Search NASA⌕ Search

DOE OSTI · 2217002

Enhanced LWR High Burnup Transient Simulation Capabilities to Support AOO Margin Identification

Abstract

As part of ongoing efforts to support the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program’s development of a fuel fragmentation, relocation, and dispersal (FFRD) screening methodology, a number of improvements are required for the NEAMS core simulation capabilities, namely the Virtual Environment for Reactor Applications (VERA). Three areas of improvement were identified in VERA which are important for continued development and application of the FFRD screening methodology. First, the FFRD screening methodology will soon be extended to boiling water reactors (BWRs), requiring development and validation of the VERA BWR capabilities. Second, the screening methodology occasionally requires that VERA be used to simulate a transient in addition to nominal operations. Thus, improvements to both accuracy and performance of the VERA transient capabilities are necessary. Third, the VERAOneWay component of VERA is used to develop BISON fuel performance inputs using the rod-by-rod histories calculated by VERA. Prior use of VERAOneWay exposed significant accuracy, robustness, and performance issues with VERAOneWay; these must be addressed for it to be an effective tool in the NEAMS FFRD methodology. This report documents the efforts in FY23 in each of these three areas to enable successful use of VERA and VERAOneWay for FFRD calculations in FY24 and following years.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Graham, Aaron, Asgari, Mehdi, Henderson, Shane. 2023-09-01. Enhanced LWR High Burnup Transient Simulation Capabilities to Support AOO Margin Identification. https://doi.org/10.2172/2217002

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗