The Two-Cavity Method for Characterizing Acoustical Materials—an Interlaboratory Study

Martha C. Brown; Anthony Ciletti; Janith Godakawela; Bhisham Sharma

NASA NTRS · 20240004220

The Two-Cavity Method for Characterizing Acoustical Materials—an Interlaboratory Study

Martha C. Brown·Anthony Ciletti·Janith Godakawela·Bhisham Sharma

Abstract

This study focuses on understanding the sound absorption characteristics of porous acoustic materials, which are determined by two key parameters independent of material thickness: characteristic impedance and propagation constant. These parameters can be characterized by testing a porous sample concept in a normal incidence impedance tube using either the two-thickness or the two-cavity method. In the two-thickness method, two samples of varying thicknesses are required. In contrast, the two-cavity method requires testing one sample at two different air cavity depths behind the porous material. This method is particularly advantageous for materials that are costly or challenging to fabricate. This interlaboratory study evaluates the variability of characteristic properties determined using the two-cavity method. Porous acoustic materials were additively manufactured and tested in the Liner Technology Facility(LTF)at NASA Langley Research Center and the Mechanics, Acoustics and Dynamics Lab (MADLab) at Michigan Technological University. The characteristic properties derived from various cavity depth combinations were used to predict the surface impedance of the sample with a rigid backing. The prediction was then compared the measured impedance spectrum. It was also found that the combinations of cavity depths can significantly influence the accuracy of the deduced properties.

Explore related subjects

acoustic liners TPMS bulk absorber porous materials porous media

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Martha C. Brown, Anthony Ciletti, Janith Godakawela, Bhisham Sharma. The Two-Cavity Method for Characterizing Acoustical Materials—an Interlaboratory Study. https://ntrs.nasa.gov/citations/20240004220

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2023

Effects of Layer Spacing for a Multilayered Facesheet Acoustic Liner

A single degree-of-freedom acoustic liner, a perforate facesheet over honeycomb core, is modified to have a facesheet comprised of three layers. The top and bottom perforate layers have the same dimensions with aligned perforations while the middle layer perforate can be longitudinally shifted up to 0.075 inches to change the effective porosity of the facesheet. These configurations range in porosity from 100% open down to 10% open in addition to two closed configurations (0% porosity). Gaps are introduced between the facesheet layers ranging from no gap to 0.016 inches. These configurations are tested in the NASA Langley Grazing Flow Impedance Tube to determine their acoustic impedance spectra. Introduction of a gap affects the acoustic impedance of the liner where the resonant frequency of the liners decreases with increased gap thickness for liners with an open area ratio above 25% but increases with gap thickness for liners with an open area ratio below 25%. Additionally, it is observed that increasing the gap height results in a reduction of the effect of porosity on acoustic impedance. The results show that the presence of such gaps can have a significant effect on liner impedance especially as porosity decreases.

acoustic liners↗

NASA NTRS2015

A Fully Non-Metallic Gas Turbine Engine Enabled by Additive Manufacturing Part I: System Analysis, Component Identification, Additive Manufacturing, and Testing of Polymer Composites

The research and development activities reported in this publication were carried out under NASA Aeronautics Research Institute (NARI) funded project entitled "A Fully Nonmetallic Gas Turbine Engine Enabled by Additive Manufacturing." The objective of the project was to conduct evaluation of emerging materials and manufacturing technologies that will enable fully nonmetallic gas turbine engines. The results of the activities are described in three part report. The first part of the report contains the data and analysis of engine system trade studies, which were carried out to estimate reduction in engine emissions and fuel burn enabled due to advanced materials and manufacturing processes. A number of key engine components were identified in which advanced materials and additive manufacturing processes would provide the most significant benefits to engine operation. The technical scope of activities included an assessment of the feasibility of using additive manufacturing technologies to fabricate gas turbine engine components from polymer and ceramic matrix composites, which were accomplished by fabricating prototype engine components and testing them in simulated engine operating conditions. The manufacturing process parameters were developed and optimized for polymer and ceramic composites (described in detail in the second and third part of the report). A number of prototype components (inlet guide vane (IGV), acoustic liners, engine access door) were additively manufactured using high temperature polymer materials. Ceramic matrix composite components included turbine nozzle components. In addition, IGVs and acoustic liners were tested in simulated engine conditions in test rigs. The test results are reported and discussed in detail.

acoustic liners↗

NASA NTRSDate not supplied

Preliminary Design of a Distributed Facesheet Acoustic Liner for Broadband Acoustic Attenuation

The purpose of this study is to investigate the acoustic performance of a liner with a distributed facesheet and a uniform depth core for broadband attenuation. The distributed facesheet is comprised of a cluster of three distinct cell resonators of varying hole diameter and porosity replicated over the active liner treatment area. A target frequency range of 1000 to 2000 Hz and an attenuation metric of 10 dB are chosen. An optimizer is used to determine the optimal facesheet designs for flow conditions of Mach 0.0 and Mach 0.3. The samples are tested in the Grazing Flow Impedance Tube at NASA Langley Research Center. The two liners are shown to achieve at least 10 dB attenuation over frequency ranges of 700 and 400 Hz, respectively, when tested at their respective designed flow speeds. This study demonstrate that a distributed facesheet with a uniform depth core can be successfully used to achieve broadband sound absorption.

acoustic liners↗