Search NASA⌕ Search
Home/Archive/NASA NTRS

NASA NTRS · 20170008731

Ice Accretion Roughness Measurements and Modeling

McClain, Stephen T.·Vargas, Mario·Tsao, Jen-Ching·Broeren, Andy P.·Lee, Sam
View original source ↗Export metadata ↓

Abstract

Roughness on aircraft ice accretions is very important to the overall ice accretion process and to the resulting degradation in aircraft aerodynamic performance. Roughness enhances the local convection leading to more rapid ice accumulation rates, and roughness generates local flow perturbations that lead to higher skin friction. This paper presents 1) a review of the developments in ice shape three-dimensional laser scanning developed at NASA Glenn, 2) a review of the approach of McClain and Kreeger employed to characterize ice roughness evolution on an airfoil surface, and 3) a review of the experimental efforts that have been performed over the last five years to characterize, scale, and model ice roughness evolution physics.

Explore related subjects

SLDice accretionaircraft icing

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

McClain, Stephen T., Vargas, Mario, Tsao, Jen-Ching, Broeren, Andy P., Lee, Sam. 2017-07-03. Ice Accretion Roughness Measurements and Modeling. https://ntrs.nasa.gov/citations/20170008731

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2016

Additional Results of Glaze Icing Scaling in SLD Conditions

New guidance of acceptable means of compliance with the super-cooled large drops (SLD) conditions has been issued by the U.S. Department of Transportation's Federal Aviation Administration (FAA) in its Advisory Circular AC 25-28 in November 2014. The Part 25, Appendix O is developed to define a representative icing environment for super-cooled large drops. Super-cooled large drops, which include freezing drizzle and freezing rain conditions, are not included in Appendix C. This paper reports results from recent glaze icing scaling tests conducted in NASA Glenn Icing Research Tunnel (IRT) to evaluate how well the scaling methods recommended for Appendix C conditions might apply to SLD conditions. The models were straight NACA 0012 wing sections. The reference model had a chord of 72 in. and the scale model had a chord of 21 in. Reference tests were run with airspeeds of 100 and 130.3 kn and with MVD's of 85 and 170 micron. Two scaling methods were considered. One was based on the modified Ruff method with scale velocity found by matching the Weber number WeL. The other was proposed and developed by Feo specifically for strong glaze icing conditions, in which the scale liquid water content and velocity were found by matching reference and scale values of the nondimensional water-film thickness expression and the film Weber number Wef. All tests were conducted at 0 deg AOA. Results will be presented for stagnation freezing fractions of 0.2 and 0.3. For nondimensional reference and scale ice shape comparison, a new post-scanning ice shape digitization procedure was developed for extracting 2-D ice shape profiles at any selected span-wise location from the high fidelity 3-D scanned ice shapes obtained in the IRT.

SLD↗
NASA NTRSDate not supplied

Analysis of Supercooled Large Drop Velocity Measurement in the NASA Icing Research Tunnel

An experiment was conducted in the Icing Research Tunnel (IRT) at the NASA Glenn Research Center to measure the velocity of supercooled large drops (SLD) in the test section of the tunnel. Previous experiments in the IRT suggested that supercooled large drops passing through the test section of the tunnel do not move at the same velocity as the surrounding air flow. The difference between drop velocity and tunnel air velocity is called slip velocity. The slip velocity is important for determining the exact nature of SLD icing simulation in the IRT. It can impact the ice growth process because of its effect on drop cooling rate during transit from the spray bars to the test section. It can also affect the amount of splashing that occurs upon impact. Slip velocity is an important flow parameter to determine how far the current facility capabilities can be extended into the SLD regime. Initial measurement data analysis of the drop velocities indicates that drops with diameter larger than about 100 to 200 µm experience velocity slip.

SLD↗
NASA NTRSDate not supplied

Characterization of Large Drop Velocity in the NASA Icing Research Tunnel

This paper presents experimental work conducted in the Icing Research Tunnel at NASA Glenn Research Center to characterize the velocity of large drops in the test section. Some icing spray clouds with large drops were generated with Mod1 nozzles at low nozzle air pressure of 2 to 4 psig for various tunnel air speeds. Drop diameters and drop velocities were measured via high-resolution imaging with a Particle Imaging Particle Tracking Velocimetry probe developed by Artium Technologies. The probe was mounted at four different locations aligned with the centerline of the test section from near the end of the contraction to the constant height test section part of the tunnel. CFD analyses were performed. It showed that the probe head geometry affects the local air flow in the measurement area of the probe between the prongs and in front of the probe. Initial analysis of the air velocity data during the test also indicated that the probe mounting stand has blockage effect on the local tunnel air velocity measurement by a pitot-static probe affixed on the mounting plate next to the stand. Those findings were later verified in the Icing Research Tunnel using a new pitot-static probe design with a linear motion system to measure the local tunnel air velocity with and without the probe. As a result, additional drop trajectory simulations were performed with the airflow moving towards the probe head with a Langmuir-D 7-bin distribution cloud containing large drops. The simulation results helped identify a critical drop-size threshold of 300 μm above which the velocities of larger drops are negligibly affected by the adverse pressure gradient generated by the probe head due to their large drop inertia. From the dimensional analysis of the drop velocity measurement data obtained, it showed that at the tunnel test section reference location a generalized empirical correlation was developed for the non-dimensional drop velocity as a function of the non-dimensional corrected drop diameter independent of the actual spraybar pressure settings and the tunnel air speeds. The generalized curve-fit correlation showed that the drop velocity was universally asymptotic to about 86 percent of the corresponding tunnel air speed at the test section reference location for the largest drop diameter captured by the probe. Further evaluation of this correlation is recommended to assess its applicability for Supercooled Large Drop icing scaling applications in the Icing Research Tunnel.

SLD↗