Search NASA⌕ Search

DOE OSTI · 2481567

A model for trapping and re-solution regarding intra-granular bubbles in UO 2 , linked to atomic-scale simulations

Abstract

In the literature, a clear definition of the irradiation re-solution frequency of gas from bubbles in the UO 2 fuel is absent. Moreover, for intra-granular bubbles, a detailed calculation of the cumulated displaced gas quantities in function of the distance from the radius of the bubble after a re-solution event has never been published. The assessment of these two elements is very useful if we want to increase the adherence of fission gas release codes to our present knowledge of the behavior of fission gases. Hence, we suggest to link the definition of the re-solution frequency to atomic-scale simulations. Furthermore, we present the cumulated displaced gas quantities obtained from Molecular Dynamics calculations, from which we have derived a re-solution profile that can be exploited to better consider the irradiation re-solution phenomenon inside Fission Gas Release codes. On top of that, we have built a new trapping/re-solution model for intra-granular bubbles linked to Molecular Dynamics simulations that can be easily incorporated into Fission Gas Release codes. In conclusion, we also check that the model is properly built through the comparison of the new model against a reference.

Explore related subjects

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Vergani, M. [CEA, DES, IRESNE, DEC, Saint Paul Lez Durance (France)] (ORCID:0009000818891661), Cooper, M. W. D. [Los Alamos National Laboratory (LANL), Los Alamos, NM (United States)] (ORCID:0000000182707947), Noirot, Laurence [CEA, DES, IRESNE, DEC, Saint Paul Lez Durance (France)] (ORCID:0000000347689899). 2024-12-10. A model for trapping and re-solution regarding intra-granular bubbles in UO 2 , linked to atomic-scale simulations. https://doi.org/10.1016/j.jnucmat.2024.155562

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗