Search NASA⌕ Search
Home/Archive/NASA NTRS

NASA NTRS · 20210004347

Technology for Space Optical Interferometry

Fanson, James L.·Laskin, Robert A.
View original source ↗Export metadata ↓

Abstract

The Micro-Precision Control/Structure Interaction (CSI) program at JPL is chartered to develop the structures and control technology needed for sub-micron level stabilization of future optical space systems. The extreme dimensional stability required for such systems derives from the need to maintain the alignment and figure of critical optical elements to a small fraction (typically 1/20th to 1/50th) of the wavelength of detected radiation (about 0.5 micron for visible light, 0.1 micron for ultraviolet light). This requirement is common to a broad class of optical sysetms. The challenge for CSI arises when such systems become large, with spatially distributed optical elements mounted on lightweight, flexible structure. This paper will present an overview of the approach that is being taken by JPL's CSI program to address this challenge. In particular, the paper will discuss the application of CSI technology to a specific example of a future large optical space mission. Experimental demonstration of the technology on ground-based testbeds will also be presented.

Explore related subjects

structurescontroltechnologyCSItestbedopticalinterferometryspacesystemsmicroprecisionstabilizationflexible

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Fanson, James L., Laskin, Robert A.. 1995-01-01. Technology for Space Optical Interferometry. https://ntrs.nasa.gov/citations/20210004347

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2019

Inflatable Technology: Using Flexible Materials to Make Large Structures

Space structures are one of the most critical components for any spacecraft, as they must provide the maximum amount of livable volume with the minimum amount of mass. Deployable structures can be used to gain additional space that would not normally fit under a launch vehicle shroud. This expansion capability allows it to be packed in a small launch volume for launch, and deploy into its fully open volume once in space. Inflatable, deployable structures in particular, have been investigated by NASA since the early 1950’s and used in a number of spaceflight applications. Inflatable satellites, booms, and antennas can be used in low-Earth orbit applications. Inflatable heatshields, decelerators, and airbags can be used for entry, descent and landing applications. Inflatable habitats, airlocks, and space stations can be used for in-space living spaces and surface exploration missions. Inflatable blimps and rovers can be used for advanced missions to other worlds. These applications are just a few of the possible uses for inflatable structures that will continued to be studied as we look to expand our presence throughout the solar system.

structures↗
NASA NTRS2014

Characterization and Comparison of Vibration Transfer Paths in a Helicopter Gearbox and a Fixture Mounted Gearbox

Health monitoring of rotorcraft components, currently being performed by Health and Usage Monitoring Systems through analyses of vibration signatures of dynamic mechanical components, is very important for their safe and economic operation. HUMS analyze vibration signatures associated with faults and quantify them as condition indicators to predict component behavior. Vibration transfer paths are characterized by frequency response functions derived from the input/output relationship between applied force and dynamic response through a structure as a function of frequency. With an objective to investigate the differences in transfer paths, transfer path measurements were recorded under similar conditions in the left and right nose gearboxes of an AH-64 helicopter and in an isolated left nose gearbox in a test fixture at NASA Glenn Research Center. The test fixture enabled the application of measured torques-common during an actual operation. An impact hammer as well as commercial and lab piezo shakers, were used in conjunction with two types of commercially available accelerometers to collect the vibration response under various test conditions. The frequency response functions measured under comparable conditions of both systems were found to be consistent. Measurements made on the fixture indicated certain real-world installation and maintenance issues, such as sensor alignments, accelerometer locations and installation torques, had minimal effect. However, gear vibration transfer path dynamics appeared to be somewhat dependent on the presence of oil, and the transfer path dynamics were notably different if the force input was on the internal ring gear rather than on the external gearbox case.

structures↗