Battery cell thermal-conductive coating increases efficiency

Doyle, H. M.

Home/Archive/NASA NTRS

NASA NTRS · 19730000237

Battery cell thermal-conductive coating increases efficiency

Doyle, H. M.

View original source ↗Read source document ↗Export metadata ↓

Abstract

Thin coating of high-temperature epoxy resin provides necessary electrical insulation, as well as good thermal conductivity between battery cells. Insulation increases efficiency of nickel-cadmium battery, as it would any multicell battery assembly in which cell-to-cell thermal balance is critical.

Keep this discovery

BibTeX RIS

Doyle, H. M.. 1973-08-01. Battery cell thermal-conductive coating increases efficiency. https://ntrs.nasa.gov/citations/19730000237

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2019

Heat Transfer Enhancement in Cryogenic Quenching Process

This paper reports a heat transfer advancement in the cryogenic quenching process. An experiment was performed to evaluate the enhancement of quenching heat transfer by the use of metal tubes with low thermal conductivity coating layers. Four coating thicknesses with various coolant mass flow rates of liquid nitrogen were investigated. The results indicated that the tube inner surface coating greatly enhanced the quenching efficiency. The quenching efficiency was found to increase with increasing number of coating layers, and the efficiency also increased with decreasing mass flow rates. In general, the efficiencies cover a range between 40.6% and 80%. Comparing to the bare surface case, the percentage increase in the quenching efficiency was the minimum at 4.2% for a single coated layer at the highest flow rate and the maximum of 109.1% for four coated layers at the lowest flow rate. The coated tubes could save up to 53% in the amount of cryogen consumption.

two-phase flow↗

DOE OSTI2025

Advancements in nanocomposites for enhancing the performance of rechargeable lithium-ion batteries

The benefits of nanotechnology have been realized in almost every component of lithium-ion batteries. From electrodes to electrolytes, the incorporation of nanoparticles as dopants and coatings has shown marked improvements in cell cycle life, efficiency, mechanical and thermal stabilities, and lithium-ion transport. The improvements realized depends on several factors, from processing methods, nanoparticle type, structure, and concentration, to the material into which the nanoparticulate will be incorporated. Regardless of these many factors, nanotechnology has vastly improved the performance of secondary lithium-ion batteries. Here we will highlight some of the works that demonstrate these improvements and the quantitative benefits of nanotechnology.

25 ENERGY STORAGE↗

NASA NTRS2026

PROTECT: Production and Reuse of Thermally Efficient Ceramic Thermal Protection Systems

PROTECT (Production and Reuse Of Thermally Efficient Ceramic TPS) is a NASA Early Career Initiative focused on developing the next generation of reusable ceramic thermal protection systems (TPS). This project addresses key challenges in TPS design, including temperature capability, thermal stability, and refurbishment time, by integrating novel material development with predictive modeling. Leveraging enhanced capabilities in NASA’s Porous Microstructure Analysis (PuMA) software, PROTECT introduces new modeling tools to predict the thermal and mechanical behavior of fibrous ceramic materials. These tools enable accurate prediction of performance metrics such as thermal conductivity and structural integrity, reducing reliance on costly physical testing. Preliminary advances in these areas will be presented. To support model validation, PROTECT is building a comprehensive database of raw material properties using advanced characterization techniques, including micro computed tomography (CT) scanning in collaboration with the University of Illinois Urbana-Champaign (UIUC). The presentation will detail the sampling workflows and analysis methods used to generate this detailed microstructural data and how it is used to develop improved models in PuMA. This multi-center collaboration, spanning NASA (JSC, ARC, KSC, GRC), Oak Ridge National Laboratory, UIUC, and SpaceX, is developing tailored TPS solutions for LEO, lunar, and Martian missions. By bridging heritage systems with the demands of modern spaceflight, PROTECT contributes to the advancement of reusable TPS technologies for future exploration missions.

Propulsion, Refractory, and Coating Materials↗