Search NASA⌕ Search

DOE OSTI · 1784137

Performance and community structure dynamics of microbial electrolysis cells operated on multiple complex feedstocks

Abstract

Microbial electrolysis is a promising technology for converting aqueous wastes into hydrogen. However, substrate adaptability is an important feature, seldom documented in microbial electrolysis cells (MECs). In addition, the correlation between substrate composition and community structure has not been well established. This study used an MEC capable of producing over 10 L/L-day of hydrogen from a switchgrass-derived bio-oil aqueous phase and investigated four additional substrates, tested in sequence on a mature biofilm. The additional substrates included a red oak-derived bio-oil aqueous phase, a corn stover fermentation product, a mixture of phenol and acetate, and acetate alone. The MECs fed with the corn stover fermentation product resulted in the highest performance among the complex feedstocks, producing an average current density of 7.3 ± 0.51 A/m 2 , although the acetate fed MECs outperformed complex substrates, producing 12.3 ± 0.01 A/m 2 . 16S rRNA gene sequencing showed that community structure and community diversity were not predictive of performance, and replicate community structures diverged despite identical inoculum and enrichment procedure. The trends in each replicate, however, were indicative of the influence of the substrates. Geobacter was the most dominant genus across most of the samples tested, but its abundance did not correlate strongly to current density. High-performance liquid chromatography (HPLC) showed that acetic acid accumulated during open circuit conditions when MECs were fed with complex feedstocks and was quickly degraded once closed circuit conditions were applied. The largest net acetic acid removal rate occurred when MECs were fed with red oak bio-oil aqueous phase, consuming 2.93 ± 0.00 g/L-day. Principal component analysis found that MEC performance metrics such as current density, hydrogen productivity, and chemical oxygen demand removal were closely correlated. Net acetic acid removal was also found to correlate with performance. However, no bacterial genus appeared to correlated to these performance metrics strongly, and the analysis suggested that less than 70% of the variance was accounted for by the two components. This study demonstrates the robustness of microbial communities to adapt to a range of feedstocks and conditions without relying on specific species, delivering high hydrogen productivities despite differences in community structure. The results indicate that functional adaptation may play a larger role in performance than community composition. Further investigation of the roles each microbe plays in these communities will help MECs to become integral in the 21st-century bioeconomy to produce zero-emission fuels.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Satinover, Scott J., Rodriguez, Jr., Miguel, Campa, Maria F., Hazen, Terry C., Borole, Abhijeet P.. 2020-10-13. Performance and community structure dynamics of microbial electrolysis cells operated on multiple complex feedstocks. https://doi.org/10.1186/s13068-020-01803-y

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Hydrotreating pine-derived catalytic fast pyrolysis oil to jet fuel: Process durability and impact of operating conditions

Hydrotreating woody biomass-derived catalytic fast pyrolysis (CFP) oil to jet fuel has the potential to enhance energy security due to the large abundance of forest and woody resources. CFP oil produced from pine over ZSM-5 was hydrotreated over sulfided NiMo/Al 2 O 3 for 410 h to study the impact of hydrotreating conditions (pressure, temperature, and weight hourly space velocity (WHSV)). The degree of deoxygenation remained high across the tested hydrotreating conditions, and the products contained < 0.01 wt% oxygen. Increasing hydrotreating pressure from 84 to 125 bar enhanced hydrogenation of aromatic rings and the formation of cycloalkanes and increasing the temperature from 385 to 400 degrees C enhanced cracking and the formation of jet-range molecules. Decreasing the weight hourly space velocity from 0.2 to 0.1 g/(g cat h) further enhanced cracking and led to higher gasoline- and lower jet fuel-range fractions. The highest jet fuel fraction (49 wt%) was obtained at 400 degrees C, 125 bar, 0.2 g/(g cat h) WHSV. CFP oils produced from pine over phosphorous-modified ZSM-5 were hydrotreated at this condition for 588 h to investigate the process durability. The hydrogenation performance of the catalyst gradually stabilized in approximately 300 h after which the product composition remained constant. Of the final hydrotreated CFP oil, 53 wt% fell in the jet fuel range with most of the tested fuel properties meeting ASTM D4054 and/or ASTM D7566 specifications. The freeze points were < -50 degrees C vs. guideline of < -40 degrees C and the viscosities at -20 degrees C were 3.8-4.1 mm 2 /s vs guideline of 8 mm 2 /s. Increasing the fraction of cycloalkanes could increase the cetane number and heating value, which did not meet the guidelines.

09 BIOMASS FUELS↗

Suppressing CO formation in low-temperature methanol steam reforming via Ce-modified CuZnGa layered oxide catalysts

Cu-based layered double hydroxides (LDHs) are widely recognized as effective catalysts for low-temperature methanol steam reforming, yet achieving high hydrogen productivity together with near-complete suppression of CO formation remains challenging. Here, we report the synthesis and evaluation of a series of CuZnGa LDH-derived catalysts and Ce-modified analogues prepared via an aqueous miscible organic method, which enables high metal dispersion and precise structural control. The optimized CuZnGa catalyst exhibits a hydrogen production rate of 16.9 µmol H 2 ·g cat −1 ·s −1 at 180 °C with an H 2 /CO ratio exceeding 3500, outperforming many state-of-the-art low-temperature systems. Importantly, the incorporation of small amounts of Ce further suppresses CO formation while maintaining high hydrogen productivity. Combined spectroscopic characterization and density functional theory calculations reveal that Ce is incorporated into the LDH lattice by substituting Ga 3+ sites up to a critical threshold, beyond which highly dispersed CeO x species are formed. These species provide mobile lattice oxygen that participates in a Mars-van Krevelen-type pathway, selectively oxidizing CO and suppressing the reverse water-gas shift reaction. This study establishes a clear relationship between Ce speciation, oxygen mobility, and catalytic selectivity in LDH-derived systems. The resulting catalysts demonstrate the potential of interface-engineered Cu-based materials for efficient low-temperature hydrogen production with minimal CO contamination.

09 BIOMASS FUELS↗

Graphitization of banana peel – synergistic effect of Ca and other elements of the biomass on carbon structure transformation

Recently, growing interest has been observed in using calcium as an effective catalyst for graphitizing disordered carbon materials derived from biomass and bioprecursors, such as cellulose and lignin, at relatively low tem peratures (<2000 °C). Herein, it is demonstrated that in the presence of elements such as calcium, silicon, sulfur, and potassium, which are abundant in banana peel composed of cellulose and lignin base, graphitization occurs much more effectively. The addition of external calcium source, in the form of calcium carbonate, to the banana peel-derived carbon and heat-treatment of the mixture under protective atmosphere up to 1750 °C results in a significant increase in the degree of the graphitization order and local formation of graphite crystals, whereas the same preparation and heat-treatment procedure applied to carbon material derived from pristine cellulose does not lead to such effective graphitization. It is indicated that the graphitization of banana peel carbon occurs due to the synergistic effect of the external Ca-based catalyst and the internal elements present in the raw biomass, supporting the transformation of the disordered graphene-like layers into graphitic structures. These findings are important for the future production of green graphite from biomass

09 BIOMASS FUELS↗