Search NASA⌕ Search

DOE OSTI · 2000704

Microstructural and phase changes in alpha uranium investigated via in-situ studies and molecular dynamics

Abstract

A deeper knowledge of thermally induced microstructural and phase evolution in nuclear metallic fuel can be obtained using novel in-situ microscopic analyses. Such studies can provide information on the dynamics of phase transitions which is not possible with conventional postmortem characterization (post-irradiation examination). In this work, the behavior of alpha uranium (α-U) was investigated via in-situ heating tests in a transmission electron microscope. Here, the main objective is to understand the microstructural and phase changes, such as defect annihilation and ß phase formation and retention, observed in reactor in-pile transient studies at the Transient Reactor Test facility. Indeed, defect migration and rearrangement were observed within the α phase starting at 673 K; α→ß phase transition was observed between 773 K and 1,073 K during the heating ramp (which is in the temperature window reported for α→ß transition temperatures). Recrystallization and formation of nano grains was observed at high temperatures (over 1,073 K). Such recrystallization was possibly related to the formation of the γ phase. Finally, it was indeed observed that the ß phase (but not γ phase) was retained at room temperature upon rapid cooling. Molecular dynamics studies support these experimental results and shows that the γ phase of pure uranium cannot be retained at room temperature if not stabilized with the addition of an alloying element.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Di Lemma, Fidelma G., Yao, Tiankai, Salvato, Daniele, Capriotti, Luca, Teng, Fei, Jokisaari, Andrea M., Beeler, Benjamin W., Wang, Yuhao, Jensen, Colby J.. 2023-02-15. Microstructural and phase changes in alpha uranium investigated via in-situ studies and molecular dynamics. https://doi.org/10.1016/j.jnucmat.2023.154341

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗