Search NASA⌕ Search

DOE OSTI · 1898151

Surrogate models for plasma displacement and current in 3D perturbed magnetohydrodynamic equilibria in tokamaks

Abstract

Abstract A numerical database of over one thousand perturbed three-dimensional (3D) equilibria has been generated, constructed based on the MARS-F (Liu et al 2000 Phys. Plasmas 7 3681) computed plasma response to the externally applied 3D field sources in multiple tokamak devices. Perturbed 3D equilibria with the n = 1–4 ( n is the toroidal mode number) toroidal periodicity are computed. Surrogate models are created for the computed perturbed 3D equilibrium utilizing model order reduction (MOR) techniques. In particular, retaining the first few eigenstates from the singular value decomposition (SVD) of the data is found to produce reasonably accurate MOR-representations for the key perturbed quantities, such as the perturbed parallel plasma current density and the plasma radial displacement. SVD also helps to reveal the core versus edge plasma response to the applied 3D field. For the database covering the conventional aspect ratio devices, about 95% of data can be represented by the truncated SVD-series with inclusion of only the first five eigenstates, achieving a relative error (RE) below 20%. The MOR-data is further utilized to train neural networks (NNs) to enable fast reconstruction of perturbed 3D equilibria, based on the two-dimensional equilibrium input and the 3D source field. The best NN-training is achieved for the MOR-data obtained with a global SVD approach, where the full set of samples used for NN training and testing are stretched and form a large matrix which is then subject to SVD. The fully connected multi-layer perceptron, with one or two hidden layers, can be trained to predict the MOR-data with less than 10% RE. As a key insight, a better strategy is to train separate NNs for the plasma response fields with different toroidal mode numbers. It is also better to apply MOR and to subsequently train NNs separately for conventional and low aspect ratio devices, due to enhanced toroidal coupling of Fourier spectra in the plasma response in the latter case.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Liu, Yueqiang (ORCID:0000000281928411), Akcay, Cihan, Lao, Lang L. (ORCID:0000000319372675), Sun, Xuan. 2022-11-15. Surrogate models for plasma displacement and current in 3D perturbed magnetohydrodynamic equilibria in tokamaks. https://doi.org/10.1088/1741-4326%2Fac9d4c

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

On the non-existence of stepped-pressure equilibria far from symmetry

The Stepped Pressure Equilibrium Code (SPEC) (Hudson et al 2012 Phys. Plasmas 19 112502) has been successful in the construction of equilibria in 3D configurations that contain a mixture of flux surfaces, islands and chaotic magnetic field lines. In this model, the plasma is sliced into sub-volumes separated by ideal interfaces, and in each volume the magnetic field is a Beltrami field. In the cases where the system is far from possessing a continuous symmetry, such as in stellarators, the existence of solutions to a stepped-pressure equilibrium with given constraints, such as a multi-region relaxed MHD minimum energy state, is not guaranteed but is often taken for granted. Using SPEC, we have studied two different scenarios in which a solution fails to exist in a slab with analytic boundary perturbations. Here we found that with a large boundary perturbation, a certain interface becomes fractal, corresponding to the break up of a Kolmogorov–Arnold–Moser (KAM) surface. Moreover, an interface can only support a maximum pressure jump while a solution of the magnetic field consistent with the force balance condition can be found. An interface closer to break-up can support a smaller pressure jump. We discovered that the pressure jump can push the interface closer to being non-smooth through force balance, thus significantly decreasing the maximum pressure it can support. Our work shows that a convergence study must be performed on a SPEC equilibrium with interfaces close to break-up. These results may also provide insights into the choice of interfaces and have applications in finding out the maximum pressure a machine can support.

3D equilibrium↗