Search NASA⌕ Search
Home/Archive/DOE OSTI

DOE OSTI · 3001366

Device for steam cladding oxidation testing at TREAT

Moussaoui, Musa A. [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000164016712)·Anderson, Klint Stephens [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000259773759)·Yoo, JunSoo [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000339233701)·Woolstenhulme, Nicolas E. [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000278813314)
View original source ↗Read source document ↗Export metadata ↓

Abstract

To compare the chemical degradation of conventional zirconium alloy (Zry) cladding to advance silicon carbide (SiC) cladding in a post loss of coolant accident (LOCA) environment, new nuclear testing capabilities are necessary. The Transient Reactor Test (TREAT) Facility at Idaho National Laboratory (INL) has matured its transient fuel testing capabilities since its 2017 restart. The most recent experiment architecture is the Transient Water Irradiation System in TREAT (TWIST), which is designed to support qualification of accident tolerant fuels in light water reactors. INL has designed and analyzed a natural circulation steam flow modification for TWIST to produce prototypic conditions of cladding oxidation. The in-situ device will be electrically heated to drive natural circulation. Moreover, the SiC cladding requires heating above 1700 °C to observe failure, thus internal prototypic nuclear heating with radiation effects will be used. Thermal hydraulic analysis with RELAP5-3D (Reactor Excursion and Leak Analysis Program) estimated steam fluxes greater than 50 mg cm −2 s −1 can be achieved. These fluxes are adequate to test Zry cladding according to draft regulatory guides and to test SiC cladding according to past experiments.

Explore related subjects

OxidationSilicon CarbideTransient Testing

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Moussaoui, Musa A. [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000164016712), Anderson, Klint Stephens [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000259773759), Yoo, JunSoo [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000339233701), Woolstenhulme, Nicolas E. [Idaho National Laboratory (INL), Idaho Falls, ID (United States)] (ORCID:0000000278813314). 2025-09-10. Device for steam cladding oxidation testing at TREAT. https://doi.org/10.1016/j.nucengdes.2025.114441

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related reports

NASA NTRS2017

Investigation of the High-Energy Oxidation of FiberForm from DSMC Analysis of Molecular Beam Experiments

A collaborative effort between the University of Illinois at Urbana-Champaign (UIUC), NASA Ames Research Center (ARC) and Montana State University (MSU) succeeded at developing a new finite-rate carbon oxidation model from molecular beam scattering experiments on vitreous carbon (VC). We now aim to use the direct simulation Monte Carlo (DSMC) code SPARTA to apply the model to each fiber of the porous fibrous Thermal Protection Systems (TPS) material FiberForm (FF). The detailed micro-structure of FF was obtained from X-ray micro-tomography and then used in DSMC. Both experiments and simulations show that the CO/O products ratio increased at all temperatures from VC to FF. We postulate this is due to the larger number of collisions an O atom encounters inside the porous FF material compared to the flat surface of VC. For the simulations, we particularly focused on the lowest and highest temperatures studied experimentally, 1023 K and 1823 K, and found good agreement between the finite-rate DSMC simulations and experiments.

Oxidation↗
NASA NTRS2016

Why Do Models Overestimate Surface Ozone in the Southeast United States?

Ozone pollution in the Southeast US involves complex chemistry driven by emissions of anthropogenic nitrogen oxide radicals (NO(x) triple bond NO + NO2) and biogenic isoprene. Model estimates of surface ozone concentrations tend to be biased high in the region and this is of concern for designing effective emission control strategies to meet air quality standards. We use detailed chemical observations from the SEAC(exp 4)RS aircraft campaign in August and September 2013, interpreted with the GEOS-Chem chemical transport model at 0.25 deg x 0.3125 deg horizontal resolution, to better understand the factors controlling surface ozone in the Southeast US. We find that the National Emission Inventory (NEI) for NO(x) from the US Environmental Protection Agency (EPA) is too high. This finding is based on SEAC(exp 4)RS observations of NO(x) and its oxidation products, surface network observations of nitrate wet deposition fluxes, and OMI satellite observations of tropospheric NO2 columns. Our results indicate that NEI NO(x) emissions from mobile and industrial sources must be reduced by 30-60%, dependent on the assumption of the contribution by soil NO(x) emissions. Upper-tropospheric NO2 from lightning makes a large contribution to satellite observations of tropospheric NO2 that must be accounted for when using these data to estimate surface NO(x) emissions. We find that only half of isoprene oxidation proceeds by the high-NO(x) pathway to produce ozone; this fraction is only moderately sensitive to changes in NO(x) emissions because isoprene and NO(x) emissions are spatially segregated. GEOS-Chem with reduced NO(x) emissions provides an unbiased simulation of ozone observations from the aircraft and reproduces the observed ozone production efficiency in the boundary layer as derived from a regression of ozone and NO(x) oxidation products. However, the model is still biased high by 6 plus or minus 14 ppb relative to observed surface ozone in the Southeast US. Ozonesondes launched during midday hours show a 7 ppb ozone decrease from 1.5 km to the surface that GEOS-Chem does not capture. This bias may reflect a combination of excessive vertical mixing and net ozone production in the model boundary layer.

Oxidation↗