Search NASA⌕ Search

DOE OSTI · 22493778

Simulating plasma production from hypervelocity impacts

Abstract

Hypervelocity particles, such as meteoroids and space debris, routinely impact spacecraft and are energetic enough to vaporize and ionize themselves and as well as a portion of the target material. The resulting plasma rapidly expands into the surrounding vacuum. While plasma measurements from hypervelocity impacts have been made using ground-based technologies such as light gas guns and Van de Graaff dust accelerators, some of the basic plasma properties vary significantly between experiments. There have been both ground-based and in-situ measurements of radio frequency (RF) emission from hypervelocity impacts, but the physical mechanism responsible and the possible connection to the impact-produced plasma are not well understood. Under certain conditions, the impact-produced plasma can have deleterious effects on spacecraft electronics by providing a new current path, triggering an electrostatic discharge, causing electromagnetic interference, or generating an electromagnetic pulse. Multi-physics simulations of plasma production from hypervelocity impacts are presented. These simulations incorporate elasticity and plasticity of the solid target, phase change and plasma formation, and non-ideal plasma physics due to the high density and low temperature of the plasma. A smoothed particle hydrodynamics method is used to perform a continuum dynamics simulation with these additional physics. By examining a series of hypervelocity impacts, basic properties of the impact produced plasma plume (density, temperature, expansion speed, charge state) are determined for impactor speeds between 10 and 72 km/s. For a large range of higher impact speeds (30–72 km/s), we find the temperature is unvarying at 2.5 eV. We also find that the plasma plume is weakly ionized for impact speeds less than 14 km/s and fully ionized for impact speeds greater than 20 km/s, independent of impactor mass. This is the same velocity threshold for the detection of RF emission in recent Van de Graaff experiments, suggesting that the RF is correlated to the formation of fully ionized plasma.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Fletcher, Alex, Close, Sigrid, Mathias, Donovan. 2015-09-15. Simulating plasma production from hypervelocity impacts. https://doi.org/10.1063/1.4930281

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Fast solvers for tokamak fluid models with PETSc

Multigrid (MG) is widely recognized as a highly effective solver for the model problem, the Laplacian, but textbook MG fails on most problems of interest. MG methods have been applied to complex, real-world applications with careful consideration of the physical model and discretization. In this work we develop the first step in applying MG methods to science and engineering relevant magnetohydrodynamics (MHD) tokamak models in the M3D-C1 (https://m3dc1.pppl.gov) fusion energy science code. The semi-implicit time integrator in M3D-C1 is composed of many linear solves. The implicit advance of the momentum equation is the most challenging and is the focus of this work. The current production solver in M3D-C1 is a block Jacobi (BJ) preconditioner within a Krylov solver, where blocks group degrees of freedom on planes of constant toroidal coordinate. BJ convergence degrades as the number of planes increases due to the spectral properties of the matrix preconditioned with BJ. The partially magnetic field-aligned, regular toroidal grid structure in M3D-C1 is amenable to semi-coarsening geometric MG in the toroidal direction. This paper develops such a solver and demonstrates competitive performance on a runaway electron model of a SPARC (https://cfs.energy/technology/sparc) disruption, and superior robustness on a stellarator model on which the BJ solver fails to converge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Final Report: A Multi-Channel Fusion Product

The goal of this project was to measure charged fusion products from the d(d,p)t reaction in MAST-U plasmas as a function of time and position with good energy resolution using a system of up to six charged particle detectors. The data from this new diagnostic will make it possible to determine the neutral beam ion density profile as a function of R, z, and t with reduced model dependency and contribute new information to a global analysis of fast ion diagnostic data needed for the determination of the fast ion distribution function (velocity space tomography).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Unitary Qubit Lattice Algorithms for Plasma Physics

This final technical report summarizes research conducted under DOE Award DE-SC0021653 to develop unitary Quantum Lattice Algorithms for modeling electromagnetic wave propagation and scattering in complex media, including plasmas. The project developed and validated quantum-inspired formulations of Maxwell's equations that preserve unitary evolution and can be evaluated on classical high-performance computing systems while providing a foundation for future quantum-computing implementations. Major accomplishments include the development of two- and three-dimensional algorithms for electromagnetic scattering; scalable, distributed-memory implementations demonstrated on the Perlmutter supercomputer; formulations for nonlinear lossless fluid dynamics and cold, lossless, inhomogeneous magnetized plasmas; and an explicit quantum algorithm for a time-discretized Lorenz model. Simulations reproduced a range of characteristic wave phenomena, including transient effects that are not readily apparent in conventional frequency-domain studies, demonstrating the effectiveness of the proposed approach for modeling complex electromagnetic and plasma systems. The work establishes a unified theoretical and computational framework for quantum and quantum-inspired simulation and provides a foundation for future implementation on fault-tolerant quantum systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗