Search NASA⌕ Search

DOE OSTI · 2222978

An attached microalgae platform for recycling phosphorus through biologically mediated fertilizer formation and biomass cultivation

Abstract

Nutrient management is a global challenge for protecting water bodies from eutrophication and for retaining and sustainably recycling phosphorus within the biosphere. This challenge is especially important for water resource recovery facilities (WRRFs) in jurisdictions that limit nutrient loads in plant effluent. A microalgae-based biofilm platform has been designed, constructed, and tested to remove phosphorus and nitrogen from anaerobic digester (AD) effluent filtrate through cultivating biomass and inducing the precipitation of a mineral called struvite (NH₄MgPO₄ · 6H₂O) using a rotating algae biofilm reactor (RABR). RABRs function by rotating a growth substratum through nutrient rich water and then into the atmosphere, immersing microalgae in both sunlight and water. Photosynthesis is utilized in RABR operation to enhance struvite formation by increasing the pH value within the biofilm through the uptake of carbon dioxide from solution. Measurements of pH trended higher with depth through the biofilm when exposed to light confirming the function of photosynthesis in increasing pH and, as a consequence, struvite formation. In addition, reducing RPM allows more time for water to evaporate through exposure of the biofilm to the atmosphere and provides a management option to exceed struvite solubility product. Struvite precipitation was predicted based on chemical analysis and MINTEQ modeling of ADE, was confirmed using Scanning Electron Microscopy and Energy Dispersive X-ray Spectroscopy, and quantified by determining ash content. Increase in pH within the biofilm was confirmed as photosynthetic photon flux density increased. While struvite precipitation and removal from wastewater is conventionally accomplished through physicochemical methods, this research is the first report of struvite enhanced formation through algae biofilm-based photosynthesis processes.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Goldsberry, Parker, Jeppesen, Peter, McLean, Joan, Sims, Ron. 2023-11-30. An attached microalgae platform for recycling phosphorus through biologically mediated fertilizer formation and biomass cultivation. https://doi.org/10.1016/j.clet.2023.100701

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Hydrotreating pine-derived catalytic fast pyrolysis oil to jet fuel: Process durability and impact of operating conditions

Hydrotreating woody biomass-derived catalytic fast pyrolysis (CFP) oil to jet fuel has the potential to enhance energy security due to the large abundance of forest and woody resources. CFP oil produced from pine over ZSM-5 was hydrotreated over sulfided NiMo/Al 2 O 3 for 410 h to study the impact of hydrotreating conditions (pressure, temperature, and weight hourly space velocity (WHSV)). The degree of deoxygenation remained high across the tested hydrotreating conditions, and the products contained < 0.01 wt% oxygen. Increasing hydrotreating pressure from 84 to 125 bar enhanced hydrogenation of aromatic rings and the formation of cycloalkanes and increasing the temperature from 385 to 400 degrees C enhanced cracking and the formation of jet-range molecules. Decreasing the weight hourly space velocity from 0.2 to 0.1 g/(g cat h) further enhanced cracking and led to higher gasoline- and lower jet fuel-range fractions. The highest jet fuel fraction (49 wt%) was obtained at 400 degrees C, 125 bar, 0.2 g/(g cat h) WHSV. CFP oils produced from pine over phosphorous-modified ZSM-5 were hydrotreated at this condition for 588 h to investigate the process durability. The hydrogenation performance of the catalyst gradually stabilized in approximately 300 h after which the product composition remained constant. Of the final hydrotreated CFP oil, 53 wt% fell in the jet fuel range with most of the tested fuel properties meeting ASTM D4054 and/or ASTM D7566 specifications. The freeze points were < -50 degrees C vs. guideline of < -40 degrees C and the viscosities at -20 degrees C were 3.8-4.1 mm 2 /s vs guideline of 8 mm 2 /s. Increasing the fraction of cycloalkanes could increase the cetane number and heating value, which did not meet the guidelines.

09 BIOMASS FUELS↗

Suppressing CO formation in low-temperature methanol steam reforming via Ce-modified CuZnGa layered oxide catalysts

Cu-based layered double hydroxides (LDHs) are widely recognized as effective catalysts for low-temperature methanol steam reforming, yet achieving high hydrogen productivity together with near-complete suppression of CO formation remains challenging. Here, we report the synthesis and evaluation of a series of CuZnGa LDH-derived catalysts and Ce-modified analogues prepared via an aqueous miscible organic method, which enables high metal dispersion and precise structural control. The optimized CuZnGa catalyst exhibits a hydrogen production rate of 16.9 µmol H 2 ·g cat −1 ·s −1 at 180 °C with an H 2 /CO ratio exceeding 3500, outperforming many state-of-the-art low-temperature systems. Importantly, the incorporation of small amounts of Ce further suppresses CO formation while maintaining high hydrogen productivity. Combined spectroscopic characterization and density functional theory calculations reveal that Ce is incorporated into the LDH lattice by substituting Ga 3+ sites up to a critical threshold, beyond which highly dispersed CeO x species are formed. These species provide mobile lattice oxygen that participates in a Mars-van Krevelen-type pathway, selectively oxidizing CO and suppressing the reverse water-gas shift reaction. This study establishes a clear relationship between Ce speciation, oxygen mobility, and catalytic selectivity in LDH-derived systems. The resulting catalysts demonstrate the potential of interface-engineered Cu-based materials for efficient low-temperature hydrogen production with minimal CO contamination.

09 BIOMASS FUELS↗

Graphitization of banana peel – synergistic effect of Ca and other elements of the biomass on carbon structure transformation

Recently, growing interest has been observed in using calcium as an effective catalyst for graphitizing disordered carbon materials derived from biomass and bioprecursors, such as cellulose and lignin, at relatively low tem peratures (<2000 °C). Herein, it is demonstrated that in the presence of elements such as calcium, silicon, sulfur, and potassium, which are abundant in banana peel composed of cellulose and lignin base, graphitization occurs much more effectively. The addition of external calcium source, in the form of calcium carbonate, to the banana peel-derived carbon and heat-treatment of the mixture under protective atmosphere up to 1750 °C results in a significant increase in the degree of the graphitization order and local formation of graphite crystals, whereas the same preparation and heat-treatment procedure applied to carbon material derived from pristine cellulose does not lead to such effective graphitization. It is indicated that the graphitization of banana peel carbon occurs due to the synergistic effect of the external Ca-based catalyst and the internal elements present in the raw biomass, supporting the transformation of the disordered graphene-like layers into graphitic structures. These findings are important for the future production of green graphite from biomass

09 BIOMASS FUELS↗