Search NASA⌕ Search

NASA NTRS · 20190027633

Instability Wave-Streak Interactions in a Supersonic Boundary Layer

Abstract

Optimal initial conditions for transient growth in a two-dimensional boundary layer flow correspond to stationary, counter-rotating vortices that subsequently develop into streamwise elongated streaks, which are characterized by an alternating pattern of low and high streamwise velocity. For incompressible flows, previous studies have shown that boundary layer modulation due to streaks below a threshold amplitude level can stabilize the Tollmien-Schlichting instability waves, resulting in a delay in the onset of laminar-turbulent transition. In the supersonic regime, the linearly, most-amplified waves become three-dimensional, corresponding to oblique, first-mode waves. This change in the character of dominant instabilities leads to an important change in the transition process, which is now dominated by oblique breakdown via nonlinear interactions between pairs of first-mode waves that propagate at equal but opposite angles with respect to the free stream. Because the oblique breakdown process is characterized by a rapid amplification of stationary streamwise streaks, artificial excitation of such streaks may be expected to promote transition in a supersonic boundary layer. Indeed, suppression of those streaks has been shown to delay the onset of transition in prior literature. Consistent with those findings, the present study shows that optimally growing stationary streaks indeed destabilize the first-mode waves, but only when the spanwise wavelength of the instability waves is equal to or smaller than twice the streak spacing. Transition in a benign disturbance environment typically involves first-mode waves with significantly longer spanwise wavelengths, and hence, these waves are stabilized by the optimal growth streaks. Thus, as long as the amplification factors for the destabilized, short wavelength instability waves remain below the threshold level for transition, a significant net stabilization is achieved, yielding a transition delay that is comparable to the length of the laminar region in the uncontrolled case.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Pedro Paredes, Meelan M Choudhari, Fei Li. 2017-10-13. Instability Wave-Streak Interactions in a Supersonic Boundary Layer. https://ntrs.nasa.gov/citations/20190027633

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Measurements and Computations of Natural Transition on the NASA Juncture-Flow Model with a Symmetric Wing

Experiments were performed in the 14- by 22-Foot Subsonic Tunnel to assess natural transition on the symmetric-airfoil wings of the NASA Juncture-Flow Model. Infrared thermography was used to visualize the heating on the upper surface of both wings of the full-span model, and on the fuselage, for angles of incidence ranging from -10° to 10° at a fixed Reynolds number of 2.4E6 based on the chord length at the wing planform break. The fuselage boundary layer transitioned well upstream of the wing-root leading edge for all conditions. Transition fronts were identified by a steep rise in the surface temperature, and the transition coordinates were transformed from an image-based to a body-fixed system. Additionally, the state of the boundary layer was estimated at pressure ports distributed on the wings through observation of the pressure coefficient as a function of the angle of incidence. For increasing angles of incidence, the transition front was observed to advance upstream, in a mostly spanwise-uniform fashion, from near midchord at α = 0°; however, for increasingly negative angles of incidence, the transition front first receded and then advanced in a nonuniform jagged manner that is typically observed with stationary crossflow. The transition wedges first appeared inboard of the wing break and then spread outboard to near the tip by α = -6°. The upstream shift in transition at positive angles of incidence and the outboard progression of crossflow-dominated transition at increasingly negative angles of incidence are consistent with trends identified in a computational assessment of the boundary-layer transition based on both linear stability analysis and Reynolds-averaged-Navier-Stokes-based transition models. The stability results obtained from the Langley Stability and Transition Analysis Code were used to recalibrate a dual N-factor criterion, which allowed for the prediction of transition fronts that showed excellent agreement with the experiment. The Reynolds-averaged-Navier-Stokes-based models, from the NASA OVERFLOW 2.3 solver, that accounted for the crossflow instability showed mixed results in comparison with the experiment, with the helicity-based Langtry-Menter model performing the best. The experimental data, particularly the cases involving strong influence from both Tollmien-Schlichting and crossflow instabilities, will be valuable for the continued validation and improvement of transition models.

Boundary layer transition↗

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Modal and nonmodal instability characteristics of cylindrically blunted flat plates with varying leading edge radii are described for Mach 4 and Mach 6 freestream conditions. The selection of leading edge radii and freestream parameters is informed by experimental conditions. The investigation of this 2D problem provides a slow entropy layer swallowing which allows for an isolated development of perturbations seeded upstream within different wall-normal regions of the flow. At both Mach numbers, a decrease in modal instability amplification was seen as the leading edge radius was increased. Nonmodal analysis reveals amplifying perturbations in the boundary layer as well as in the entropy layer. The medium bluntness regime exhibits the strongest amplification of nonmodal disturbances that is nonmonotonic in character. Small amplitude boundary forcing at the plate surface or volumetric forcing at various wall-normal heights was used to account for receptivity effects. While wall forcing effectively induced modal instabilities, only an actuation above the boundary layer captured disturbances that amplify within the entropy layer. The optimal nonmodal theory’s entropy-layer disturbance evolution exhibited outstanding agreement with controlled forcing, including receptivity effects. The evolution of entropy-layer disturbances from the optimal nonmodal theory showed excellent agreement with the results of receptivity to controlled forcing. Therefore, the nonmodal optimal growth analysis may provide a useful as well as efficient technique to identify the complete disturbance spectrum in blunt hypersonic configurations, where both modal and nonmodal disturbances can amplify in the boundary-layer and entropy-layer regions.

Boundary layer transition↗

Stability Analysis of Streaks Induced By Optimized Vortex Generators

Numerical computations are performed to investigate the potential for transition control in an axisymmetric boundary layer via fully realizable, streamwise stationary streaks induced by an azimuthally periodic array of surface mounted vortex generators (VGs). Previous work has shown that suitable streaks of this type can significantly reduce the growth of Mack’s second mode instabilities, but large streak amplitudes can make the flow susceptible to previously absent streak instabilities that can become the leading cause of transition. Here, we use the adjoint capabilities of the SU2 flow solver to optimize the VG shape to maximize the reduction in the growth of second-mode disturbances while also preventing the streak amplitudes from reaching large enough values to precipitate an earlier onset of transition via streak instabilities. The geometry and the freestream flow conditions are selected to match a relevant trajectory lo-cation from the HIFiRE-1 flight experiment. Results show that the optimized VGs can increase the mean streak amplitude by 117% with respect to a manually developed baseline design. The stability of this optimized basic state is analyzed via the plane-marching parabolized stability equations, predicting a fully laminar flow over the entire cone, or equivalently, yielding transition delay of 130% versus the 17% for the baseline VGs.

Boundary layer transition↗