identify both the acoustic and numerous optical phonon modes, which stem from the complex crystal structure of the material. Notably, a low-energy optical branch exhibits an avoided crossing with acoustic phonons near 7 meV. These optical modes can enhance the scattering of heat-carrying acoustic phonons and reduce thermal conductivity. Furthermore, the calculated Grüneisen parameters are large, especially for the vibrational modes around 6 meV, indicating strong anharmonicity, with a noticeable contribution from lithium-ion vibrations. A two-channel thermal-transport model is employed to describe the weak temperature dependence of the thermal conductivity, which can be attributed to the substantial contribution of diffuson transport facilitated by the abundance of optical phonons and intrinsic anharmonicity. These results offer valuable insights into the thermal transport in a broad class of ionic conductors of interest for energy conversion and storage applications.

Ab initio calculations↗
DOE OSTI2024

Analysis of radially resolved thermal conductivity in high burnup mixed oxide fuel and comparison to thermal conductivity correlations implemented in fuel performance codes

The thermal diffusivity and thermal conductivity of high burnup (19 % FIMA) mixed oxide (U, Pu)O 2 nuclear fuel has been measured along the radial direction using a thermoreflectance-based method. Measured thermal conductivity exhibits a notable radial variation consistent with the expectations that a large temperature gradient across the annular fuel pellet leads to a heterogeneous microstructure. A common fuel performance model of thermal conductivity, the Lucuta-Inoue model, is used to analyze the measured thermal conductivity profile. Further, this model adequately captures the radial dependence of thermal conductivity except in the periphery. The analysis suggests that the characteristic radial shape of the thermal conductivity profile follows the burnup profile within the fuel pin. In the periphery, the high burnup structure is formed and the conductivity model, not capturing this effect, likely overestimates the thermal conductivity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dynamics and chemical mode analysis of plasma thermal-chemical instability

The stability of the weakly ionized plasma and the transition from a stable homogeneous discharge to unstable filaments play an important role in gas laser physics, plasma-assisted combustion, chemical reforming, and material synthesis. Here, theoretical stability analysis and thermal-chemical mode analysis were performed to understand the mechanism of plasma thermal-chemical instability by using a zero-dimensional plasma system with both simplified and detailed chemical kinetics of H 2 /O 2 /N 2 mixtures. The plasma dynamic and kinetic models accounted for multiple physical mechanisms in the chemically-reactive weakly ionized plasma, including ionization, attachment/detachment, recombination, vibrational and electronic energy relaxation, convective and diffusive species/heat removal, Joule heating, and detailed chemical kinetics. An analytical criterion and the explosive mode species/temperature pointers were formulated while the representative active species were identified for different thermal-chemical modes. The results showed that in addition to the classical thermal-ionization mechanism, various chemical modes from chemical heat imbalance and elementary kinetics significantly modified the time dynamics and the stability of the weakly ionized plasma. The present analysis provides insights and guidance to control plasma instability using chemical kinetics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2021

Precision Thermal Control (PTC) Technology to Enable Thermally Stable Telescopes

The Precision Thermal Control (PTC) project was a multiyear effort initiated in Fiscal Year 2017 to mature the Technology Readiness Level (TRL) of technologies required to enable ultra-thermally stable ultraviolet/ optical/infrared (UVOIR) space telescope primary-mirror (PM) assemblies for ultra-high-contrast observations of exoplanets. PTC had three objectives: (1) validate thermal optical performance models, (2) derive thermal system stability specifications, and (3) demonstrate multi-zonal active thermal control. PTC successfully achieved its objectives and matured active thermal control technology to at least TRL 5. PTC’s key accomplishments are a demonstration of better than 2-mK root-mean-square (rms) stable thermal control of the 1.5-m ultra-low-expansion (ULE®) Advanced Mirror Technology Development-2 (AMTD-2) mirror when exposed to thermal disturbances in a relevant thermal/vacuum environment, and the ability to shape the 1.5-m AMTD-2 mirror to picometer precision.

thermal control↗
DOE OSTI2024

Nanoscale Imaging and Measurements of Grain Boundary Thermal Resistance in Ceramics with Scanning Thermal Wave Microscopy

Material thermal conductivity is a key factor in various applications, from thermal management to energy harvesting. With microstructure engineering being a widely used method for customizing material properties, including thermal properties, understanding and controlling the role of extended phonon-scattering defects, like grain boundaries, is crucial for efficient material design. However, systematic studies are still lacking primarily due to limited tools. In this study, we demonstrate an approach for measuring grain boundary thermal resistance by probing the propagation of thermal waves across grain boundaries with a temperature-sensitive scanning probe. The method, implemented with a spatial resolution of about 100 nm on finely grained Nb-substituted SrTiO 3 ceramics, achieves a detectability of about 2 × 10 –8 K m 2 W –1 , suitable for chalcogenide-based thermoelectrics. The measurements indicated that the thermal resistance of the majority of grain boundaries in the STiO 3 ceramics is below this value. While there are challenges in improving sensitivity, considering spatial resolution and the amount of material involved in the detection, the sensitivity of the scanning probe method is comparable to that of optical thermoreflectance techniques, and the method opens up an avenue to characterize thermal resistance at the level of single grain boundaries and domain walls in a spectrum of microstructured materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Accelerating Discovery of Solid‐State Thin‐Film Metal Dealloying for 3D Nanoarchitecture Materials Design through Laser Thermal Gradient Treatment

Thin‐film solid‐state metal dealloying (thin‐film SSMD) is a promising method for fabricating nanostructures with controlled morphology and efficiency, offering advantages over conventional bulk materials processing methods for integration into practical applications. Although machine learning (ML) has facilitated the design of dealloying systems, the selection of key thermal treatment parameters for nanostructure formation remains largely unknown and dependent on experimental trial and error. To overcome this challenge, a workflow enabling high‐throughput characterization of thermal treatment parameters is demonstrated using a laser‐based thermal treatment to create temperature gradients on single thin‐film samples of Nb‐Al/Sc and Nb‐Al/Cu. This continuous thermal space enables observation of dealloying transitions and the resulting nanostructures of interest. Through synchrotron X‐ray multimodal and high‐throughput characterization, critical transitions and nanostructures can be rapidly captured and subsequently verified using electron microscopy. The key temperatures driving chemical reactions and morphological evolutions are clearly identified. While the oxidation may influence nanostructure formation during thin‐film treatment, the dealloying process at the dealloying front involves interactions solely between the dealloying elements, highlighting the availability and viability of the selected systems. Further, this approach enables efficient exploration of the dealloying process and validation of ML predictions, thereby accelerating the discovery of thin‐film SSMD systems with targeted nanostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermal, mechanical, and electrical properties of LSCo/mullite composite contact materials for solid oxide fuel cells

Lanthanum strontium cobaltite (LSCo) is considered as a good candidate cathode contact material for solid oxide fuel cells, due to high electrical conductivity. However, LSCo has a very large coefficient of thermal expansion (CTE) than the cells and metallic interconnects. As a result, poor mechanical stability is expected during thermal cycling. To minimize the CTE mismatch, we investigate a composite approach involving mixing LSCo with an inert material of low CTE, such as mullite at volume fractions from 0.1 to 0.4. Composite’s CTE shows a decreasing trend with increasing mullite volume fractions, and is consistent with model predictions. X-ray powder diffraction analysis of sintered LSCo/mullite composites exhibits no presence of other phases for samples aged for 500h at 800oC, indicating chemical compatibility. Electrical conductivity by a 4-pt method shows a decreasing trend with increasing mullite content. Contact strength of as-sintered and thermally cycled samples show that only the composite with 0.4 volume fraction has a measurable strength; the other composites have no strength. Overall, the composite approach is demonstrated in the LSCo/mullite system to lower the CTE and hence achieve thermal cycle stability. The addition of the inert phase to the LSCo matrix; however, also reduces the electrical conductivity.

Contact materials, LSCo, mullite, CTE, electrical ↗
DOE OSTI2020

A thermodynamics-based damage model for the non-linear mechanical behavior of SiC/SiC ceramic matrix composites in irradiation and thermal environments

A damage model is developed and validated with experimental data for the non-linear mechanical behavior of SiC/SiC composite materials in nuclear applications. Cyclic thermal and mechanical loading associated with neutron irradiation effects of these composites leads to wide-spread and progressive micro-cracking that leads to loss of thermal conductivity and further enhancement of thermo-mechanical damage. A physics-based model of wide-spread micro-cracking is developed within the thermodynamic framework of continuum damage mechanics. Evolution equations for damage parameters that describe the growth of continuum damage are developed, where the material variables are obtained from experiments. The model novelty is in coupling mechanical, thermal, and irradiation damage through a consistent thermodynamic framework, including loss of thermal conductivity due to the evolution of mechanically induced micro-cracks. A number of thermo-mechanical experiments were conducted to confirm model assumptions. The model is shown to be validated with out-of-pile experiments, and then implemented using commercial finite element code COMSOL to the fuel cladding problem with normal and high radiation dose cases.

Materials Science↗
DOE OSTI2022

A new dynamic zOnal model with air-diffuser (DOMA) - Application to thermal comfort prediction

A new Dynamic zOnal Model with Air-diffuser (DOMA) was developed. Several case studies were investigated and tested to evaluate and validate this program using measurement data. This new model was integrated into a TRaNsient SYstems Simulation program library and coupled with the multi-zone thermal model. The DOMA/TRNSYS coupled model was then used to predict room temperature distribution over an entire day of a single-zone building. The results show that increasing the heating outputs of the electric floor system, for example, from 75 to 200 W/m 2 , would not effectively improve the indoor thermal comfort, since the thermostat will reach the set point first and then turn off the system before the room gets enough heat and reach a comfortable level. This indicates the importance of selecting an appropriate location and set point for the thermostat when using a floor heating system. This potential thermal comfort issue can only be identified through the two-node model with a dynamic zonal model rather than the conventional PMV model, which thus suggests that for optimizing indoor thermal comfort of a building equipped with a time-sensitive control strategy and/or HVAC system, the TSENS results obtained from the two-node model integrated with DOMA are more appropriate than PMVs.

Construction & Building Technology↗
NASA NTRS1982

Two-layer thermal-barrier systems for Ni-Al-Mo alloy and effects of alloy thermal expansion on system life

Cyclic furnace and cyclic natural gas-oxygen torch rig tests were conducted to (1) identify a thermal-barrier system for a nickel-aluminum-molybdenum alloy, (2) study the oxidation of the bond coating, and (3) study the effect of the substrate coefficient of thermal expansion on thermal barrier system life. It is found that the latter is affected by the composition of the bond coating, yttria concentration in zirconia, and the coefficient of thermal expansion of the substrate material. In addition, small compositional changes in the bond and thermal barrier coatings have greater effect on thermal barrier system life than the 40% increase in the coefficient of thermal expansion of the substrate material. No simple relation exists between the weight gain caused by bond-coating oxidation with increasing yttria concentration in zirconia and increasing bond coating thickness on the one hand, and thermal barrier system life on the other.

Stecura, S.↗
NASA NTRS1999

Thermal Conductivity and Elastic Modulus Evolution of Thermal Barrier Coatings under High Heat Flux Conditions

Laser high heat flux test approaches have been established to obtain critical properties of ceramic thermal barrier coatings (TBCs) under near-realistic temperature and thermal gradients that may he encountered in advanced engine systems. Thermal conductivity change kinetics of a thin ceramic coating were continuously monitored in real time at various test temperatures. A significant thermal conductivity increase was observed during the laser simulated engine heat flux tests. For a 0.25 mm thick ZrO2-8%Y2O3 coating system, the overall thermal conductivity increased from the initial value of 1.0 W/m-K to 1. 15 W/m-K, 1. 19 W/m-K and 1.5 W/m-K after 30 hour testing at surface temperatures of 990C, 1100C, and 1320C. respectively. Hardness and modulus gradients across a 1.5 mm thick TBC system were also determined as a function of laser testing time using the laser sintering/creep and micro-indentation techniques. The coating Knoop hardness values increased from the initial hardness value of 4 GPa to 5 GPa near the ceramic/bond coat interface, and to 7.5 GPa at the ceramic coating surface after 120 hour testing. The ceramic surface modulus increased from an initial value of about 70 GPa to a final value of 125 GPa. The increase in thermal conductivity and the evolution of significant hardness and modulus gradients in the TBC systems are attributed to sintering-induced micro-porosity gradients under the laser-imposed high thermal gradient conditions. The test techniques provide a viable means for obtaining coating data for use in design, development, stress modeling, and life prediction for various thermal barrier coating applications.

Zhu, Dongming↗
NASA NTRS1996

Fossilization processes in siliceous thermal springs: trends in preservation along thermal gradients

To enhance our ability to extract palaeobiological and palaeoenvironmental information from ancient thermal spring deposits, we have studied the processes responsible for the development and preservation of stromatolites in modern subaerial thermal spring systems in Yellowstone National Park (USA). We investigated specimens collected from silica-depositing thermal springs along the thermal gradient using petrographic techniques and scanning electron microscopy. Although it is known that thermophilic cyanobacteria control the morphogenesis of thermal spring stromatolites below 73 degrees C, we have found that biofilms which contain filamentous thermophiles contribute to the microstructural development of subaerial geyserites that occur along the inner rims of thermal spring pools and geyser effluents. Biofilms intermittently colonize the surfaces of subaerial geyserites and provide a favoured substrate for opaline silica precipitation. We have also found that the preservation of biotically produced microfabrics of thermal spring sinters reflects dynamic balances between rates of population growth, decomposition of organic matter, silica deposition and early diagenesis. Major trends in preservation of thermophilic organisms along the thermal gradient are defined by differences in the mode of fossilization, including replacement, encrustation and permineralization.

NASA Discipline Exobiology↗
NASA NTRS1990

Thermal Conductivity and Temperature Limits of Electron-Beam Physical-Vapor-Deposited ZrO2-7wt%Y2O3 Thermal Barrier Coating

The electron-beam physical-vapor-deposited (EB-PVD) ZrO2-7wt%Y2O3 thermal barrier coating has been widely used to protect engine hot section components in modem aircraft engines. Thermal conductivity and the conductivity increases due to sintering and phase changes are important coating design parameters. There is a need to characterize the coating thermal conductivity behavior and temperature limits, in order to potentially take full advantage of the coating capability. In addition, since the ZrO2-7wt%Y2O3 coating is often used as a baseline coating for the development of advanced lower thermal conductivity and higher temperature capability coatings, a thorough evaluation of the coating conductivity behavior at future higher engine operating temperatures will be useful for more accurately assessing the benefit gained from the new coating systems. In this study, thermal conductivity behavior of EB-PVD ZrO2-7wt%Y2O3 coating has been systematically investigated as a function of temperature (up to 2600 F) and time under steady-state and cyclic test conditions using a laser heat-flux technique. Thermal conductivity change kinetics were determined under realistic engine high temperature thermal gradient conditions, and correlated to the coating microstructural and phase changes. The thermal conductivity prediction models have been established in terms of heat flux, time, and testing temperatures.

Zhu, Dongming↗