Search NASA⌕ Search

DOE OSTI · 1605203

Axial Relocation Model Extension in Bison

Abstract

Fuel rods subjected to a Loss of Coolant Accident (LOCA) in a nuclear reactor can undergo a complex process known as fuel fragmentation, relocation, and dispersal (FFRD). The loss of coolant results in a severe degradation of the thermal heat transfer coefficient on the waterside surface of the cladding. This, coupled with the loss of coolant pressure causes the cladding to distend (balloon) outward. If the cladding distention is large enough, fuel fragmented during irradiation, may relocate from upper regions of the rod into the ballooned region. This mass relocation results in increased localized heating due to the presence of more fuel within the balloon resulting in further clad distention leading to potential rupture of the cladding. In the event that cladding rupture occurs the relocated fragmented fuel may disperse outside of the rupture opening if the size of the fuel fragments is small enough. Fuel performance modeling can be used to help understand the behavior of fuel rods during the LOCA transient. Existing models are particularly limited in regards to FFRD. This report briefly describes the existing state of the art for fuel performance modeling of fragmentation and fuel axial relocation. A more in depth description the axial relocation model implemented into the Bison fuel performance code in FY17 is provided. In this report, the extension of this existing model from a layered 1D framework to a 2D framework that allows for the introduction of azimuthal variation in the boundary conditions as experienced during a LOCA is discussed. The 2D framework utilized has been developed by the author of this report as part of his dissertation research ongoing at the University of South Carolina under the direction of Professor Travis W. Knight. The report briefly describes the 2D framework used and highlights in more detail the required developments in Bison to facilitate the extension of the axial relocation model to work within this framework. Finally, a few demonstration cases are provided that illustrate the benefit of using the new extended axial relocation model for the simulation of fuel rods under LOCA conditions.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Gamble, Kyle A.. 2018-08-31. Axial Relocation Model Extension in Bison. https://doi.org/10.2172/1605203. https://searchnasa.com/record/osti%3A1605203/axial-relocation-model-extension-in-bison

Citations retain the original authors and DOI and include this site’s record URL. If this discovery service contributed to your research, you can also cite Search NASA by Indiciae: BibTeX · RIS.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗