Search NASA⌕ Search

DOE OSTI · 1785547

Nitrogen derived from Combined Algal Processing supports algae cultivation for biofuels

Also available from

Abstract

Algae biomass, a biofuel feedstock with potential to reduce global CO 2 emissions, is currently too expensive Nitrogen, a significant input and life cycle cost, requires research on recycling and additional sources to reduce costs. Integral to nitrogen recycling is the knowledge of actual nitrogen requirements in outdoor ponds, thus data from the Unified Field Studies of the Algae Testbed Public-Private Partnership was analyzed. The data showed that Nannochloropsis oceanica used 14–24 mg/L NH 4 + per harvest cycle for robust growth. Nitrogen recycled directly from the algae conversion process will likely be the primary source of nitrogen for algae cultivation. Harvested algae can be fractionated via Combined Algal Processing (CAP), where algae are pretreated, fermented, and the fuel feedstocks (e. g. ethanol, lipids) are removed leaving a nitrogen rich slurry. Chlorella vulgaris grew robustly in nitrogen-free media supplemented with CAP residues through 4 harvest cycles with no inhibition. The amount of nitrogen as free ammonium available for recycling directly without further processing was insufficient (~4% of total needed), thus the nitrogen fixing bacteria, Azotobacter vinelandii, was investigated as a means for increasing ammonium concentration in CAP residues. This organism was shown to be proficient at growth on sugars liberated from algae biomass during pretreatment and sustained algae growth using A. vinelandii supernatants was also demonstrated. Using Azotobacter to increase ammonium concentrations on-site using an inexpensive biological process to generate the necessary ammonium for outdoor algae cultivation improves sustainability of algae biofuels by avoiding the energy intensive steps of typical ammonium production and transport. Furthermore, these results show that byproducts of algae conversion begin to close nitrogen demand and, with further supplementation by diazotrophic bacteria or protein hydrolysis, may completely replace current energyintensive and costly industrial nitrogen sources offering a path to increased economic feasibility and improved life cycle analysis of algae-based biofuels.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Savage, Evan, Nagle, Nick, Laurens, Lieve M. L., Knoshaug, Eric P.. 2020-07-04. Nitrogen derived from Combined Algal Processing supports algae cultivation for biofuels. https://doi.org/10.1016/j.algal.2020.101987

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Hydrotreating pine-derived catalytic fast pyrolysis oil to jet fuel: Process durability and impact of operating conditions

Hydrotreating woody biomass-derived catalytic fast pyrolysis (CFP) oil to jet fuel has the potential to enhance energy security due to the large abundance of forest and woody resources. CFP oil produced from pine over ZSM-5 was hydrotreated over sulfided NiMo/Al 2 O 3 for 410 h to study the impact of hydrotreating conditions (pressure, temperature, and weight hourly space velocity (WHSV)). The degree of deoxygenation remained high across the tested hydrotreating conditions, and the products contained < 0.01 wt% oxygen. Increasing hydrotreating pressure from 84 to 125 bar enhanced hydrogenation of aromatic rings and the formation of cycloalkanes and increasing the temperature from 385 to 400 degrees C enhanced cracking and the formation of jet-range molecules. Decreasing the weight hourly space velocity from 0.2 to 0.1 g/(g cat h) further enhanced cracking and led to higher gasoline- and lower jet fuel-range fractions. The highest jet fuel fraction (49 wt%) was obtained at 400 degrees C, 125 bar, 0.2 g/(g cat h) WHSV. CFP oils produced from pine over phosphorous-modified ZSM-5 were hydrotreated at this condition for 588 h to investigate the process durability. The hydrogenation performance of the catalyst gradually stabilized in approximately 300 h after which the product composition remained constant. Of the final hydrotreated CFP oil, 53 wt% fell in the jet fuel range with most of the tested fuel properties meeting ASTM D4054 and/or ASTM D7566 specifications. The freeze points were < -50 degrees C vs. guideline of < -40 degrees C and the viscosities at -20 degrees C were 3.8-4.1 mm 2 /s vs guideline of 8 mm 2 /s. Increasing the fraction of cycloalkanes could increase the cetane number and heating value, which did not meet the guidelines.

09 BIOMASS FUELS↗

Suppressing CO formation in low-temperature methanol steam reforming via Ce-modified CuZnGa layered oxide catalysts

Cu-based layered double hydroxides (LDHs) are widely recognized as effective catalysts for low-temperature methanol steam reforming, yet achieving high hydrogen productivity together with near-complete suppression of CO formation remains challenging. Here, we report the synthesis and evaluation of a series of CuZnGa LDH-derived catalysts and Ce-modified analogues prepared via an aqueous miscible organic method, which enables high metal dispersion and precise structural control. The optimized CuZnGa catalyst exhibits a hydrogen production rate of 16.9 µmol H 2 ·g cat −1 ·s −1 at 180 °C with an H 2 /CO ratio exceeding 3500, outperforming many state-of-the-art low-temperature systems. Importantly, the incorporation of small amounts of Ce further suppresses CO formation while maintaining high hydrogen productivity. Combined spectroscopic characterization and density functional theory calculations reveal that Ce is incorporated into the LDH lattice by substituting Ga 3+ sites up to a critical threshold, beyond which highly dispersed CeO x species are formed. These species provide mobile lattice oxygen that participates in a Mars-van Krevelen-type pathway, selectively oxidizing CO and suppressing the reverse water-gas shift reaction. This study establishes a clear relationship between Ce speciation, oxygen mobility, and catalytic selectivity in LDH-derived systems. The resulting catalysts demonstrate the potential of interface-engineered Cu-based materials for efficient low-temperature hydrogen production with minimal CO contamination.

09 BIOMASS FUELS↗

Graphitization of banana peel – synergistic effect of Ca and other elements of the biomass on carbon structure transformation

Recently, growing interest has been observed in using calcium as an effective catalyst for graphitizing disordered carbon materials derived from biomass and bioprecursors, such as cellulose and lignin, at relatively low tem peratures (<2000 °C). Herein, it is demonstrated that in the presence of elements such as calcium, silicon, sulfur, and potassium, which are abundant in banana peel composed of cellulose and lignin base, graphitization occurs much more effectively. The addition of external calcium source, in the form of calcium carbonate, to the banana peel-derived carbon and heat-treatment of the mixture under protective atmosphere up to 1750 °C results in a significant increase in the degree of the graphitization order and local formation of graphite crystals, whereas the same preparation and heat-treatment procedure applied to carbon material derived from pristine cellulose does not lead to such effective graphitization. It is indicated that the graphitization of banana peel carbon occurs due to the synergistic effect of the external Ca-based catalyst and the internal elements present in the raw biomass, supporting the transformation of the disordered graphene-like layers into graphitic structures. These findings are important for the future production of green graphite from biomass

09 BIOMASS FUELS↗