Search NASA⌕ Search

DOE OSTI · 23042918

CFD-Informed Spacer Grid Models in the Subchannel Code CTF

Abstract

Data from computational fluid dynamics (CFD) simulations can be utilized to improve the predictive capabilities of the subchannel code CTF. Past work incorporating CFD results into CTF has included accounting for directed crossflow and turbulent mixing between adjacent subchannels. Spacer grids impact fluid flow in various ways, and this work focuses on four spacer grid effects, namely: 1. Directed crossflow; 2. Turbulent mixing; 3. Enhanced downstream heat transfer; 4. Pressure drop correlation. Heat transfer augmentation occurs partially due to the disturbances in the developed flow and from the additional turbulence generated by the presence of obstructions in the fluid flow's path. The boundary layer disruption is caused in part by the newly-directed flow just downstream of the spacer grid vanes. This effect lessens as the distance from the grid increases and the flow returns to its developed state, closer to what would be expected in a bare subchannel. Current plans of this work are to develop a method for incorporating the effects of spacer grids on the heat transfer calculation within CTF. Proposed techniques include the addition of an enhancement factor to the local heat transfer coefficient. The inclusion of CFD data from properly-designed simulations will allow CTF to better predict parameters such as fluid temperatures near spacer grids. Improved pressure loss coefficients for each grid can also be generated using CFD simulations. The heat transfer modification has been studied, with other authors noting correlations which are dependent on grid properties such as the blockage ratio. Parameters considered in this study are the turbulent kinetic energy (TKE) and vorticity. There are currently no models to calculate or store either of these parameters within CTF. When accounting for spacer grid effects in CTF, it is important to not double-count the effects towards two different CTF models. This requires carefully designing CFD simulations around capturing specific phenomena from the grids and being able to apply these CFD results to all appropriate flow conditions. (authors)

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Blyth, Taylor, Salko, Robert, Avramova, Maria. 2016-07-01. CFD-Informed Spacer Grid Models in the Subchannel Code CTF. https://searchnasa.com/record/osti%3A23042918/cfd-informed-spacer-grid-models-in-the-subchannel-code-ctf

Citations retain the original authors and DOI and include this site’s record URL. If this discovery service contributed to your research, you can also cite Search NASA by Indiciae: BibTeX · RIS.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗