Search NASA⌕ Search
Home/Archive/DOE OSTI

DOE OSTI · 3377423

Characterization of NBCMA—A DAPO Precursor

Gwyn, Angela Christine (Christi) [Pantex Plant (PTX), Amarillo, TX (United States)]
View original source ↗Read source document ↗Export metadata ↓

Abstract

As part of our investigation into the process optimization of 2,6-diaminopyrazine-1-oxide (DAPO), small-scale sensitivity testing (impact, friction, and ESD) was conducted on the precursor, N-nitroso-bis(cyanomethyl)amine (NBCMA). NBCMA exhibited moderate sensitivity to friction, whereas no sensitivity to impact or spark was observed.

Explore related subjects

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CHEMISTRY42 ENGINEERING

Keep this discovery

BibTeXRIS

Gwyn, Angela Christine (Christi) [Pantex Plant (PTX), Amarillo, TX (United States)]. 2026-06-03. Characterization of NBCMA—A DAPO Precursor. https://doi.org/10.1002/prep.70195

Cite the original work for its findings. Save a collection to share your selection of sources.

Discover connections

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CHEMISTRY subject42 ENGINEERING subject

Connections use source metadata and explicit phrase matches, not verified experimental comparisons.

KEEP EXPLORING

Related discoveries

DOE OSTI2026

The effect of dogbone sample size in the tensile testing of TATB-based plastic‑bonded explosive materials

Mechanical properties are of interest for many plastic‑bonded explosive (PBX) materials with tensile properties being of particular interest. Direct tensile measurements using dogbone-shaped samples are considered the gold standard, but they are fairly large, making testing more costly and less desirable from a safety perspective. We investigated whether the measured tensile strength depends on the dogbone specimen size, which to our knowledge, has not been reported in the literature for PBX materials. Understanding this should inform the feasibility of employing smaller samples and how sample size should be considered when comparing PBX dogbone values in the literature. The TATB-based PBX dogbone sample size was varied by (a) scaling all dimensions proportionally and (b) varying only the length of the samples. It was observed that the measured tensile peak stress (strength) was a function of the sample size, and was more dependent on the diameter (cross-sectional area) than the length of the samples. Since peak stress is calculated as peak force normalized to the diameter of the sample, one might not expect an explicit diameter dependence for the peak stress. Therefore, these results suggest there may be an additional strengthening effect as the sample diameter is increased.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Shear and combustion characterization of printable ammonium perchlorate composite propellant formulations

Seven formulations of ammonium perchlorate composite propellant (APCP) are developed and their properties relevant for successful additive manufacture are characterized. Extrusion in a custom-built 3D printing system and spindle viscometry are used to collect viscosity measurements of curing primary and non-curing secondary versions of the formulations. The formulations that behave similarly to a Bingham plastic, with apparent viscosities between 4 and 8 thousand Pa*s at 30 minutes post-mix, are determined to be most suitable for printing applications. Measurements of one material show a yield stress of 1 kPa. Ambient pressure burn rates of 2.0–2.9 mm/s were measured for the compositions tested. All measured burn rates were comparable to the lower end of typical burn rates for APCP. In conclusion, the results of the characterization demonstrate a propellant suitable for use in a 3D printing system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Biocatalyst discovery and design for plastics deconstruction: A multi‐scale perspective

Plastic waste accumulation poses significant environmental challenges due to a lack of economical solutions for the molecular deconstruction of diverse synthetic polymers. Biological‐based degradation offers promise but is hindered by the crystallinity, hydrophobicity, and additive complexity of plastics, which restrict biocatalyst access and activity. To address these problems, we propose a multi‐scale framework that combines detailed materials characterization, optimization of plastic‐biomolecular interfacial interactions, and enhancement of biocatalytic kinetics to develop effective plastic‐deconstructing enzymes. This approach leverages principles from reaction kinetics, transport and interfacial phenomena, and enzyme engineering to systematically address barriers across diverse plastic types. Our framework aims to accelerate the discovery and optimization of biocatalysts capable of scalable, selective, and efficient deconstruction of plastic waste. These advances hold potential to enable sustainable biological recycling and upcycling pathways, contributing to global efforts in mitigating plastic pollution and promoting circular material economies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗